Keep the awesome content coming Boston, your work and videos are GREAT. Screw all these lame ass losers who love to hate and make comments when there own shit probably looks like trash. To each his own and it’s all about loving what you do and making it fun. I’m a plumber in CA and I love all your videos and content. I appreciate all the time you take to entertain us ungrateful assholes. Keep it Brotha! Much love and respect!!!
Those are nice looking manifolds... might be a bit close for insulation too but it looks great. Once wrapped the insulation might be close but probably won't be touching side to side... im guessing there'd be about a ½" gap if 1" thick insulation is used...
This shows what you know about plumbing. A professional would have used the snoakford technique on those cuts , a Wilson clamp and dab of cosunatre before you fired up them pipes.
Dude... I don't use em but it took a half a second to check that. Sioux Chief has 12 port 2" × ¾" open end copper manifolds... and they're not alone...
It makes both servicing a section easy as well as facilitating the purging of air out of each zone.. if there's air in a line the pump sometimes will push everywhere else instead, leaving that section air locked and without flow... Those boiler drains are great for hooking a hose up to and blowing out all the bubbles 🫧
No not pumping, this is municipal water thats where the pressure is coming from you can see the meter in the video. No, at 3:39 he makes a comment about pulling the tees in regards to some tools or a specific tool idk
@@jakeb.4225 I'll be honest with ya' ... I only half watched the video . . 😆 other stuff was playing on a different screen... Sure looked like hydronics... especially with boiler drains on each of those lines on one side... I use a boiler drain on each return and valve both ends... and that's if there isn't already flowsets to put on the supplies and returns.
@@jakeb.4225 there's a big tool for pulling a short nipple out of copper pipe where you can then braze a pipe into that socket... when we say PULLING TEES that's usually what we mean... maybe that was what you were asking about... 😏
First time watching this guy/kid and he’s actually sitting there talking shit about his viewers that I’m sure keeps him paid on the side but yall keep watching his vids 🤔 i get why homeboy didn’t want it to look like shit reducing the t’s but since ya not minding spending a few extra bucks for looks why not spend a cpl more on top and make it all press save some time and you could of went and replaced your sister’s faucet at the end of the day instead of postponing 😂😂😂😂😂😂👍
Cost... press fittings are stupid expensive - I hate pressed fittings. Somewhere someday a class action lawsuit will happen when the wrong big building has the seals inside the fittings rot out from some small change in the water supply... 😂 let's see if it outlives pex. That's another future problem waiting to happen... remember quest fittings?
@@JoeA1974 tbh I agree with you 💯 on the class action until then it’s $650 not $325 for me and you can not tell me you haven’t opened up a wall and a brass pex 90 or coupling is leaking and had to c/r
@someguy5438 they're heavy and don't travel as easy.. I have a whole solder kit with cutters, file, sandcloth, brushes, flux, solder & Mapp gas bottle in one of the half size Milwaukee packout boxes.. I can't stick my B bottle in anywhere like that tight or as lightweight.
@@someguy5438 the jobs I'm working are 1 to 2 year projects or more... I just got tired of dragging a big bottle around so often. Especially on multi-story, multi-family... and double, especially when there's no lift
I did a 4 jug whole house water filtering system yesterday and I think I got high on solder, flux and copper fumes 🫠, btw a roll of solder is $58 at HD.
holy shit you hit 100k! Holy shit x2 this one was super awesome with the editorial!! hell yea me and my wife are laughing our asses off! "Let'er rip"!
👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻… the monstah strikes again. Cleannnnn
The header looks awesome!!
Nice looking work! Thanks for sharing!
Now heres the man!
Incredible soldering job!
Hey man! Thanks for adding a zip up hoodie can't wait!
That looks great - well done
Ya sistah loves my two inch header kid 😂😂🎉
Great job bro..real plumbers soilder
Is it true Mapp gas was banned in 08 and now same as propane?
Love your videos
Do you leave a hot and cold shut off at each level and/or dwelling?
Great work man
LMFAOING , SUBSCRIBED AND BUYING ONE OF THOSE THONGS LOL. Keep it UP LMAO FUNNY STUFF
Keep the awesome content coming Boston, your work and videos are GREAT. Screw all these lame ass losers who love to hate and make comments when there own shit probably looks like trash. To each his own and it’s all about loving what you do and making it fun. I’m a plumber in CA and I love all your videos and content. I appreciate all the time you take to entertain us ungrateful assholes. Keep it Brotha! Much love and respect!!!
Great work you are the best!!!!!!!!)
THXS FOR SHARING...
Looks beautiful
Nice dude!
