I feel your pain. I got a “free “ 96’ fourtrax 300 that had been sitting outside uncovered for years. Should have known better.🙄 I had to friggin break my brake hub into pieces with a hammer then had to cut through what was left of the hub with a saws all and an air cutoff tool. Then I had to slowly drive the hub off with an air chisel. I tried to drive the whole axle through from the right side like the guy on this video, but it wouldn’t budge so I said forget it. Luckily my bearings appeared to be ok. Better to stop before I break something. It’s been an ordeal.
Update..... everything went well. Easy job. Only snag I ran into was the bolts for my trailer hitch snapped. So either tap and die or new axle tubes... or maybe even just weld one. Honestly idgaf and it will probably just not have one
I have a 1993 honda fourtrax i need to de rear end work there is a tick in rearend when i am on throttle only? And my big gear in rear end pinion? I think anyways its got chunks missing i have used it for plowing last 3years plus run it alot lol great machines my question is what should i guy order for parts
I fixed it a while back rebuilt all rearend, the bearing on the driveshaft let go and the pinion bearings were pooched Big time HAHA to get that nut off the driveshaft i used square tubing no special tool needed
I feel your pain. I got a “free “ 96’ fourtrax 300 that had been sitting outside uncovered for years. Should have known better.🙄 I had to friggin break my brake hub into pieces with a hammer then had to cut through what was left of the hub with a saws all and an air cutoff tool. Then I had to slowly drive the hub off with an air chisel. I tried to drive the whole axle through from the right side like the guy on this video, but it wouldn’t budge so I said forget it. Luckily my bearings appeared to be ok. Better to stop before I break something. It’s been an ordeal.
Ha! Never thought of that heating trick for the pinion bearing. Nice
Can’t wait for preseason sled videos!
I'm about to tackle this project on my 85 big red wish me luck
Update..... everything went well. Easy job. Only snag I ran into was the bolts for my trailer hitch snapped. So either tap and die or new axle tubes... or maybe even just weld one. Honestly idgaf and it will probably just not have one
Marty McFly Working on machines can be fun. Waiting on parts and blowing money sucks right
Marty McFly It’s good having a couple units so working on one at a time can be relaxing
What size wrench for the rear double axle nuts
Does the axel come out either way or just beat it to the right?
Lol I wish it was that easy getting that bearing out😂
Ikr he got lucky. Lol
I did that same job this summer
Nice vid. All the info helps in case I have to end up doing this..... hope not...but eh..you never know. Thanks!!!
Did you build your own service lift. Looking for one.
I have a 1993 honda fourtrax i need to de rear end work there is a tick in rearend when i am on throttle only? And my big gear in rear end pinion? I think anyways its got chunks missing i have used it for plowing last 3years plus run it alot lol great machines my question is what should i guy order for parts
I fixed it a while back rebuilt all rearend, the bearing on the driveshaft let go and the pinion bearings were pooched Big time HAHA to get that nut off the driveshaft i used square tubing no special tool needed
What does that funky nut do???
R u going to the show I need a new t shit .
What size socket
What is the size or dimension exemple 2x2 or 4x4 ? of the Tubing (HSS) thx for your answer
2x2
What size tool do i need to take the axle off
I think a 32mm
Sweeeeeet
WHAT SIZE ARE THE REAR AXLE NUTS?
hmmm, I think they take a 17mm socket
eesh! what a pain!
Are you going to expo sno?
This Saturday in Montreal
If that’s a shot diff then mine is just non existent
Beautiful love u.