Creality Halot One - Resin 3D Printer: Setup, Test and Review
Vložit
- čas přidán 5. 08. 2021
- Buy a Halot One: www.creality3dofficial.com/co...
Support TOC on Patreon: / theoutercircle
Our bling shop - shop.spreadshirt.com.au/TheOu...
TOC Instagram - / theoutercircle
TOC Facebook page - / theoutercircle
Heads up, vinyl gloves dissolve in the resin. You need proper latex or nitrile
Latex gloves are needed? Thank you for this very important heads-up
@@joshwarrey3728 many latex gloves are actually vinyl. buy nitrile
@@ravener96 Good to know.
Holy sh.. Thanks for the headsup
This stream was a surprise to be sure, but welcome one
New to printing, this review gave me a better and concise tutorial than some of the stuff i have seen
The way it cleans itself at the end is rather satisfying to watch, peeling that entire resin sheet out 🤤
14:06 That evil piece of support (especially with a foot) can become your friend. Place it in the corner of the vat foot down, just on the corner of the cleaning exposure. Then use the support to lift the whole exposed clean sheet in one go. ;-)
That's a good machine. Just never spill the resin. Also wear goggles when you snap off supports as tiny bit of liquid and solid resin fly everywhere. The liquid resin also adheres to your glasses if you wear them so goggles help a lot.
Thanks for this heads-up as I plan to acquire this printer.
Hey TOC, Pascal here from EdgeMiniatures, so cool to see you using one of my minis for the test print! Great introductury video too, keep it up! :D
It’s honestly astonishing what a couple hundred bucks can get you straight out of the box, I did not know this until I bought my anycubic photon mono, and I kind of feel like people have the same opinions on 3d printing I used to. I used to think it was hard and time consuming and expensive, but things are definitely changing, it’s a lot easier and cheaper than it used to be and for an arguably equivalent product. Every time I pop something off the build plate it makes me curious what some miniature companies plan to do about it.
I think alot of people think fdm printers when you talking about 3d printing
We still rely on miniatures companies because we don't know how to design our own miniatures and convert to printable files
@@rking1106 there are actually videos explaining how to make trhem in blkender and print them, trhe revolution is soon.
its on sale right now at my local microcenter for only 99$ im thinking of picking it up now
I've just bought this printer for 120 bucks as it was 50% off! thats incredible. I used to pay almost that amount to print my prototypes at a 3d printing service.
Thank you for this video. Answered all the questions I wanted to know. I've subbed
The cleaning feature is mind blowing that no one else thought off , this might be perfect entry to get me started until I "need" to go bigger 😅
Got mine yesterday and it’s great! Had the first print fail because of the settings but the second went perfectly and it looks like the pause feature has been updated.
80% done printing a Thunderhawk!
That's free real estate ;D
They realy repaired the pause feature ?
That is the only thing i was afraid of
I’m thinking about getting one for 40k models. Do you think it would work for that?
@@oneshotgaming3961 It'll do infantry, tanks, titans, pretty much anything the build plate will allow. Though I'd recommend getting the Halot one pro if it's still on sale, bigger built plate and better resolution.
Drinking Game: Shotgun a tinny every time Macca says, "Rather nasty stuff".
Very informative, great clip thank you!
Got mine today! Thanks for the video!
How is it
Thank you for this, me and the boys thinking about getting this modell to :)
Glad I could help! As I said, buy what you need not what suits me best.
@@TheOuterCircle yeah we looked up some printers, and this one is one we think about. Your video was really really helpful :)
Thinking on getting one for making some d&d stuff it will be my very first printer
QUESTION: Instead of using paper during the calibration of the Plate, Would leaving the plastic on function the same? Please advise.
Great vid, thanks.
Thanks for the video
Is it accurate enough to print 1/28 scale car logo and badges? Thinking of getting one of these printers to print the car logos for 1/28 Kyosho Mini Z white bodies
Very helpful thank you! Perhaps a video on the 'washing & curing' you did?
Does it matter what type of resin you should use if so what type should i get for the halot?
Very informative
I would like to add that with the resin, if you leave the resin in the printer for a while, you may have to stir it around due to separation.
That’s good advice.
Enjoyed the review mate! How is it holding up? I'm about to make the purchase on this but still torn between the halot one and photon mono. Do you have any insights?
Got a couple of questions (I just got mine...)...#1. Do you need to adjust any printing settings in the machine itself? #2. What printing SW do you use? Any recommended/free by the manufacturer? #3 do you keep the resing in the VAT for the next print or is it better to filter and store it back in the bottle? #4. did you do NO curing on the piece? nor alcohol nor UV? if so, is it because of the type of resin you used?...
After more than 10 attempts, and every time the platform is empty of any printed form, please, is there any help!?
