Hey I had a question, wondering if you are experiencing this too. I noticed when using the auto catch, it doesn't push the button until maybe halfway through the second green light up. I was kind of annoyed by it but noticed it seemed to behave the same way for you. However I noticed later that if the plus + is plugged in for charging, it pushes on the first green light up. Have you noticed similar behavior?
I have just finished modifying mine, But I used a reed switch up by the top button (around 11oclock) I also got a tiny vibe motor from a mobile phone and put that in where you have you switch, the vibe is much better with a smaller motor. I have found tho that every so often when I switch it into (auto mode) the motor will vibe untill I switch it off and back on.... Thanks for your video It was very helpful.
Hi, Thanks for sharing, I have followed you to modify and can auto catch for two days, but right now I found it is out of battery. And try to charge it, but it didn't work, do you have any idea to troubeshoot ?
Hi I've done this mod but I think my button isn't working properly. When I press the button there is no feedback which leads to the auto throw mod not working. Any ideas what I did wronf
Nice work, I have a question, though. I'm only using it for Pokemon Sleep to track my sleep. My problem is that I'm almost always pressing the main button by accident. I want to use the switch to disable the main button entirely and re-enable it. Is it possible? Is the Main Button connection inside the flex cable? where should I cut the connection? I don't mind to scratch the mainboard.
No. The button is surface mounted. It has 4 legs (2 positive 2 ground i believe). If you cut the legs it would be useless. You could try to do different button to connect to the same testpoint that i am connecting to in the video, but i wouldnt do that. I have a clear plastic case on mine, that is raised higher than the button and accidental button presses almost dont happen. Watch my latest video, you can see it there. I bought it on aliexpress.
@@ma3x558 thx for your answer. I got it working with scratching the connection through the board on the backside and solder the switch between leg and test point. Now I can sleep without worrying pressing the button by accident. Your video was very helpful for disassembling and using the solder points👍
@ma3x55 The problem you are discussing in 5 minutes can be turned off by holding the white button for 3 seconds. Sleep mode can be turned on using the Pokemon Go Plus+ charger. The switch is then unnecessary.
Sorry don't know if it ever come out 😅 but I can tell you that to me plus+ with the mod is worth the money. It really depends on your style of play and how hardcore about the game you are. Reconnect without the need to press the autocatcher is a really nice bonus that I got used to. I stopped playing pokemon sleep after I got my 5 snorlax so I can't recomend it for that. I only use autocatch with great and ultra balls during events but it is also a very nice upgade. Compared to some autocathers, plus+ needs to be charged more frequently and is only for one account, but that isn't very important to me. So overall I am satisfied with it 🙂
@@ma3x558i am new in the field. Can you tell please sides of powerMon Plus. Are there a different ones which has the same functionality like pokemon Go plus + but with bigger battery/ multiple users? Do you know that ?
Is it possible to get out of the loop (for example by holding the main button for 3 sec) if I don't use a switch? Can't find it anywhere locally with the right dimensions...
Čau, takovej dotaz, k čemu je tam potřeba ten switch? Pochopil jsem, že si přepínáš auto catch, ať se ti to nesekne do loopu nebo? Proč bych prostě nepřipájel jenom kabel? :D díky
@@ma3x558 No nic, tak jdu asi koupit switch 😄 díky za tutorial 👍 doteď jsem používal gotchu, která je taky super, ale včera jsem koupil plus+, akorát jsem ustřihl drát na vibrace, cuz to je hrůza :D ještě dotaz, případně kde jsi koupil ten switch? Nemůžu najít žádnej "přepínací" spíš jen tlačítka a spínače :D
Can the vibrator be removed completely or is that black wire necessary? I've already snipped the red and black wire for the vibrator as a quickfix to get rid of it...also, anyone know if 3mm switch sits flush on the device or would it be safer to go with 4mm? Edit: does this also autospin stops or just autocatch?
If the black wire would be soldered to the third switch contact and the red wire would stay conected..., while the new cable that is connected to the solder point of the black wire is connected to the middle contact of the switch. Would that result in the vibration working when switched to manual?
