NEJE Laser 20W vs. 7W - surprising results! | 20W vs. 7W - Überraschende Ergebnisse!
Vložit
- čas přidán 4. 01. 2020
- I am comparing the two NEJE laser modules with 7W and 20W each. The lasers are tested with the same setting. I am totally surprised by the results.
----------
Ich vergleiche hier die beiden NEJE Laser Module mit je 7W und 20W. Die Laser werden mit immer der gleichen Einstellung getestet. Ich bin total überrascht von den Ergebnissen.
Soul-Studio,Ugur Takoz,NEJE,Laser,Engraver,20W,20 Watt,Modul,Mac,MacBook,MacBook Pro,Test,KKmoon,Engraving,Gravur,Personalized gifts,Personalisierte Geschenke,Lasergravur,Laser engraving,Echte Leistung,Real performance,7W,7Watt,7 Watt,Real specification,correct laser power,echte Laserleistung - Zábava
Again - another excellent video. Thank you!!!!
Der Vergleich ist wirklich sehr interessant. Ich hätte nie gedacht, dass eine andere Linse so eine enorme Leistungssteigerung bringen kann.
Sehr gutes Video, weiter so!
Freu mich darüber jedesmal über Neues!
Bitte weiter so!
Danke ;) - Im nächsten Video kommt auch was, was sehr interessant sein dürfte. Liebe Grüße aus Berlin ;)
I always knew there was a reason for why I prefer my 7W over my 20W laser.
Very nice video with great comparisons. Thank you!!
Thank you, too ;)
I'm thinking of buying one of these (7w power with 170/170mm useable space) it's interesting that the lens itself makes such a massive difference! Thanks for your video, brilliant information to have!
Thank you for your comment ;)
Buy the new version!!!! Neje Master 2 or if you want use a rotary device, buy Ortur!
@@SoulStudioBerlin thanks for your advice. I am indeed looking at the neje master 2 7w or the 20w. I think both would do what I need. THANKYOU!
I have two Neje engravers and I have been satisfied with their performance so long. My first was the Neje Master 7 that came with that 7 Watt module. Second one was 2S Plus with N40630 module. Then I have upgraded the mall. I have now N30820 with air assist on my Master 7 with air assist and I have Neje 3 Plus board on my 2S Plus and air assist and emergency stop and two relays. When I got 30 Watt module with my 2S Plus I was so glad while speed increased way more. I could do shorter exposure and would finish few times faster same jobs. Then I have upgraded little one with this module. Later on I have measured power consumption during engraving. I do not have laser output meter so consumption was all I could measure. Both 20/5.5 Watt module and 7/2.5 Watt modules have what looks like same lens plus all of them have backlash spring that keeps them preloaded to be more consistent when focusing. No rubber rings on them. Actually lens on 30/7.5 Watt module looks just a same to. So I have tested consumption and got that actual power consumption of the 20 Watt module is bit over 23 Watt max and like 20.3 average. Same machine with 7 Watt modul was drawing over 10 Watt's doing same job with same settings on same machine. 30 Watt was measured to but with other board and with shorter exposure hence no real comparation. Still it was drawing about 23 watt constantly. So one would say 20 watt and 30 watt are same but they are not.
It is almost impossible to make good comparation even using same machine and same settings. Slight focus and dispersion will make it cut worse. At one moment 7 watt was cutting better then 20 watt module but corrected the focus and things changed in favor of the 20 watt. Even 30 watt out of the perfect focus will do bad job. I guess with laser optical power meter one could measure laser beam strength on different distances and get the maximum value at best focus point and then one could see the real difference. But giving 200 to 300 Euro just for it is bit to excessive for me. Anyhow focus and size of a dot matters a lot. A class lasers have smaller dot and that is advantage. They all also differ in matter how log they keep the beam bundled and what is a shape of the beam. Single diode lasers tend to have right-angle dot and do not keep their focus long distance. Few millimeters only in Z axis. Later on one axis will just go out of focus and it will lose it's power. Dual diode modules have smaller dot and they keep focus bundled longer and those two things matter more than actual doubling the optical power. Beam stays longer in focus and that cuts better. There is a new E80 module that is supposer to carry 4 diodes and I can't wait to see it in the action.
