722.6 Mercedes Transmission Conductor Plate / Valve Body replacement
Vložit
- čas přidán 22. 07. 2024
- Playlist with All the Videos I made about this Car :
• W220 Mercedes S 320 Co...
Before just replacing the valve body/conductor plate the best is to inspect it , do a diagnosis and analyze any signs of failure . So in this video you will see important things to know if you wanna fix the 722.6 automatic transmission from this Mercedes S 320 w220 . Of course the same 5 speed transmission will be available on many other Mercedes models .
Disclaimer :
This youtube channel :"doit_vehicles " can not guarantee that this information suits your car . "doit_vehicles " assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk
#722.6ValveBody..ConductorPlate - Auta a dopravní prostředky
Wow, just great! More please. Very solid portion of knowledge
good video, clear and helpful, thanks
HELLO.....thank you for your superb video....same problem after changing my plate with Febi-bilstein and Solenoid joints etc...Code P0730 on my Autel and in addition the Mercedes techs tell me that they can no longer access the settings with their Tablet..
I am disgusted by this SLK 230 from 1996 which is costing me an arm and a leg... thank you for your advice.....Continue...
Hi what happen when the clutch solenoid its bad????
hello
I saw this video today and tried to drive after replacing the transmission oil and transmission plug, but the car doesn't move... The shifter moves from p to R to R to N and N to D, but the car doesn't move.
What's the problem
Thank you🙂
I have the same vehicle. We renewed the turbine valve today, but there is a noise when putting it in park and taking it out. This could be the reason. We also renewed the oil. Do we need to adapt it?
The diagnistic computer says "Slip" .Also, there is big delay in shift between 1st & second shift.
Thank you
Question: Do you like your Foxwell Scanner ? Im thinking of getting the new Autel Maxisys Ultra 2022. Since most of the cars I own are Mercedes and BMW and Porsche VW. My other friends and mechanic have been using the matco's launch. But they are getting a new one. I have the SnapOn Solus but it doesnt work as good as the Matco Launcher. But I think Autel from others YT reviewers are better. This is first time Im seeing Foxwell scanner. Just asking your opinion why you chose Foxwell.
hello, after taking the voltages on the round pin of the board
everything is good except the 11 which does not give me 1.96 volts etc... each time with the 11, any ideas please???? CLEARLY HELP!!!!!
Good
Stimmt es, dass nach dem Austausch des Sensors eine Programmierung erforderlich ist?
Did that resolve the issue?
Did you put in a mercedes magnet A169 3710003 at bottom of oil sump before boxing up the transmissiom. I would put in two such magnets for next oil change. It does looks like iron metal dust particles are fine enough to past thru the oil filter. How about the two small round mesh filter inside the valve body? Any accumulated debris such that more that 20% of the mesh is covered up?. Regard.
Not a bad idea , the problem is that the aluminium particles are more common ; And maybe it's better to change the filter more often ?
good video my friend ! my goddamn mercedes always fucking with me . It has a P240C code. The electronic module in the gear selector fails. very annoying :D
Hey definitely late but having a problem when turning left (only on left turns) the car slips out of gear Mercedes is thinking it’s the valve body but I’m unsure if that’s the problem as it only happens when turning one direction. Hopefully you have any info on this matter!
Low on trans oil ?
Can you give an advice please,why when i put in reverse the car have a big vibration?
If it only vibrates in reverse and not in drive , try to observe under the car when someone puts it in reverse and check for vibration on the transmission . if it doesn't than it's something internaly . If it does than it's most likely the mounts
good video
thanks
hello Sir. i have a 2004 Mercedes e302 w211. i have an issue at the morning only cold start the transmission shudders but when the car gets to normal temp it ran perfect do have an experience before about this issue thanks a head
In this case I would check the live data first ( might be the engine ) and than I would check the fluid quality ;
@@doit_vehicles Thanks Mate
what the data list i have to watch u think?
what sizes are the o-rings on the solenoids?
Hard to tell now , but a O ring kit might be a solution. I've seen once some replacement kits online with the correct sizes
Great video, I also have the transmission shaking simptome (from 2nd to 3rd gear) so I will change the conductor and the orings. I'm kind of pissed off that I didn't do this sooner as I knew this will eventually be a issue.
Where are you from?
Did you manage to fix this? And how please?
@@thepio14343SWEG Hi, I didn't solve the problem, even if I changed the conductor plate.
@@xavierrochaschange the valve body it's the issue.
Just another Defective MB part. Mine has issues at 10,000 miles. Will cost me 2-3k to have fixed. MB has the worst parts. Will never buy another MB..jc
lol, 10,000 miles? the 722.6 hasn't been used in MB cars in 10 years so how would you have so few miles? and a replacement valve body doesn't cost 2-3k either. I think you're either very confused or just full of it.
I have 722.6 transmission problems not shifting staying in 2-3 gear. How do I know if the conductor plate is bad? Or the valve body or solenoids need replacement?
sounds like it's in limp mode so it's probably a bad conductor plate
but you should scan the car and see what comes up to know more...