@@ma3x558 I can confirm that it works. The only thing to watch out for is to switch it to manual when the pogo++ is not connected. Otherwise it will start sleep repetedly
If I'm understanding this correctly, the first switch contact would run the wire to the test point of the button? So all three contacts are taken and the device would vibrate in manual but not in auto catch mode?
Correct, switch point 1: new wire to connect to the white button plate (like in the video) 2. connect to new wire that is connected to solder point of the black wire 3. Connect with black wire @@NathanHampton
The loop issues making me second guessing if i should mod my pogo plus plus now :(. I was hoping for a seamless experience where you just turn it on and thats it.
cz I have a macro running that automaticly presses that button on the screen to reconnect it. Would this still work without me pressing a button fysically
Hello, I would like to ask you. Is it possible use switch for switching between autocatch and vibration? In this case i dont understand, why you cut off red wire, and let black one Why you let vibrator inside of device? Is it possible this setup?: Send black wire from board to switch to middle pin, another pin connect to button, and the last one pin connect to black vibration wire. And let the red one connected to the board? Then I expect two modes - autocatch without vibration and manual catch with vibration
Ahoj. Nad tymto som rozmyslal a predpokladam ze by si na to potreboval troj-polohovy switch alebo dva switche. Ale neskusal som. Motorcek nevyberam aby sa nestratil a dalo sa to dat do povodneho stavu.
@@ma3x558 jaj, mi tu zmizel koment. Já si myslím, že 3 polohy nepotřebuji, protože chci dva módy. Originální - tzn manual s vibracemi a modifikovaný - autocatch bez vibrací. Předpokládám, že aby vibrace fungovala, tak musí být zapojený červený i černý drát. Takže pokud červený nechám zapojený a černý z desky půjde pouze do switche na středový pin, tak ze switche můžu natáhnout jeden černý na tlačítko a poslední pin napojit na vibrace. Takže když přijde signál, tak půjde vždy přes switch buď do tlačítka, nebo do vibrací. Když půjde do vibrací, tak když stisknu tlačítko, tak signál bude zaslepen ve switchi, takže půjde jen tam kam má. Zkusil jsem udělat nákres, ale nevím, zda mi youtube dovolí jej přiložit (pardon za kvalitu - elektro jsem kreslil naposledy před 15 lety 😀)
@@martinnavratil3265 ano myslim ze by to malo ist. Ak sa ti to podari daj vediet. Budm jedno plusko robit buduci tyzden ale vsetci chcu vzdy vibracie uplne odpojit
@@ma3x558 na první pokus to funguje dobře 🙂Chvíli mi zatrnulo, když jsem připájel tlačítko, tak začal dávat hlášky, které jsem ještě neslyšel, ale asi to bylo jen vybitím. Kdyby se objevil nějaký trouble, tak to sem napíšu 🙂
pretty sure I shorted something somewhere. Top button blinks red indicating low battery. But only connected to charger. When it's not plugged in I get no function at all..
And thanks for the tipps with the switch. With Amazon I always habe to order 150 Switches in Germany. It costs about 5 eur but what should I Do with 150 pieces?😁
@@christopherclemens2596Geh lieber in einen kleinen Elektroladen. Dort findest du einzelne Schalter auch für ein paar Cent. Sparst dir dann sogar noch die Versandkosten
Some people are suggesting that Niantic will crack down on non-genuine catchers, now they have a new one, so I'd be cautious buying an alternative for a few months.
@@martinmedricky8748 Ok so in summary you cut the red wire from the virbrator You sold another cable to the same spot as the black cable from the vibrator to the switch The other cable from switch to the 3rd spot on the front board and you’re done that’s all?
@@ma3x558 but what about the sleep mode issue? Do you have it every time you disconnect? Meaning everytime you want to connect it you have to switch the switch?
I said in the video that no. I don't want to handle shipping and I don't know how much I would need to ask for it. But if someone is really desperate we can figure something out.