One thing only, stronger is not always better. Sure we all want more power it is human thing but even 10 Watt output lasers can outrun speed of the machine and on some materials engraving will be worse and you will need to lower down the power to the levels of the single diode laser module anyhow. So know your needs and buy accordingly. If budget is no matter knock yourself out.
Thank you for this detailed analysis.
1. Focus is very important. Incorrectly adjusted, even the best laser is useless.
2. Stronger is not always better. It always depends on what you want to do.
Greetings from Berlin
great video Thanks
Thanks!
I know this thread is old but I'm interested in the fix. I'm ordering the 7 watt version and wondered if the power supply might be limiting output power. What is it's rated output? Thanks for the video.
The Laser Power is 2,5W - Module needs 7 W
Thanks for this!
I own a 7w NEJE and a 20w rigged to a '3018' type controller, that I bought through BG and it arrived not working, because of the cheap Chinese board.
Since getting my 20w working, there is a noticible Halo around the focused beam, of around 15mm diameter at +30mm Z distance.
I actually bought a lens with decent coated optics and I'll swap the supplied lenses from the existing 20w and report back if there's any noticible difference.
My 7w is exceptionally good for a deep burn or even cutting, as you've shown here but the 20w _should_ be lots more intense if good optics are used, and the Laser chip itself isn't 'soiled' 🙄
Vielen Dank für dein Kommentar. Ja es würde mich interessieren, ob die bestellte Linse gut funktioniert. Ja und das 20W sollte eigentlich viel tiefer gravieren.
Can you give the link to the lens please?
@@T_aus_B_an_der_Spree If you go onto www.aliexpress.com/i/33003518067.html there's a number of choices, offering multiple lens arrangements with varying quality of coating. Most reasonable quality M9 P.05 Threaded Collimating Lenses will do the job. I've also ordered a Multi-Coated, Multi-Lens Collimating Lens for my 20 W Chinese rig, using a 3018 board as its controller. Limit switches are a pain in the @r$3 and need good quality crimping tools to terminate the necessry cabling to mod it to work with the existing limit switches, but bypassing the proprietory Cheap-Chinese interface, that wont work for love nor money!
schönes, hilfreiches Video! Was ist das für eine Halterung für die beiden Laser an der CNC Führung, an der du die Laser so schnell demontieren kannst? Ich suche tatsächlich nach sowas, um verschiedene Extruder oder Laser am Ender 3 V2 schneller zu wechseln. Würde mir weiterhelfen wenn ich weiß wo man sowas herkriegt :)
Grüße
Hi, die Halterung ist ein Element der Neje Laser Baureihe. Diese habe ich nicht extra gekauft. Das gesamte System ist der Neje Master Laser den Du bei Ebay Oder Amazon kaufen kannst.
Ob es die Halterung auch separat zu kaufen gibt kann ich Dir leider nicht beantworten.
Liebe Grüße aus Berlin
I turned the music way up, loved it lol :)
haha - Yes me too.
Hey man, quick question. I'm thinking of getting the 7w one, and I was thinking if it could engrave my matte black zippo lighter? I don't wanna engrave the metal, just the paint so that I can see the design of the metal underneath. Will the effect be good? Many thanks!
Tobias we have engraved the included metal plate that was also painted black. So the color lasered away. It worked without any problems. The metal under the paint was clearly visible. Nevertheless, you should always do a small test.
@@SoulStudioBerlin Cheers thanks for the help!
I'm a bit confused by the video. Do you think the 20w is worth the extra money? I primarily want to etch someone's name or logo onto pieces of wood.
Hi there,
Yes, it is. Neje Master 2 is really a very good device. This is still the old module. That had problems. The new devices are recommended. But please make sure that you buy the "Master2" series.
Interessanter Vergleich....mit welcher Software arbeitest Du.
Sind die Linsen denn identisch? Könnte mir vorstellen das auf Grund der Laserleistung diese nicht gleich sind. Nutze selber einen 15W Laser.
Ich arbeite mit der Neje Software am Mac.
Die Linsen sind nicht identisch gewesen. Weiterhin sind das die Module die jeweils eine Leistungsaufnahme von 7W oder 20W haben. Die Laserleistung ist geringer.
7W=2,5W Laserleistung
20W=5,5W Laserleistung.
Bei dem 20W Modul hatte ich von Anfang an probleme mit der Linse. Die Treiber und die Software gibt es hier:
wiki.nejetool.com/doku.php?id=nejelaser_master
Liebe Grüße aus Berlin ;)
@@SoulStudioBerlin Danke...
