Frigidaire Stove Dead Display For Oven Diagnosis and Repair
Vložit
- čas přidán 7. 12. 2020
- Call us today with you model number and we will make sure you get the right part
888-655-8569
In most cases we can get you the part the next day if ordered before 4pm central time.
---------------------------------------------------------------------------------------------------------------------------------------------------------------
Donations are appreciated you can donate here - www.paypal.me/Beardedappliance
--------------------------------------------------------------------------------------------------------------------------------------------------------------
My Camera Set Up/gear
Go Pro Hero 8--amzn.to/3lnXIcz
Go Pro Hero 8 w/Accessories - amzn.to/3eSLvdf
------------------------------------------------------------------------------------------------------------------------
Stop by our Amazon store to pick up must have tools for appliance repair
www.amazon.com/shop/beardedappliancerepair
-----------------------------------------------------------------------------------------------------------------------
Is you frigidaire range not showing any lights on the display? This video will help you determine if your control board is bad. As long as you have power getting to the board on the L1 and L2 terminal than you have a bad control board. This video will show you how to replace the board and how to check the power coming in. Hope this video helps. Like and subscribe! - Jak na to + styl
Thanks for the informative video you saved me hundred of dollars. Had a power outage today and my Frigidaire electric stove displays went blank but the oven burner worked. After watching your video I went ahead and shut the power off at the electrical panel and waited 5 minutes then turned the power back on. What a relief when I saw the digital panel lite up. Thanks again for the video and saving me money. May you always be blessed for sharing your knowledge with others. Thank you
Very good instructions for a beginner technician
I understood everything until you started talking about power issues at the end. Thanks a lot. I'm troubleshooting mine, but there are more issues than just a blank display so wish me luck! Thanks again!
Awesome video, thanks for sharing!
Thank you, panel made a pop noise, smell of burnt wires. I'm retired. Thanks for sharing your skills.
Great video, thanks.
Thank You so muchfor the eplanation of how to do this,I'll write more once we figure out if this is the actual problem and have a great week
thanks for all the help
Happy to help
I have a new oven 1 hour old. Plugged it in and the elements seem to heat, but no lights at all. This is the second one that did this.
My old range worked fine.
Never mind I fixed it. The 4 prong oulet on the wall was wired as a 3 prong, no neutral. I wired the oven as a 3 prong and it worked.
a little paper mate white out or tube of white marker paint you should add to your tool bag ! instructive video thanks !
That's genius lol I will do so!
was thinking the same ting ;)
wite out is highly flammable
Wouldn't it be better to use a hair dryer on the faceplate to loosen the glue?
informative. might want to consider a plastic putty knife
May help to use a hair blow dryer on the face plate before attempting to peel off the face plate, gently.
I was wondering if he could use white out or white paint on the back of the display where the missing paint was before putting it on the new board. Idk how professional it would look but maybe better than nothing.
My up button doesn't work on my oven temperature fells like it's broken goes straight back when I push it. Will l have to have a new panel
Hey boss, I replaced my planner after my digital screen stopped working and my oven elements stopped working. Only things that work are my stove top coils. Any idea what could cause this? Even after replacing my digital panel it still didn’t work.
My bake and broil isn't working but the stove top all works what do you think is broken
Hi I’ve got the same stove and board. Heard a loud pop and now have no broil or oven. Clock works and all burners work. And I have 120 at both terminals. Would this need a board do you think. ? It did blow the breakers and I replaced the temp sensor because the wiring was burnt and now the breakers do not trip. Any help please,, David
This is the 2nd time in 2 yrs our panel has gone out. We'll be getting a different stove.
needs new terminals causes element to pull to much current thru relay
You would think the manufacturer would put the plate on automatically, nope universal control board. You pay extra for pretty, lolol. How are you doing for finding parts? Trying to find a timer for a GE dishwasher. Plus a Genral chest freezer need door gasket. Any luck please let me know. Thanks. Nice video as always.
what is the part # on that eoc i dont have the book and cant find the model# are s# the one you used in this video is just like the one i need
If the board is bad does that mean none of the burners will work?
My issue is my indicator light stays on after I turn the eyes off. Any ideas what could cause this issue?
the burner im having a problem with heats
up on high but when I try to maintain a medium
or medium high level of heat the burner
sometimes goes off And gose on Back again itself but it doesn't stay on when i want. And there is no video on youtube about that .. please help me about this .. thanks
Okay now. Just off of what you said it sound like there in no problems. Ovens will heat and not heat depending on what temp you set it as. If you oven will heat up in say 10-20 to the pre heat temp there is nothing wrong with the heating part of it.
