not everyone know about this SIMPLE Mig Mag welding technique

#welding #construction #magwelding #migwelding #fewpeopleknow #weldingforbeginners #misgstickwelder
not everyone know about this simple mig mag welding technique

[@seadkadic]

congratulations for a job well done, your teacher must be proud of you

[@user-zo6ut3cp4z]

सर मुझे पता है आप बहुत अच्छा व्हिडिओ बनाते है व्हिडिओ के साथ जानकारी बहुत अच्छे

[@blitarwelding]

good job

[@arneminderman3770]

Great!!

[@mikebryan544]

So i notice your only nudging the bead forward but then coming back and letting it fill out. I think i stay too much in the front🤔 will try thanks

[@wacotom3729]

3lagige kehlnaht ist eine Prüfungs naht.

[@jesuslongoria8891]

Esta soldadura es de 12mm pero lleva tres pasos es uno de uno de 45 uno de de 35 y el otro es de 40 para poder hacer el cordon de soldadura de 12 mm con 3 pasos

[@danielszymanski-jw5kq]

Pick your hand up off of edge of piece let nozzle drag slightly over the surface! You get a more consistent angle! Fill in your craters some ! Back fill it! Looks good though

[@VypaGaming]

It looks like a nice weld but is 26 volts more on the cold side for 15mm? Id give it at least 28 volts

[@bkh5746]

Its too hot man it will crack..

[@A3ternusA]

​@bkh5746 I usually do 28.5 volts and even with a 5mm plate it doesnt crack

[@chrislayton4213]

30 volts 312 wire speed 1.4 wire

[@im-welder]

❤❤❤❤🎉🎉🎉

[@muratkaz5373]

Kaynağın bittiği yerde krater oluşuyor , ayrıca kaynak boyunca kaynağın kenarlarında yanma çentiği var.

[@yarobanasiak]

Słabe te lico na potrójnym, nie wiem jak z boku to wygląda ale z przodu widać szczelinę miedzy ściegową. Pozdrawiam

[@karlkarle2101]

Ist das ein Video um zu zeigen wie man es besser nicht macht?

[@Patrick-ko9lp]

Genau das dachte ich mir auch 😅

[@wacotom3729]

Dann lass die Finger vom schweissen. Das ist eine 3lagige kehlnaht..

[@dewayne2189]

Why do you hold your nozzle so far away I run my little closer

[@pacor6712]

I learned that in second grade dude

[@shakaylascott1110]

Sure ya did

[@jordanwing9594]

Well people gotta start somewhere, cant expect them all to be asshats like you brother

[@user-wc4qp2qj1u]

Надо ржавый варить где не подлезть не почистить

[@alicanwlf9998]

Sağdan solamı çekilir kaynak sağdan solamı

[@wacotom3729]

Eine stechende naht hat mehr einbrant.... Ok.

[@user-wc4qp2qj1u]

Так первокласник сможет

[@babilonspaces.5844]

Insomma.

[@user-vm5vd1dr4f]

А зачем? Зачем водить туда сюда,если можно просто вести

[@user-zo6ut3cp4z]

सर mig welder मारता

[@babilonspaces.5844]

Colatura....

[@Deichjunge65]

Endkrater übereinander ist ein Grober Fehler, man ordnet die Endkrater versetzt an.

[@sammy6100]

Absolutely no need to do this.
Keep your wire in the centre and follow the two adjacent lines to get an equal finish

[@user-lo4gs1yw7t]

Чтото тут не так

[@user-um9bf6hn7p]

Всего навсего катет 12.

[@user-zo6ut3cp4z]

मुझे आपके साथ काम करने का मोका मिलेगा

[@bkh5746]

Too hot

[@markvincentsalandanan5970]

Goodday sir. May I ask u what is the voltage if 10mm the plate?

[@johngrisham4437]

Sbagliato

[@xxxewgen]

фуфло сварка,нужно было либо с зазором варить,либо фаску снимать

[@user-zo5bm8se3w]

Зачем тратить время на фаску и зазор ,когда можно добавить ток

[@xxxewgen]

@@user-zo5bm8se3w это потом просвещенцам рассказывай

[@DonCorleone640]

Einbrandfrei 😂