Ebenfalls Grüße aus Berlin 😉
Finally a good comparison! I think the 20w gives a more desiderable result and looks very sharp
It looked sharper because the lens is faulty and was not burning very deep compared to the working lens o the 7W, if that makes sense.
Good test.
Kind regards,
Paul.
Greetings, With a 20W variant, what would be your suggested setting to engrave cedar cigar boxes?
If you have the opportunity to test, I would do a test with low settings. With low settings you can repeat the engraving if it is not strong enough. If the settings are too high, the engraving may look burnt.
I would start with a maximum of 10% laser power and 10 milliseconds burning time.
I actually always test before I start engraving on the end product.
Du bist unglaublich, das konnte ich nicht genau erklären. Aber das 20-W-Objektiv erwähnte, dass es ein Problem hat, also ist dieses allgemeine Problem beim 20-W-Objektiv? Danke
Ja - 20W ist fehlerhaft und ich habe mein Geld von Amazon zurück erstattet bekommen.
Ein Trick zum Ermitteln der Brennweite: eine schiefe Ebene aus einem kleinen Streifen Holz machen und darauf ein Muster aus Linien in verschiedener Höhe brennen. Wenn man das mit voller Leistung macht und über den Rand des Holzstreifens hinaus, dann sieht man auch wie tief der Laser schneidet. Mann kann damit auch festellen, wie viele Durchgänge sinnvoll sind, bevor sich nichts mehr tut.
Danke!!!
Hätte da mal eine Frage, kann es sein, dass ich offensichtlich den Ein- und Ausschaltknopf einfach übersehe? Habe mir den Neje Master 7w gekauft und ich muss ständig das Stromkabel rausziehen, damit er sich ausschaltet? Ich habe den Support angeschrieben und recherchiert, aber nirgends eine Antwort gefunden. (Wahrscheinlich weil es einfach keinen Knopf gibt). Frage deshalb weil es mir einfach unsachgemäß vorkommt, dass Teil einfach vom Netz zu nehmen?!
Im Vorhinein wollte ich Dir noch sagen, dass ich wirklich viele Videos zum Thema Neje-Engraving gesehen habe und Deine bei weitem die besten sind!!!
Mach weiter so - bin gespannt, welches Video als nächstes kommt!
Danke vielmals - ja, hab noch weitere Ideen die ich gerne mit euch teile. Doch zurück zum Ein-Ausschalter. Gibt keinen;)
aber schau mal hier:
www.amazon.de/AGPTEK-Netzteil-Schalter-Streifenlichter-Tischlampe/dp/B07KKCYVJL/ref=sr_1_5?__mk_de_DE=%C3%85M%C3%85%C5%BD%C3%95%C3%91&keywords=12v+2a+netzteil+mit+ein+aus+Schalter&qid=1579114555&sr=8-5
Vielleicht macht der was du willst.
Liebe Grüße aus Berlin
SoulStudioBerlin Danke für Deine Antwort und den Link! Werde ich mir wahrscheinlich wirklich besorgen.
Where is the Best palce to buy? I need one with pwm regulation bcs of usage with 3d printer mod
So I buy from Amazon, Ebay, Aliexpress and Alibaba. There is no shop for this near me.
Hello, can I ask a question.
I'm looking for a laser that performs the cutting of 1.5mm wood veneer the best. The engraving quality is not as important. Is there a specific model for this sort of objective?
thank you
Sarah Wong - Hello Sarah, if you have a PC, you can use the CNC area of the Neje software to cut wood. 1.5 mm shouldn't be a problem. You will need one or two passes. But if you have a Mac, the CNC option is not available.
@@SoulStudioBerlin Hello, thank you for the reply. I do have a PC. In that case, will the 7W do the trick? Or will 20W be better?
I was also wondering for the NEJE software - not being able to use the CNC option on the Mac, does that go with all the models they have?
Klasse Video! Würdest du den Neje empfehlen für Bilder auf Holz?
Hallo Tobi, da ich zur Zeit nur den Neje Laser habe, kann ich sagen dass er mir gut gefällt und man damit einiges machen kann. Ich würde aber nicht das 20W Lasermodul kaufen, es sei denn man will damit etwas ausschneiden. 7W ist total okey.
