How to Replace Rear Bearing Hub Assembly 03-07 Cadillac CTS
VloĹžit
- Äas pĹidĂĄn 10. 09. 2024
- Buy Now!
New Wheel Bearing & Hub Assembly from 1AAuto.com 1aau.to/ib/1ASH...
1A Auto shows you how to repair, install, fix, change or replace a worn out, vibrating or groaning rear wheel bearing hub. This video is applicable to the 03, 04, 05, 06, 07 Cadillac CTS
đ§ List of tools used:
⢠Flat Blade Screwdriver 1aau.to/owb/1AX...
⢠Pry Bar 1aau.to/obF/1AX...
⢠15mm Socket 1aau.to/orX/1AX...
⢠18mm Socket 1aau.to/oeY/1AX...
⢠19mm Socket 1aau.to/oeY/1AX...
⢠35mm Socket 1aau.to/os/1AAS...
⢠Hub Puller
⢠Pipe Wrench
⢠T30 Bit 1aau.to/oe5/1AX...
⢠1/2 Inch Breaker Bar 1aau.to/ocC/1AX...
⢠Ratchet 1aau.to/owx/1AX...
⢠Socket Extensions 1aau.to/orX/1AX...
⢠Torque Wrench 1aau.to/ogy/1AX...
⢠Center Punch 1aau.to/oad/1AX...
⢠Floor Jack 1aau.to/ofy/1AX...
⢠Hammer 1aau.to/ocS/1AX...
⢠Jack Stands 1aau.to/ofD/1AX...
For More Info visit us at 1aau.to/h/Vg/
â DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
â *Watch the Video*
â *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
â *Do it Yourself*
â *Save Money*
I really appreciate 1AAuto making these videos. That is why I now buy parts from them. But there are two points in this video which may not be quite right for an SRX:
1. You will not be able to rent a slide hammer puller that will fit the SRX (because it is a relatively small 6 bolt affair), nor do you need to. A puller is not necessary, just tap the axle shaft out of the bearing. It is not hard to do, and the whole assembly will almost fall into your lap.
2. Do not remove the parking brake cable from the pawl. It is very difficult to put it back on the pawl. Just leave it there and remove the whole parking brake assembly with the cable intact.
3. - Ah, yes, one more point: Yes you can mount the ebrake assembly before you assemble the hub. It is easier that way also.
Thanks, IAAuto!
Thanks for the pointers and for watching!! +David Carlson
You guys make the best DIY Videos!
Best car repair channel. %100. Definitely ordering my hub from you due to the free knowledge
+@neonunderground5972 Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com:
1aau.to/m/Shop-1AAuto-c
This video really helped me in getting the job done, savings hundreds of dollars. The pulling of the emergency brake cable to reinstall it was a great tip, definitely going to have to put you back in a little to get it out enough to work it on the hook. Thanks a ton A1!!
This vid and the one for the fronts are killer, totally convinced me to do this myself.
Thank you for watching. Please let us know how the repair comes out! For anyone else who might be doing this job, we carry the parts shown in the video on our website. Order from us and we'll cover the shipping. Here's a link: www.1aauto.com/cadillac-cts-sts-wheel-bearing-and-hub-assembly-rear/i/1ashr00078?CZcams&ATony&CTA%20Comment
Great Presentation.
Thanks man your the best couldn't have done it without you
+Mike Sacona Thank you!
I have an 06' CTS and am planning on doing brakes, rotors and hubs on the rear end this weekend with parts I ordered from you guys. I have a question...how important is that rotor screw? Whoever owned it b4 me snapped it in half (guess it was seized) and happened it flat. I don't even know where to begin getting that small screw out...cant afford a mechanic but I know my way around to confidely do this job. This is the one thing that worries me. Thanks in advance for your help.
Great information just starting to get signs of needing this done 87,000k on my 07 CTS planning on doing in the 100k Service
+Abe Jr Thanks for checking us out. 1aauto.com
Great video! However in all these videos you make it look so easy. I WISH my CV axle would come out with just a few little love taps... The bottom bolt is a real pain! Much easier after you get the CV dislodged and pushed out a bit.
Your make some great how to videos.
+derek griffin Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com:
1aau.to/m/Shop-1AAuto-c
Nice video. Now I can appreciate, a little more, the charge the Dealer charged!!