Can you please do a video on how to find a good site to order 3D printing from? Maybe some indication on what type of printers to look out for when I ask them what they use in their studios? For things like very crisp fine detailing. (I am not sure if I will be able to accommodate my own 3D printer at home for a very long time at very least, so this kinda info can be helpful for myself and many others in similar situation). Thanks so much :)
It's not about the printer, it's about how you set it up. If they run a pretty expensive model, you can generally assume they give a damn about the quality. If it's a $300 printer... I'd ask questions of them.
i cant get anything to print. Nothing sticks to the plate.. I'm using the stock settings..
I am wondering if you can show how print with wifi
Have you got any links or advice for getting the Resin. As due to this video I'm gonna grab the Helot One via the link you provided. However how to I go about getting the Resin itself in Aus? Can I use any 3d UV Resin, or stay on brand?
Creality resin is solid, I usually just buy Elegoo resin as it's a good price on eBay and has never let me down.
I was thinking about getting a printer for stuff like my world eater chain axes is there a specific place that you can download the files from
My mini factory, thingiverse, lots of places to go find model files, they are very easy to aquire.
I saw that they offer a larger one as well. Say for example I want to print a Rhino or a Land Raider. Would this specific printer be the right size for the job?
The bigger models definitely allow you to build much bigger units, and this wouldn't do anything bigger than a rhino, even then, you would want to print any rhino in this in multiple bits as the rhino would barely barely fit a side onto the build plate.
@@TheOuterCircle Yeah that makes sense. Print it off in smaller parts, then assemble. Be interested to see how these would go. Much cheaper to setup than my Stepcraft CNC was haha. Thanks for the reply Macca!
My 3d printer is only printing flat pieces I have halot-one like you. can some one give me a solution
Hi does it work with lychee slicer?
Whats your print rising height in print setting
Wich one is better this one or the Creality LD-002H or the anycubic photon mono or Elagoo Mars 2 pro
Hi Marcel,the Halot-one light source is an integral light source. Compared with the parallel light source(LD-002H), the uniformity of the light of the integral light source is increased by 10%-15%, which can make the printed model more accurate.
My brother got a Halot-one and he is kindly letting me use it for time-lapses for my channel, but when it came today, the LCD screen that projects the UV was cracked in the corner! Is that something to be worried about? IT's just a small crack about the size of a hair.
I'd talk to them and try and get a new screen sent out, or a new unit if it's brand-new from them, as it's going to cause issues down the line.
@@TheOuterCircle Thank you for the quick reply! It just came in today so I can definitely get a new unit.
Which slicer did you use and what were your settings?
No matter what I try, I'm always getting failed prints with the Anycubic grey resin.
I use Elegoo resin, and I’m using the stock slicer “Halot Box” it came with, which I updated when I installed it. The stock settings are perfectly adequate, namely as I’m trying to create content which anyone can use out of the box.
@@TheOuterCircle Nice, thanks for replying! Did you figure out what's the settings screen for in the printer? You can configure a bunch of stuff, but it doesn't affect the prints, so... What's the point?
@@LuisHansenNH depends on the firmware version you’re using, also gives you some small tweaks on the fly. I haven’t needed to touch it in all honesty and I’ve produced some fantastic prints, I’ll have a revisit on the Halot coming in a couple of weeks where I show some of the products produced and talk about pros/cons after using it for some time.
Hi Luis, thanks for your support, it is recommend to use the default setting. if it did not work ,please increase the bottom exposure time and send email to halotsevc@creality.com with your question, we will offer you the solution.
@@halotservice6739 look at that, can't beat that sort of service! we're delighted with our purchase of one of these.
You mentioned the anycubic photon mono 4k? Which one do you like better? The Creality or anycubic ?
Tough call, I think I've had better results with my Creality systems over time. I've been weighing them against one another for a while now.
Huh ive just been looking for 3d printers and advice
What happens if you did all that and that whole time nothing was being created how can I fix that problem
Often the build plate isn't adhering, so you need to grab it out, sand it with coarse grit paper, and put it back in. After that, you can also try simply changing the resin, it's often the biggest offender. If you use a clear resin, you can often watch and see the UV light to see if it's curing correctly on the screen.
May I ask what resin do you use as I don’t know which to buy.
I mostly use Siraya Tech fast cure grey.
does that figurine at the end not have hands
Silly question is it a 4k resolution printer?
It's 2K
how is the smell ?
Printed Wargaming might be a prosperous market in the future.
already is tbqh, just stick in the muds who still want to pay 10x the price for worse minis. Plus with a bit of 3d cad design effort minis like never before are showing up.
It's a good printer! I just wish it had a build plate the same size as the Photon Mono.
Wait a second mate,you used grey resin and you show us clear green so what happened with the first print did it failed or what are you getting this printer for free to make review or what ?
Printer goes brrrr 😋 I pre ordered the Elegoo Mars 3 4k two weeks ago I am very excited it was the same price as the Mars 2 Pro (they are now cheaper) 3D printing is dirt cheap these days. I have got on to several Paterons for minis I mostly like to paint and do some Dioramas, but I will be playing One Page Rules as well pretty soon when it comes.