Ich habe mir einen anderen Laser bestellt und werde die beiden vergleichen, sobald der andere Laser angekommen ist.
@@SoulStudioBerlin danke für deine schnelel Antwort. Ne schneiden eher nicht würd eher Bilder auf holz gravieren und namen in gläser so in die Richtung. Bei Neje steht ja der 3500mw eher für bilder. am besten aber den 7w kaufen und die leistung runterdrehen müsste doch funktionieren seh ich das richtig? auf das vergleichsvideo freu ich mich :)
@@tobiok4063 - das 3,5 Modul hatte ich leider nicht. Aber natürlich kann man die Leistung runter drehen. Aber die angegebene Leistung bei Neje bezieht sich nicht auf den Laser, sondern auf die Leistungsaufnahem des Moduls. Das 7 Watt Modul hatte glaube ich 2,5 Watt Laserleistung und das 20 Watt Modul 5,5 Watt Laserleistung. Ich hatte da ein Video veröffentlicht, dass die Module mit ihren Leistungen kennzeichnet.
czcams.com/video/DwZHD4jvjp8/video.html
can you upgrade a neje master 20 watt laser so it can use lightburn?
One subscriber told me that It will work with a new logic board. And it will work with the Neje Master 2. But I can test it after my Neje Master 2 arrived. I hope next week.
@@SoulStudioBerlin nice. thx
Ich habe auch einen Neje Master 2 mit 7W und würde gerne aufrüsten. Wo sehe ich denn, welches Lasermodul ich einfach so anstecken kann, ohne was an der Verkabelung zu ändern?
Hallo Markus, welches Modul möchtest Du denn kaufen? Vergleiche mal ob es Sinn macht gleich Neje 3 oder 3 Plus oder 3 Max mit dem gewünschten Modul zu kaufen. Wenn es nur ein Paar Euro teurer ist, solltest Du lieber einen komplett neuen Laser inkl. Netzteil kaufen, da Du beim Upgrade zum nächsten Modul auch ein Netzteil kaufen musst, dass die Leistung liefert.
Weiterhin hast Du dann keine Probleme mit dem Umbau ;)
neje.shop/collections/all-products/laser-machine
Schau da mal nach.
Liebe Grüße aus Berlin
@@SoulStudioBerlin Mich würde ein 20W Modul interessieren. Das sollte eigentlich deutlich billiger als ein neues Komplettgerät sein. Der Umbau sah in eurem Video so einfach aus.
@@schnuppig Ja, ist bei mir einfach gewesen.. Du musst nur das passende Netzteil noch dafür holen.
Aber hast Du Dir die Preise mal angeguckt?
Neje hat gerade 10% Rsbatt.
Hier ein Hinweis von Neje - wiki.nejetool.com/doku.php
Important Notice(2019.12.29)
Users who purchased (NEJE 20W module) before October 2019 may experience laser attenuation. If your laser power is attenuated, we will replace it for free. We apologize for the inconvenience!
At present, all laser modules of NEJE will pass rigorous aging tests to ensure no attenuation of power and ensure that each radiator can control the temperature within the standard range for a long time. It can be used continuously without any time restrictions. The cheap lasers bought in the market do not have diode caps. NEJE has key core technology to control the effective life of the laser diode to 10,000-20000 hours, and promises a 2 year warranty! If your laser have problems, You can get it for free from the store you purchased, or contact the official service channel:service.nejetool.com
The 20W lens has been updated. You don’t need to purchase lens to replace it. The new lens can adapt to engraving and cutting at the same time. The cutting light diameter can be controlled within 0.1mm and 5mm length.
please contact us:service@nejetool.com
Ich besitze auch den Neje 20W Laser und habe auch so einen RIng um den Laserpunkt. Kann man vielleicht eine 7W Linse als Ersatzteil irgendwo bekommen? MfG Rico
Rico Hauptmann - Hi Rico. Bei Alibaba gibt es Linsen. Aber einige Abonnenten haben keine guten Erfahrungen damit gemacht. Was machst du mit dem Laser? Gravieren oder Schneiden?
Der Unterschied zwischen dem 20W und dem 7W ist nicht so groß wie gedacht, da das beides nur die Leistungsaufnahme angibt und nicht die Laserleistung.
20W= 5,5 Watt Laserleistung
7W = 2,5 Watt Laserleistung.
