Fortress 27 Gallon Air Flow Upgrade! 33% Increase in Power!
Vložit
- čas přidán 23. 07. 2024
- A quick video on how to get industrial air flow out of a low dollar harbor freight air compressor. This will provide you with more power to your air tools.
- Auta a dopravní prostředky
You can drain the tank by using the valve on the bottom... that way it actually removes the water that builds up in the tank. Doing it your way just stores the water and leads to rust and moisture in your lines
Thank you for sharing!!!! You are a genius!
Great modification, I'll be doin that to mine for sure. thanks :))
Beautiful tip thank you
Excellent ❤
Great video! Thank you!!
Wow! Thank you!
You got 2 guages 1 is for tank pressure the other is for line pressure that can be adjusted to suit whatever tool you are using it can be replaced if it malfunctions available at home depot or harbor freight not expensive
How did you get the allen plug out of the end of regulator?
I have a dumb question. I’m using this to spray single body panels with a low cfm gun that uses 4.5 @ 90 psi. I believe this mod will help with the volume of air flow increasing the CFM right? Or is this mod useless in my case as I only need 30 psi and maybe the cfm will not be affected
What was your order of screwing things into the Tee?
not sure if im nubile or what, but u bypassed their outlets, ran it from tank thru a reg and thats it correct? their reg must be very restrictive. Home depot sells high flow fittings with almost 30% more inside diameter, i use em at the shop, they also make a HUGE difference... thanks!
Correct the regulator is more restrictive than a 1/4 quick connect. I did not use a regulator though. I ran it straight through a filter then to the hose reel.
How to lubricant this compressor
You could also buy the correct airgun that increases psi without increasing volume used
I don't understand because most tools call for 90psi
I’m gonna watch again but a common problem with my fortress 10gal 175psi is the pressure regulator knob itself keeps stripping. Twice in a year. They use soft shitty steel intentionally. I’m trying to modify the knob but sound like I can go around it?
Yes you can bypass it
@@mechanicalking Thanks! I know my question was kinda stupid since that’s what the vid was about😂 but I wasn’t sure if I could bypass manifold completely or if it was a must to have reg knob. The factory knob is essentially there so air doesn’t leak as I’ve epoxied it. I think I’m also confusing or intertwining regulator and manifold? What you have mounted to the wall is that a filter/regulator? Most of what I see protects the attachments or tools that you’re using but not necessarily the air comp itself? The 10gall fortress collects rusty water easily since the drain valve is more on the side rather than bottom. Sorry for the novel I’ve just wasted a lot of $ buying more problems than solutions. Thanks again👍
Did you try replacing the quick connect instead?
Yeah it did nothing
Isn’t the regulator capped at 90 psi, as in that is how it was meant to be used… no?
No. You can run more
Thx ,,,,
What end did you cap off? On the manifold?
You don’t need to cap it off
@@mechanicalking second question. I’ve got a leak on the short hose running from the manifold to the tank. It’s bent in such a way that it’s causing bulging at the connector to the manifold. I’m going to use your recommendation for upgrade, but trying to remove the hose from the tank is a pain. Did you have issues trying to loosen the hose from the tank?
Nope it came right off
@@mechanicalking Thanks man, guess I need a little more elbow grease.
Can you use this for painting?
Yes if you have a filter
You can use basically any compressor for painting but of course the smaller the more break the compressor would need. I would personally do this and use high flow fittings for the most air possible. If you have some money to spare you can get a 60 gallon dewalt compressor it’s like 950 at Home Depot would be perfect for continuous painting. Sometimes we have to work with what we got so painting a car in sections with a slow reducer is the cheapest.
@@fiys567lblp gun will get it done with no problem
why should we have to figure this stuff out?these companies are false advertisening...
Because they don’t want people to get the best bang for their buck essentially. They want people to upgrade and spend hundreds more. It’s like buying a car. They don’t put the best technology they have they purposefully nerf stuff.
@@fiys567 its false advertising. thats ilegal. if the tank sais 175 psi and psi isnt even 150. its false advertising.
@@rjchiedog the tank psi is 200. There isn’t a single pneumatic tool in this world designed to run past 150 psi, which is why the regulator is factory set at 150. It also reduces the run time of the compressor motor by using lower pressures.
@bfirefighter3 It does not reduce the run time because the tank pressure stays the same.
@@mechanicalking it absolutely lowers the run time. If you’re using 90 psi out of 200 instead of 200 out of 200 the motor runs half as much. Are you dense?
G3N1US💯💯💯💯💯💯💯💯💯💯💯💯👀👀👀👀👀👀👀👀👀👍👍👍👍👍👍👍👍😎
Compressor is trash, pressure switch supposedly gave out on this Compressor and even got a new replacement part per harbor freight still did the same thing. Save yalls money and get one from home depot or lowes. Unless you want to trash 400$
Dam and I just bought one 😢