Great video! Definitely needed the 18mm wrench. Had a hard time with rusted bolts but a torch did the trick! Also my axle bolt was a 35mm so be sure to check yours before you attempt yourself!
Great video!
Great Video ( You do Great
Work, And Great Explanations )
thank You Sir
+Sylvester Thomas Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/cadillac-cts-sts-wheel-bearing-and-hub-assembly-rear/i/1ashr00078?CZcams&CTA+Comment&F_1RzCx-tg
Be sure you dont have small pebbles trapped in there between the rwo moving surfaces. There is a pebble shelf in front of the rear wheel on the cts. I do brake clean then lube it with silicone oil spray. Thinknabout the last time your drove through construction. This has happened to me twice in 20k miles.
Hello - Is there a reason you are unable to mount the E-Brake plate w/ 2x 15mm Bolts before sliding the hub onto the splines? I had one hell of a time getting that plate to line up with the hub installed. Pulled it back off, got the 2 15mm bolts started, then mounted the slid the hub onto the splines and slid the ABS wire through. Much easier
3 bolts in the back are a nightmare
can someone explain how to get a socket /extension onto the lower bolt holding the hub on, IF the car is not on a lift...near impossible if just jacked up
Good goob
Why not loosen the axle nut with tire on the ground instead by just taking off the center cap on the rim
nice video ......can you please show a video abt how to install back to back bearing arrangment sir
is it better to break the tug on the hub before lifting the car up and before removing the tire wheel too??
I've watched numerous videos on replacing hubs. How come no one uses anti seize on slices
Great job on this video. Very professional! How different is the 2011 version of this Cadillac? Mostly the same?
+David Atkinson Well, we don't have a video for the 2011, so unfortunately we can't tell you if it's the same or not. But the general procedure for changing a bearing/hub is pretty similar to this one, so it will likely be close. Good luck! Let us know how the repair comes out. 1aauto.com 866-403-3393
Ordered new hubs and abs speed harness as I didn't diagnose which one had the problem though I don't see any damage to the harness I'll install the hubs first and it if solves the abs and Tc lights I'll keep the harness as a spare. Do I need a hub puller?
+columbianbambam You may need to use one for this repair. It worked well and made the job easier, that's what we use in the video. Hope this helps you out.
is this the same for an STS?
Nice video but I have a question at that stage of disassembly can the CV shaft come out and be replaced?
Hi Sam, you should be most of the way there at that point. We currently do not have a video on how to remove the axle, there might be a few more thing to loosen or disassembly before it will come out for you. Thanks for watching. 1aauto.com
With the sts you pretty much have to remove the axle, I managed to loosen the top 2 bolts with a wrench but the bottom bolt I can't get a socket in thanks to the cv joint in the way.
+Ryan Patterson Thanks for checking us out!
I have a 2007 Cadillac srx awd are these the same sizes and steps for me to replace my rear hubs?
+keenan d We're always cycling through cars filming hundreds of common repairs for common vehicles every month. We'll add this to our list of repairs to film. Check back again and hopefully we'll have it soon.
great video
How about on a Cadillac STS 2006? Thanks in advance
We currently do not have an auto repair video specific to your vehicle. You might be able to apply some of the basic steps shown in this video to your application. +Herschel Liddell
So itâs possible to just remove the bearing and change out the sensors with out replacing the bearing? Is this accurate?
+Iron Worker 444 When you take a bearing out it is not recommended at all to press that bearing back in, it is for the best to replace it whenever it is removed.
I replaced my rear hub assembly, and it still has a grinding sounds upon acceleration. Any ideas? 07 cadilllac cts.
do the other side
Thanks for your excellent videos, do you ship parts to Ontario Canada or do you have a Canadian outlet ?
+nick king Thanks for checking us out. We do not have any physical stores, however, we do ship to Canada. Please keep in mind, shipping charges are applicable to Canada. 1aauto.com
The rear end is the same way on the 1st gen CTS-V, with the exception of the 6 bolt hub, isn't it ?
Chris Ryan correct
35mm doesn't fit mine, it's 36 mm apparently.
It's different for a STS V. You can't get to the bottom bolt under the axle. Axle to big around to get on the bolt. It's a pain in the butt to work on. Bad design.
Is it possible to get hub off without hub puller?
ШНиŃŃ Đ˛Đ°ĐťĐ° надО ŃПаСаŃŃ...