Vielleicht lohnt Ja der Kauf eines 7W Moduls.
@@SoulStudioBerlin hauptsächlich möchte ich gravieren. Ich denke da lohnt es sich doch das 7W Lasermodul noch zuzulegen.
Rico Hauptmann - ich habe meine Sachen über Amazon gekauft. Ich konnte deshalb mein 20W Modul zurück geben.
Ich warte wann das bessere Modul auf den Markt kommt und hole mir dann das neuere Modul.
I bought a 20w Neje Master... it started burning but very superficial... after 6 tests it is only making light, doesnt even marks a paper... I dont know how to make it work properly...apreciate any advice
1. Do you use a Mac or PC?
2. It is very important that you set the focus correctly. The distance to the laser should be approx. 4-5 cm. I use black matt paper to focus.
3. Go to the settings in your software and press "Reset Settings"
Try to engrave something again.
@@SoulStudioBerlin I use pc. The focus is at 4,3cm, but it looks like a line and not as a dot... but at least at the beginning it was buring, now its just blue light.
@@SoulStudioBerlin Does the laser makes any light when its burned? itseems to be working perfectly, but dosnot cut or burn even a paper
@@gregorbassojoias If it can't even laser paper, it could be broken. As far as I know there are two lights. One to adjust and then the laser that burns.
@@gregorbassojoias The focus is adjustable. The laser has no fixed focal length. Can't you turn the lens? Can you "Reset" all settings?
Danke Dir für den Test! Sieht bei mir genau so aus mit dem großen Halo um den Fokuspunkt. Das erklärt, warum der 20W "Cutter" nicht cuttet... Es liegt also nicht am Laser, sondern an der Linse. Frage ist nur, was tun? Gibt es Original Neje-Linsen als Ersatzteil?
In diesem Zusammenhang habe ich gerade folgende Info vom 29.12.2019 auf der Neje Supportseite zum 20W Laser gefunden:
"The 20W lens has been updated. You don’t need to purchase lens to replace it. The new lens can adapt to engraving and cutting at the same time. The cutting light diameter can be controlled within 0.1mm and 5mm length."
Die Linse wurde also upgedated, aber ich muss sie nicht erwerben, um sie auszutauschen?? Wie soll ich denn sonst an die neue Linse kommen, ohne sie zu erwerben? :-D
@@Totaltimo hahaha, also die ich von ali hab ist totaler Müll und hat einen noch größeren Halo Effekt
@@T_aus_B_an_der_Spree Mist, die habe ich auch bestellt :-(
was wäre denn nun die lösung? ich hab auch den 20w laser und hab eine riesige Streuung
was wäre denn jetzt die Lösung? ich hab auch 20w und eine sehr große Streuung
Do you have experience with the 3.5W module?
No - Sorry
Hi, i m korean :) I saw your video well.
Can I ask you a question?
-I'm currently using a 7w product and I'm too slow to imprint on the leather.
I'm considering buying 20w products to work faster.
Will 20w products imprint faster?
thanks :)
1. The 20W module is not faster but stronger.
2. There are currently some problems with the old 20W module. Make sure to buy a module that was made in January 2020.
3. Since the module is stronger, you can set a shorter burn time. Before doing so, you should definitely test which laser power you are satisfied with.
4. The 7W module is equal to 2.5 watts of laser power. The 20W module equals 5.5 watts of laser power.
Greetings from Berlin - Germany;)
@@SoulStudioBerlin Thank you very much for your kind and quick reply.:)
I subscribed to you. I'll keep an eye on you.
I hope you are doing well.
thanks :)
손준 you’re welcome
Found at NEJE: wiki.nejetool.com/doku.php
The laser module power is not the higher the better(2019.12.30)
The NEJE laser module is developed according to the actual process
requirements. When you choose a laser, it is not necessary to use more
power. For example, the NEJE 405nm 3500 module has a high power of 405nm
and a very small focus. The short wavelength of 405nm is easier to
Material absorption, all effects and precision are the highest. Its
process features are high-precision engraving, gray-scale engraving and
high-precision drawing images. The disadvantage is the average speed; 7W
modules are good at high speed because of their light weight, small
focal length, small focal point, and high power. Deep engraving,
suitable for engraving logos and patterns; 20W module has a small focal
point and high power, but is relatively heavy. It is good at slow depth
engraving and cutting wood and paper pieces less than 5mm thick; you
need to consider this according to your actual needs Several modules.