To be sure there is an issue do something g called the biscuit test. That is as simple as it sounds. You Cooke some biscuits following the directions to a “T”. If it is too how the biscuits will burn. If it is too cold the biscuits will be doughy in the middle. If you find an issue after that than investigate. If you do not than it can be a number of things why you cook didn’t come out right. Recipe was off, meat was too cold when starting the cook( I find myself cooking stuff longer due to my impatience on the defrost process from The freezer).
I can't get the oven door to open after cleaning cycle
So if the display panel goes out that means it can't be repaired/soldered?
I’m sure it can but I know nothing about how to do any of that. I can solder but that’s only on ex cars. When it comes to the complicated nature of these board I am lost. Replace it with a new one is quicker and makes the customer happy so I’m good with it.
Is this a replacement or repair?
What if my display screen wont display unless I give it a good bump and then it’ll eventually go back black?
Could be a loose connection on the incoming power. I have see that once. One of the wires you have power coming in on look at it and see if it is connected all the way in the connection. If it pops out a little bit that could be it. That or there is something going on internally on the board.
I may have asked you this before, but do you ever change out relays and such on boards?
If so, what do you think went bad on that stove, dlb relay?
I wish I knew how. That is over my head. If i had to guess, on this one probably a broken trace?? I bet I am way off though.
@@BeardedApplianceRepair yeah, I think is possibly a bad relay or some other component on the board.
I just removed a push button on/off switch in a GE washer.
Looks like I am going to have to remove one from a possible hood board, but it will be worth it to me for the experience of desoldering and desoldering s component on a board.
I did not have any desoldering braid, so I used small braided wire and some flux. This was my first time desoldering anything on a board.
Hope I did not damage it.
I have quite a bit more to learn in regards to checking relays and such. If I do much of it, I will get another meter so I can check them while still attached to the board.
I think they are called ESR meters.
With the multimeters I have, they have to be removed to check them.
I guess on the ones with just two contacts, you might could remove one but not sure.
ya thats the diff between $280 or $10 ... but the new world order is disposable ... *sigh
There are services that fix boards but it's just as much as a new board. They're good if you can't find one though.
How do I get my refrigerator refrigerator Frigidaire cook stove to unlock
Screen and display work, but the stove and oven won't come on.
How do you know the board is fried? You didn't check any of the caps at all. Could be a 15 cent replacement capacitor instead of the whole thing.
how do you do that?
@@mark0bravo look for blown caps on the board.
@@mark0bravo Look up a few videos on testing capacitors. Sometimes they are obvious such as being blown out or oddly shaped. You can certain tools to check them as well.
A little white out would help
wite out is highly flammable
I have this same control board on my oven and it’s beeping F11, any recommendations? The one I see people cleaning are different than this unit
$405 replacement part or $10 fix ... someone must have a solution. i read somewhere that there are a few reasons a clock may run fast. in that instance, buying a new part will not fix the problem. so im off to check the hertz(60 vs 50), check the ground, and connection points. im off grid so it could be my converter/ generator, needing a proper ground ... i guess.
If your clock is running fast yes it could be your generator. I was told from a "Wolf" tech that the emergency generator this guy had that when it ran a test each month was getting the clock off every few months. Can't help you any further than that. Good luck asshole.
Can I get a number or website were I can order a new display board for a Frigidaire gas range model# glgf389gse?
What is that large yellow square in control box called.
That's a transformer.
Frigidaire model How do you reset the control panel after the stove is unplugged?
Hello did you ever figure out how to reset this
Frigidaire Oven #FFEF3011LBG where can I get this part
Why destroy the faceplate instead of just swapping the housing? Only takes a minute to remove the boards...
Hello. Our 20yr old Frigidaire stove just died suddenly. I checked the breaker panel and not was tripped. I think the unit is dead. Should I check the fuse first rather than going to the control board?
I use a heat gun on those face plates
nice please work on your camera work
Appliance repair that doesn't know how to do component level circuit board repair? Its like a auto mechanic that fixes your engine by just buying a new engine lol.
Man, get that camera off your head. It's like being on a roller coaster. Can't watch the video.
now i dont need to go to the fairgrounds ;)
uggg ... ur not a repairman, ur a part replacer. a 9 year old kid can do that. what about the real
If i knew how to do that I wouldn't be doing this type of work I would be an engineer of some sort. I know how these things things work but when it comes to the inner workings of the control I get lost.
He repaired the stove! The thing works now! You are so d**b mr rush bayou. Same thing if he replaced a part on the board you are going to call him a part replacer also 😂😂😂😂😂😂😂 omg guy you sound like does people that even complain about their own shadow 😂😂😂😂