@@ma3x558 I understand. It's only because I have bad eyesight (stargardt disease)which is why I can't do small detailed mod. I rely on the auto catch because sometimes it's too difficult to play
I have the loop issue everytime I a) lose connection (try walking out of range from your autocatcher to confirm please) b) switch into auto mode after manual disconnect (I think that's mentioned in the video
![Modifying Pokémon GO Plus+ [Mod Tutorial]](http://i.ytimg.com/vi/MN6X_0TaZPg/mqdefault.jpg)
![Modifying Pokémon GO Plus+ [Mod Tutorial]](/img/tr.png)
Hey I had a question, wondering if you are experiencing this too. I noticed when using the auto catch, it doesn't push the button until maybe halfway through the second green light up. I was kind of annoyed by it but noticed it seemed to behave the same way for you.
However I noticed later that if the plus + is plugged in for charging, it pushes on the first green light up. Have you noticed similar behavior?
I have just finished modifying mine, But I used a reed switch up by the top button (around 11oclock) I also got a tiny vibe motor from a mobile phone and put that in where you have you switch, the vibe is much better with a smaller motor. I have found tho that every so often when I switch it into (auto mode) the motor will vibe untill I switch it off and back on.... Thanks for your video It was very helpful.
Hii, did you just use a standar DC mini motor for phones?
thank you.
Hi, Thanks for sharing, I have followed you to modify and can auto catch for two days, but right now I found it is out of battery. And try to charge it, but it didn't work, do you have any idea to troubeshoot ?
Díky
I’ve seen people selling these modified version online is it worth it to buy one? I don’t have the skills to modify it myself or the tools
Hi I've done this mod but I think my button isn't working properly. When I press the button there is no feedback which leads to the auto throw mod not working. Any ideas what I did wronf
Nice work, I have a question, though. I'm only using it for Pokemon Sleep to track my sleep. My problem is that I'm almost always pressing the main button by accident. I want to use the switch to disable the main button entirely and re-enable it. Is it possible? Is the Main Button connection inside the flex cable? where should I cut the connection? I don't mind to scratch the mainboard.
No. The button is surface mounted. It has 4 legs (2 positive 2 ground i believe). If you cut the legs it would be useless. You could try to do different button to connect to the same testpoint that i am connecting to in the video, but i wouldnt do that. I have a clear plastic case on mine, that is raised higher than the button and accidental button presses almost dont happen. Watch my latest video, you can see it there. I bought it on aliexpress.
@@ma3x558 thx for your answer. I got it working with scratching the connection through the board on the backside and solder the switch between leg and test point. Now I can sleep without worrying pressing the button by accident. Your video was very helpful for disassembling and using the solder points👍
@ma3x55
The problem you are discussing in 5 minutes can be turned off by holding the white button for 3 seconds.
Sleep mode can be turned on using the Pokemon Go Plus+ charger.
The switch is then unnecessary.
Have anyone tried this? Does this really make the switch unnecessary?
Been wondering this myself, any follow ups? Can't seem to find a switch with the right dimensions anywhere locally...
Can u say when the 3rd Video will come? Wanna know if its worth the money for the plus plus
Sorry don't know if it ever come out 😅 but I can tell you that to me plus+ with the mod is worth the money. It really depends on your style of play and how hardcore about the game you are. Reconnect without the need to press the autocatcher is a really nice bonus that I got used to. I stopped playing pokemon sleep after I got my 5 snorlax so I can't recomend it for that. I only use autocatch with great and ultra balls during events but it is also a very nice upgade. Compared to some autocathers, plus+ needs to be charged more frequently and is only for one account, but that isn't very important to me. So overall I am satisfied with it 🙂
@@ma3x558i am new in the field. Can you tell please sides of powerMon Plus. Are there a different ones which has the same functionality like pokemon Go plus + but with bigger battery/ multiple users?
Do you know that ?
Is it possible to get out of the loop (for example by holding the main button for 3 sec) if I don't use a switch? Can't find it anywhere locally with the right dimensions...
If you are is USA I can give you switch for free as I have extra.
curious... can the functions of the pogo++ be used on a pc with emu and no device? new to all this and using pgsharp payed version
Auto catch with ultra ball and spin pokestops?