Diego vD - Thank you for the information. But the module I use was faulty.
We have some posts about it on my channel.
Hier nochmal in den Haupt-Thread:In diesem Zusammenhang habe ich gerade folgende Info vom 29.12.2019 auf der Neje Supportseite zum 20W Laser gefunden:
"The 20W lens has been updated. You don’t need to purchase lens to replace it. The new lens can adapt to engraving and cutting at the same time. The cutting light diameter can be controlled within 0.1mm and 5mm length."
Die Linse wurde also upgedated, aber ich muss sie nicht erwerben, um sie auszutauschen?? Wie soll ich denn sonst an die neue Linse kommen, ohne sie zu erwerben? Sehr suspekt :-DIch habe dazu am 2.1. und gestern am 6.1. den Neje-Support angemailt, aber leider bislang keine Reaktion erhalten. Wenn was kommt, melde ich mich.
Ich habe den Support schon angeschrieben!
Klasse, danke - mal sehen, wer zuerst was hört! Ich bin gespannt und brenne auf eine neue Linse, seit ich gesehen habe, was das Modul mit einer guten Linse zu leisten vermag!
Ich werde es dann als Kommentar veröffentlichen.
Can it engrave grayscale images, or is it just a single power through the whole run?
Yes it can engrave greyscale images!
@@SoulStudioBerlin
Thank you very much
@@Jasoninee you´re welcome
@@SoulStudioBerlin
Just in case this helps anyone else this actually only has a single power through the whole run. My hope was that it could actually utilize the Gcode that can change the power during the job.
It seems that maybe the NEJE Master v2 will, and the future v3 definitely will.
Is it possible to lower the output? I want to buy 20W option for multi purpose usage, but I wonder if it will be possible to do detailed engraving (with dithering) like DK8 seires can do?
Could you please tell me if you would suggest the 7 w or 20 to cut fabric like cotton? thank you in advance
7W would also cut it, but with 20W you have more options if other materials are also cut. But I would be careful with cotton because the laser does not cut but burns.
@@SoulStudioBerlin thank you so much I have right now a 2.3 w and it does cut cotton but maybe that type of laser neje is different.
The different between the Neje Master 1 and 2 is the speed and a better 20W Modul.
If you wanna cut metal you need a fiber laser.
@@SoulStudioBerlin i am only cutting fabric. I use it to cut the garment before sewing them. but the one I have right now is not that brand but it died after maybe 20 uses. I am looking to replace it with something better 😔
@@josefadavid555 Try Neje Master 2 - I've used it hundreds of times and it still works.
I'm interested in getting the 7w one. Do you know if I could install it directly in to my dyi grbl/arduino laser machine? Or I need to buy the ttl too in order to control the input?
Gonzalo Baldomé - unfortunately I cannot answer this question for you. But Garfield should know. Please search Garfield in the comments and ask him the question again.
Greetings from Berlin
Can someone answer the question please.
@SoulStudioBerlin Quick update! The laser worked perfectly, there's no need to buy the test ttl board from neje. Just connected directly to ramps on the ttl (z-) and voilá!
Your content is great, cheers from Argentina!
Hallo zusammen, ich habe am Wochenende nochmal gelasert, bis die Linse glühte. Und ich habe es tatsächlich geschafft, dünnes (!) Sperrholz von 2mm in nur 6 Durchgängen zu schneiden. 4mm Sperrholz habe ich dann bei 25 Durchläufen geschafft.Offenbar ist es so, dass Neje die Spezifikation der 20W Linse zur Angabe des besten Fokus ("best focal length", bisher 10mm von der Linse) geändert hat. Das habe ich erst später gelesen, aber durch Ausprobieren selbst festgestellt. Was habe ich gemacht:- die Linse KOMPLETT reingedreht- der Fokuspunkt lag somit bei etwa 5,4cm und damit unterhalb der Standebene.- Den Laser etwas erhöht aufgestellt und dann auf 2mm Sperrholz gelasert (Oberfläche des Sperrholz lag somit bei 5,2mm Entfernung zur Linse).- Nach 6 Durchgängen war das Brettchen durch, was ein Quantensprung im Vergleich zu meinen bisherigen Versuchen ist.Die Spezifikation von Neje zur "best focal length" spricht mittlerweile von 40mm. Das habe ich noch nicht probiert, werde ich aber als nächstes mal machen. Das erklärt auch, warum die 10mm nur zu erreichen sind, indem man die Linse fast bis zum Rausfallen rauschraubt: Das scheint für diese Linse im 20W-Modul demnach überhaupt nicht vorgesehen zu sein!Probiert es doch auch mal und sagt mir Bescheid.
