How to Replace Passenger's Side CV Axle 2003-2008 Toyota Corolla
Vložit
- čas přidán 6. 04. 2023
- Buy Now!
New CV Axle Assembly from 1AAuto.com 1aau.to/ia/1AACV00048
This video shows you how to install one in your 2003-2008 Toyota Corolla. A CV axle has flexible joints. Often, these joints wear out, or seize from contaminants due to the protective boot tearing open. A worn joint is prone to breakage, or other hazards. If your vehicle needs a new CV axle, install a quality TRQ axle that is engineered to your vehicle’s specifications.
This process should be similar on the following vehicles:
2003 Toyota Corolla
2004 Toyota Corolla
2005 Toyota Corolla
2006 Toyota Corolla
2007 Toyota Corolla
2008 Toyota Corolla
Tools you will need:
• Pry Bar 1aau.to/oP6/1AXAA00020
• 17mm Socket 1aau.to/objP/1AXAA00015
• 30mm 12-Point Socket 1aau.to/oab/1AAST00002
• 1/2 Inch Impact Gun 1aau.to/oqW/1AXAA00252
• 3/8 Inch Impact Gun
• Torque Wrench 1aau.to/oaxC/1AXAA00044
• Anti-Seize Grease
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - Auta a dopravní prostředky
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
All goods but you forgot to punch in the side of the axle nut.
Thanks for the helpful videos. Now if I can only get my hands on a car lift…
Thank you very much SIR,I'm Roger from philippines.MORE POWER AND GOD BLESS
AWESOME video thanks for posting
Awesome video,thank you,can you make more Toyota videos , specially diagnostic and wire diagrams
Great video, thanks!
Excellent 👍
I got shock how u literally place a new CV Axle that has different parts and modes than the Original one, I was close to return my product, but then I wanted to come here confirm.., and yes.. u do exactly that !, u put a different looking CV Axle and still is the right one that fits in
Question i notice that the axle you removed had a balancer on it , why didnt the new one have a balancer will that be an issue later?
Is this basically the same process for the 2006 camry
Hello, the new CV axle doesn't show a counterweight, affects functioning?
Amazing video. It will still take me six hours laying on the floor and cussing while trying to pop those inner splines loose from the transaxle.
+@sibco96 Thanks for the feedback! 1aau.to/m/Shop-TRQ
Do you have to replace the axle nut or can you reuse it?
I just replace both front cv axles on 2011 Corolla and it seemed like everything went good but now I’m hearing a “whomping” sound as I drive and when pulling into reverse it makes a clunck sound. Anybody got any ideas on what this could be?
So Easy 🎉
I just put in new trq CV joints and there's still noise it's slapping back and forth a little bit.
Was a abs or non abs
I am attempting this job on my 2014 Corolla, and am stuck on removing the axle from the transmission. I don't have access to a lift, so having to maneuver a pry bar under the car is proving very difficult. I may have to have my car towed to a shop. I'm in over my head a bit, plus I'm absolutely exhausted from laying down and prying and hammering. I feel dizzy and I'm shaking. I think I'm in trouble.
What happens if the seal is bad
Nice. Now if I just had a lift in my garage
It was a Friday when you did this huh?
What? 66 Newton?
You guys keep taking away key aspect. You need to drain the trans fluid before doing this.