I was thinking about the Elegoo Mars 3 4k, Does it function the the one Macca just reviewed? Easier /harder to use? Is it better than this creality one? Sorry for the Rapid fire Q&A. lol
@@FamousJX it's cool it's not out yet so not sure how it will be in reality it is also my first one. But reviews for the content of it are positive with how it performs 😁 big build plate, monochrome screen (better designed for 3D printers) leveling on all 3D resin printers are pretty much the same, same goes with clean up etc... All can use any kind of UV resin for 3d printers but might need to fiddle with settings. Most use the same branded resin as they have the settings there for you ready to do 😁 and of course you can mess around with them to try to get faster printers, smaller layers (smoother finish but takes longer) look up some reviews there are a handful on here. Uncle Jessy is good for this stuff as well.
@@yagsipcc287 Very nice, Thank you for the info. :)
@@FamousJX no worries bud. We should all help eachother 😁 too many Bootlickers out there. Ha
today it came today i set it up today i testprint my first model. i am getting nervous
Can you make a video where you paint one of your creations please?
I don't tend to show a lot of tutorials on CZcams, I do a bit of showcasing on instagram, but I tend to keep the two quite separate to one another.
Bought one of these at Micro Center for 100 bucks today. At long last I can begin work on my tiny goblin army
Can you reuse the used resin?
The stuff from the vat, yes, it needs to be filtered back into the bottle before you do.
Do you have a discord?
I don't get why you took the protective film off then put paper in its place. Just use the plastic film then take it off after 🤷🏻♂️
So it's $25 for 250 ml of resin. How much resin was used up for that single dude? A.k.a. what is the estimated price of printing a single model, the printer cost excluded?
well he is using the cleaning func wrong so dont count that w8st so its about $1 give or take 50 cent for the rest of the parts if it needs them (guns hands holding whatever and a base) and you dont have to use their resin and you can get it for $20
No it isn't. I got 1000ml or less than 35$US. That's for good quality Elegoo ABS style resin as well.
@@shanepatrick4534 the siraya tech fast is much better for around $20 bucks 500ml
@@warshak11 Cool I'll try it out.
I said $25 for 500mL of Elegoo resin, and that's in Aussie $$$ with next day delivery. I usualyl buy it when they offer 4 for the price of 3.
I was thinking about buying this printer but was wondering what features it doesn't have since it is only around $160
It's a 2k screen, not a 4k, that's about the worst of it. It has wifi connectivity and updating, it has a good build plate and easy to use interface. On release they didn't raise out of the vat on pausing the job, that was probably about it.
What are the chances of 3D printing an imperator Titan in this thing ?
Can definitely be done, I do have a larger format printer from Creality I haven't really shown off yet which I printed a 28mm Armiger + a bunch of extra stuff in a single run.
@@TheOuterCircle fantastic
Would you be up for giving it a go ?
@@Southpoint2019 I'd be tempted once my time frees up in another month.
The exist resin is reusable?
Excess resin is reusable, so long as it's filtered.
Main issue with these and also normal 3d printers is alot of people buy them and do not have the correct air circulation...will just lead to knackered lungs and prob cancer later down the line
yeah...don't use clear resins for reivews can't see bugger all on it
Amazingly the halot one is more reliable than my saturn, I should refund my saturn and buy 3 more halot ones.
I really love it, mine hasn't skipped a beat and I've made a LOT of miniatures in it. I just dropped some money on an LD-006 from creality, after that I might look at a Halot Sky because people REALLY rate that.
@@TheOuterCircle Question for you, apparently the machine should be supported by Lychee, but if you go into lychee there's no settings you can actually change. Is the only way to change exposure and what not, via the screen?
@@biggrundo6667 I haven't tested it with Lychee so I honestly don't know the answer
@@TheOuterCircle ah, is there a way to change exposure times and what not through halot box? I only manage to change them on the printer.
You can change these settings in Lychee after adding a resin profile
i have been breathing fumes of resin and i have not used a single glove when touching resin. am i still alive? who knows. i may be neither dead or alive
Schrödinger Josh LOL - Use a mask (not the one in the video, it is useless for that), and wear gloves, it won't harm you and could save you a hard time :-)
The slowest resin printer on the market ! Damn slow ! Except when it dumps in the VAT to splash resin out.
You lost me when you said the scraper tang wasn't centered properly
do not slide the vat on the screen man
I didn't, there's pins which hold it up up and locate it when you move it, at least on my model, so it isn't touching the PETG film against anything nor anything against the screen.
@@TheOuterCircle oh ok my mistake i know it can damage the screen easily
That mask is useless. BTW. I have one of these on order.
Dude acts like resin is worse then uranium
halot {t}: dead Hungary - English 😂😂