Čau, takovej dotaz, k čemu je tam potřeba ten switch? Pochopil jsem, že si přepínáš auto catch, ať se ti to nesekne do loopu nebo? Proč bych prostě nepřipájel jenom kabel? :D díky
Ahoj. Ano presne pre ten loop. A taktiez ak pouzivas apku sleep tak vtedy to musis mat vypnute.
@@ma3x558 No nic, tak jdu asi koupit switch 😄 díky za tutorial 👍 doteď jsem používal gotchu, která je taky super, ale včera jsem koupil plus+, akorát jsem ustřihl drát na vibrace, cuz to je hrůza :D ještě dotaz, případně kde jsi koupil ten switch? Nemůžu najít žádnej "přepínací" spíš jen tlačítka a spínače :D
I have 3mm tall switches, do you think it is worth buying the extra mm switches?
Probably not. You should be fine. But if you use a case like me then 1mm helps so it sticks out more
is that powerman plus worth buying still??
브로 안녕 한국에서 포켓몬고를 하고 있습니다.
포켓몬고플러스+ 2개를 구매하였고, 영상 참조하여 스위치연결, 진동제거, 볼던지기 자동 성공하였습니다.
수면 피카 소리가 듣기 싫타면 어두운곳이나, 뒤집어 놓으면 발생되지 않습니다.
You sell these?
Can the vibrator be removed completely or is that black wire necessary? I've already snipped the red and black wire for the vibrator as a quickfix to get rid of it...also, anyone know if 3mm switch sits flush on the device or would it be safer to go with 4mm?
Edit: does this also autospin stops or just autocatch?
This accessore was made for walking, If you are goint to use it "sitting" you will be dissapointed and not because of vibrator.
hi tedibear do you found the answer for this? i already snipped the red and black wire as well for the vibrator. does it stlil work?
Yeah, it works fine without the vibrator@@JC-cb6he
If the black wire would be soldered to the third switch contact and the red wire would stay conected..., while the new cable that is connected to the solder point of the black wire is connected to the middle contact of the switch. Would that result in the vibration working when switched to manual?
I assume that yes it would. But can't confirm
@@ma3x558 I can confirm that it works. The only thing to watch out for is to switch it to manual when the pogo++ is not connected. Otherwise it will start sleep repetedly
If I'm understanding this correctly, the first switch contact would run the wire to the test point of the button? So all three contacts are taken and the device would vibrate in manual but not in auto catch mode?
Correct, switch point 1: new wire to connect to the white button plate (like in the video) 2. connect to new wire that is connected to solder point of the black wire 3. Connect with black wire @@NathanHampton
@@lw6953do you have a wiring diagram for this?
The loop issues making me second guessing if i should mod my pogo plus plus now :(. I was hoping for a seamless experience where you just turn it on and thats it.
get the duomon 2022 version and save yourself the headache
@@Ms7midodoes the duomon auto throw great/ultra balls?
I cant get mine to sit in place very well. Advice? Im using electrical tape and sticky tack
I pushed the speaker under the switch and it holds it in place without anything else.
can you get out of the loop by simpely pressing the pokemon go plus button on the app, so it will connect again to the pokemon go plus +?
cz I have a macro running that automaticly presses that button on the screen to reconnect it. Would this still work without me pressing a button fysically
Hello, I would like to ask you. Is it possible use switch for switching between autocatch and vibration? In this case i dont understand, why you cut off red wire, and let black one Why you let vibrator inside of device?
Is it possible this setup?: Send black wire from board to switch to middle pin, another pin connect to button, and the last one pin connect to black vibration wire. And let the red one connected to the board? Then I expect two modes - autocatch without vibration and manual catch with vibration
Ahoj. Nad tymto som rozmyslal a predpokladam ze by si na to potreboval troj-polohovy switch alebo dva switche. Ale neskusal som. Motorcek nevyberam aby sa nestratil a dalo sa to dat do povodneho stavu.