Bam!! Thats how u do it!!! My man
Great looking job. Enjoy your videos. No leaks either
Great job
That's a great idea using two torches at once to heat that 2 inch it needs the extra BTUs
Those are nice looking manifolds... might be a bit close for insulation too but it looks great. Once wrapped the insulation might be close but probably won't be touching side to side... im guessing there'd be about a ½" gap if 1" thick insulation is used...
For the money in those tee's I would have just invested in a header making tool. It allows for far more customization.
Awesome
Nice to see plumbers solder, Pro
Nice manifold. Clean sweating. 👍
Where is the flooded basement? Maybe its just me but I'm never dry when i do this kinda stuff
True test, let it heat up. Thats where the dreaded drip will be once your tools are out of the house 😂
Will be leaking first pressure test😂😂😂😂
This shows what you know about plumbing. A professional would have used the snoakford technique on those cuts , a Wilson clamp and dab of cosunatre before you fired up them pipes.
Bill burr is a plumah ?
👍👍
Wait why not ball valves?!
Was wondering if they make 2 x 3/4 headers? I use 11/4 by 3/4 headers all the time. They save a ton of time.
Dude... I don't use em but it took a half a second to check that.
Sioux Chief has 12 port 2" × ¾" open end copper manifolds... and they're not alone...
Webstone is built in Worcesta
😂❤
What was all the valves for?
my guess would be for the ability to drain down the individual apartment / unit in case of maintenance.
It makes both servicing a section easy as well as facilitating the purging of air out of each zone.. if there's air in a line the pump sometimes will push everywhere else instead, leaving that section air locked and without flow...
Those boiler drains are great for hooking a hose up to and blowing out all the bubbles 🫧
That's really nice work.
The only thing I'm not impressed with is that Baaaston aaccent!
Whats "pulling the tees"?
You mean pumping? What is making it flow?
There is a pump upstream from one of those manifolds...
No not pumping, this is municipal water thats where the pressure is coming from you can see the meter in the video. No, at 3:39 he makes a comment about pulling the tees in regards to some tools or a specific tool idk
@@jakeb.4225 I'll be honest with ya' ... I only half watched the video . . 😆 other stuff was playing on a different screen...
Sure looked like hydronics... especially with boiler drains on each of those lines on one side... I use a boiler drain on each return and valve both ends... and that's if there isn't already flowsets to put on the supplies and returns.
@@jakeb.4225 there's a big tool for pulling a short nipple out of copper pipe where you can then braze a pipe into that socket... when we say PULLING TEES that's usually what we mean... maybe that was what you were asking about... 😏
@JoeA1974 yes I've seen that I know what was meant in the vid, basically turning a piece of pipe into a tee fitting, thanks
First time watching this guy/kid and he’s actually sitting there talking shit about his viewers that I’m sure keeps him paid on the side but yall keep watching his vids 🤔 i get why homeboy didn’t want it to look like shit reducing the t’s but since ya not minding spending a few extra bucks for looks why not spend a cpl more on top and make it all press save some time and you could of went and replaced your sister’s faucet at the end of the day instead of postponing 😂😂😂😂😂😂👍
Cost... press fittings are stupid expensive - I hate pressed fittings. Somewhere someday a class action lawsuit will happen when the wrong big building has the seals inside the fittings rot out from some small change in the water supply... 😂 let's see if it outlives pex. That's another future problem waiting to happen... remember quest fittings?
@@JoeA1974 tbh I agree with you 💯 on the class action until then it’s $650 not $325 for me and you can not tell me you haven’t opened up a wall and a brass pex 90 or coupling is leaking and had to c/r
And here's me... cleaning each nipple after I cut them...😂😂
Get a b-tank bro.
For big stuff... us OG's like the lighter bottle for small pipes.
@JoeA1974 a b tank is superior in almost any circumstances. Pat an a 2 tip and a long hose, you can get anywhere.
@someguy5438 they're heavy and don't travel as easy.. I have a whole solder kit with cutters, file, sandcloth, brushes, flux, solder & Mapp gas bottle in one of the half size Milwaukee packout boxes.. I can't stick my B bottle in anywhere like that tight or as lightweight.
@JoeA1974 True that. I'm used to jobs that are several weeks or months long and find a b tank on a little dolly very useful.
@@someguy5438 the jobs I'm working are 1 to 2 year projects or more... I just got tired of dragging a big bottle around so often. Especially on multi-story, multi-family... and double, especially when there's no lift
Wasted so much time...
I did a 4 jug whole house water filtering system yesterday and I think I got high on solder, flux and copper fumes 🫠, btw a roll of solder is $58 at HD.
Imagine having the time to tape and edit videos of doing a job that thousands of plumbers do everyday, believing the way you do it is special. 😄
I’d take the time to do it too if I was making money off videos like he is 👍
You watched it didn't you? 😂
@@Flakester Some of it. Dime a dozen.
Don’t be jelly (:
@@mycaddigo Don't be a hick.