How to Stlink 3 capacitor controller for G30 **NEW METHOD IN DESCRIPTION**
Vložit
- čas přidán 12. 11. 2022
- New method :
• Speedhack Ninebot G30 ...
Here is a video how I do it the long way and also you have info on how the stink program is working. In this video I only show the front connectors for st link.
• Ninebot Max G30D and G... - Hry
Man great video, love your work!!! and Happy 2023!!! I am glad you put this out for the Ninebot Max users!!! Is gonna be big help for many!!! If ok with you I will like to post your work in my Esnkaz Group? I am sure you know who I am as well jejeje. I was going to upload my way of ST-link back in October 2022 but I got a bunch of haters whom didnt agree with the idea... So I end up not posting it. I was thinking in doing it again, so I decided to see if anyone else had done it, and I am super happy man you did it!!! Esnkaz thank you!!!! 🙏 I just subscribed to your channel as well! Blessings my friend! is great work!
Thanks man! Great to here you like it. Not my best solder job but still it works. You can also press nails on there to skip tiny solder job :)
I have order smaller solder tips so maybe to a cleaner job later :)
Don't mind people be negative becuse its always the beat way for you that counts. Not always optimal for others :)
Thanks for sending me a positive message and happy 2023 :)
@@WattsnabbAB Jejeje I dont solder I have tools for it and even like that sometimes is hard to make it work. Specially with coffee in lol. In any case is great work! Ok to post in my group?
@@esnkaz yes of course:)
Best STLINK videos in the world, you are great! Thanks for replying, I have another question: I bought the soldering iron, at what temperature should I set it to make a correct weld? For the first time, is it easier in the back or front of the controller? I don't have the grinding pen.
I have the exact same controller in this video, in other online guides the front connectors are in another place and no grinding pen is needed.
Are you sure those are the only front connectors? In the forum rollerplausch scheme indicates without grinding pen in another front point.
Hi
Its all depends on what soldering iron you have. You have to practice on other board just to learn first. Then you will notice what temperature is the best. Between 330-370c try in that range. Becuse its also depends on what solder you have and what tip. So solder in the front pin you need to have a microscope and skill with the solering pen. The back connect I have a video on also. just mesure this pins and know they are working, maybe there are more pins but don't know actually. So the pins on the back is easier but it's harder to get the controller of. But like I sayed I have a video on that to. :)
I actually use a piece of wood that I sharpen an edge on and push it down into the silicone. Less chance of cutting components with wood.
Yeah maybe. They are so tiny so just by looking at them they can get damage :)
Same method here.
Do you know how to flash the new SNSC controllers with AT32F chip
It depends on controller but same process but the connectors may be on other place.
Can you please help I try flashing a custom firmware and now I'm stuck on 12 mph I tried flashing other custom firmware but I have no luck I wanted to know if I replace the whole controller to a brand new one will it take it back to 18 mph
Hi. If you buy our costumfirmware controller
www.wattsnabb.se/products/ninebot-g30-max-modellerna/reservdelar-till-ninebot-g30-max-modellerna/original-ninebot-g30-g30d-max-moderkort-kontrollkort
Then it will work. I cant speak for other vendors.
Varför göra det så omständigt? Du har ju St-link paddar precis nedanför mitten kondingen. SWDIO till vänster, SWCLK mitten. GND och 5V kan matas genom någon kontakt.. Jag gjorde en jigg och 2st synålar så slipper man ta bort silikonet.
Tror du har missat senare videos :)
can we flash any controller ? cause all of bldc controllers got on port
Yes if you reverse engineer the program all controllers can be hacked.
Am I wrong but can’t you just buy a new controller and program it ? I see them even on Amazon.
Have you tryed buying them to confirm they are original? Its cheeper to st link them due to many have limited economic =)
Vart hittar man din verkstad?
www.wattsnabb.se
Vikstensvägen 63
We use only needle and work very good without removing silicon 😂😂😂
Yeah already done a video with it. Check newer video on my channel :)
You know there are Pins, U dont have to Connect directly to stm32F lol
Yes I have a video about that. But the pins are on the back of the controller.
@@WattsnabbAB ahhh OK✌🏻
@@WattsnabbAB i search a video about Ninebot e22d, but i would take 5v and ground from the dashboard + and - connection.
Can i go like this?
@@mr.taddel4282 havent tryed it on them but I think it also work.
@@WattsnabbAB yees, IT worked