@@ma3x558 jaj, mi tu zmizel koment. Já si myslím, že 3 polohy nepotřebuji, protože chci dva módy. Originální - tzn manual s vibracemi a modifikovaný - autocatch bez vibrací.
Předpokládám, že aby vibrace fungovala, tak musí být zapojený červený i černý drát. Takže pokud červený nechám zapojený a černý z desky půjde pouze do switche na středový pin, tak ze switche můžu natáhnout jeden černý na tlačítko a poslední pin napojit na vibrace. Takže když přijde signál, tak půjde vždy přes switch buď do tlačítka, nebo do vibrací. Když půjde do vibrací, tak když stisknu tlačítko, tak signál bude zaslepen ve switchi, takže půjde jen tam kam má. Zkusil jsem udělat nákres, ale nevím, zda mi youtube dovolí jej přiložit (pardon za kvalitu - elektro jsem kreslil naposledy před 15 lety 😀)
@@martinnavratil3265 ano myslim ze by to malo ist. Ak sa ti to podari daj vediet. Budm jedno plusko robit buduci tyzden ale vsetci chcu vzdy vibracie uplne odpojit
@@ma3x558 zkusím a dám vědět. já vymýšlím jen, jak ty vibrace utlumit, ale vypínat jsem to úplně nechtěl
@@ma3x558 na první pokus to funguje dobře 🙂Chvíli mi zatrnulo, když jsem připájel tlačítko, tak začal dávat hlášky, které jsem ještě neslyšel, ale asi to bylo jen vybitím. Kdyby se objevil nějaký trouble, tak to sem napíšu 🙂
pretty sure I shorted something somewhere. Top button blinks red indicating low battery. But only connected to charger. When it's not plugged in I get no function at all..
You should have disconnected the battery..You can buy a switch joycon battery to replace it.
@@Sehyo already returned it and got a new one. Modded it successfully.
Is there any issue if i am removing speaker, too? Or can i just removing and just have no pika sound?
No issue, but it's harder to be sure that you put it into sleep mode without pika singing.
@@ma3x558 thanks. Then I will cut it of 😁
And thanks for the tipps with the switch. With Amazon I always habe to order 150 Switches in Germany. It costs about 5 eur but what should I Do with 150 pieces?😁
@@christopherclemens2596Geh lieber in einen kleinen Elektroladen. Dort findest du einzelne Schalter auch für ein paar Cent. Sparst dir dann sogar noch die Versandkosten
@@christopherclemens2596 start a plus+ modding business 😆
Some people are suggesting that Niantic will crack down on non-genuine catchers, now they have a new one, so I'd be cautious buying an alternative for a few months.
Does it auto spin pokestops and auto catch with ultra ball?
yes
Is the switch secured? Not that if you press it too hard accidentally that it goes inside the device and you have to screw it open again?
I've been using it for half a year and that didn't happen. I put the white tack around it and then put some hot glue on it.
@@martinmedricky8748 Ok so in summary
you cut the red wire from the virbrator
You sold another cable to the same spot as the black cable from the vibrator to the switch
The other cable from switch to the 3rd spot on the front board and you’re done that’s all?
@@unown_ Yes. It's easy and still works for everybody I modded it for. Sorry I answered previously using my different profile.
@@ma3x558 but what about the sleep mode issue? Do you have it every time you disconnect? Meaning everytime you want to connect it you have to switch the switch?
@@unown_ Not everytime. I used it today during CD and it didn't happen at all, but after cd I switched it off
huh, but mine just use autocath and ultraballs?
Would you offer this modification as a service on eBay?
I said in the video that no. I don't want to handle shipping and I don't know how much I would need to ask for it. But if someone is really desperate we can figure something out.
@@ma3x558 I understand. It's only because I have bad eyesight (stargardt disease)which is why I can't do small detailed mod. I rely on the auto catch because sometimes it's too difficult to play
@@ma3x558 make me one please
still need?
I have the loop issue everytime I a) lose connection (try walking out of range from your autocatcher to confirm please) b) switch into auto mode after manual disconnect (I think that's mentioned in the video
Available for purchase?
They r on ebay
What a fail niantic...lol mod of this is way better 😂