Totaltimo - Danke und gut zu wissen. Neje hat sein 20W Laser überarbeitet. Gelten die Angaben für den neuen oder alten Laser?
Wenn ich Dir nur sagen könnte, ob ich den alten oder den neuen habe!? Bestellt und geliefert Mitte Dezember. Ich kann nur vermuten, dass die Angaben für den neuen Laser gelten.
@@Totaltimo - Wie sieht denn dein Focusring aus? Schau mal in das Video von mir bei 3:56.
@@SoulStudioBerlin Der sieht genau so weit gestreut aus wie bei Dir, kein Unterschied!
@@Totaltimo - Dann schein es das alte Lasermodul zu sein, oder Neje hat einfach nur blabla erzählt ;)
Did you check the specs on those LDs? The focal lengths are different, I'm betting. Even so, it looks like you're not dialed in right on the second one.
Believe me, everything is properly focused. These laser modules have no fixed focal length. The module is faulty. Neje has started an exchange program. I have posted it several times now. But I would like to post it here for you again.
wiki.nejetool.com/doku.php
Important Notice(2019.12.29)
Users who purchased (NEJE 20W module) before October 2019 may experience laser attenuation. If your laser power is attenuated, we will replace it for free. We apologize for the inconvenience!
At present, all laser modules of NEJE will pass rigorous aging tests to ensure no attenuation of power and ensure that each radiator can control the temperature within the standard range for a long time. It can be used continuously without any time restrictions. The cheap lasers bought in the market do not have diode caps. NEJE has key core technology to control the effective life of the laser diode to 10,000-20000 hours, and promises a 2 year warranty! If your laser have problems, You can get it for free from the store you purchased, or contact the official service channel:service.nejetool.com
The 20W lens has been updated. You don’t need to purchase lens to replace it. The new lens can adapt to engraving and cutting at the same time. The cutting light diameter can be controlled within 0.1mm and 5mm length.
,Welche Software wurde am Mac verwendet?
Die original Neje Software.
@@SoulStudioBerlin Danke. Wisst ihr ob andere Laser Setups auch mit der Software laufen?
@@benediktklein6269 mein No Name Laser läuft damit nicht. Andere Laser habe ich nicht.
Did you properly focus each one for its distance from the work before burning? You did not show that you did that!
Sotm - hi, always the same question. of course it's focused. Please read the note from Neje that I posted here. The 20W module is in an exchange program because it is faulty.
Does it engrave silicone?
It will burn in silicone - but white silikone is a problem.
I bougt the same 20 watt master 2 neje and have the same dissapointing results. Ordered now the 7 watt lens, see what happens
I use only the 7W module - you will get good results 👍
Ich habe die Linse bestellt, die in den anderen Videos vorgeschlagen wurde, die kam letztens an und ist totale Grütze. Sie lässt sich viel leichter eindrehen als die mitgelieferte und hat einen extrem hellen Ring drum herum.
Und ich habe das Gefühl das der Laser zwischenzeitlich die Leistung etwas runter regelt, ob das mit der Temperatur oder dem billigen Netzteil zusammenhängt kann ich nicht sagen
Aber ein schöner Vergleich, wobei es mit auf ein schönes Gravurbild ankommt und nicht so extrem die Tiefe
T. aus B. an der Spree - Ja das mit der Leistung finde ich wirklich verwirrend. Bei dem Vergleich wollte ich gucken, wie stark der Laser ist.
Das deine bestellte Linse Grütze ist ist auch sehr enttäuschend. Danke für dein Kommentar.
@@SoulStudioBerlin
Ich schicke dir nachher mal ein paar Bilder. Vielleicht siehst du ja woran es liegt. Habe die nicht mal getestet, da mir der streukreis zu groß ist. Schade das man hier keine Bilder einfügen kann.
Am Netzteil liegt es wohl nicht, ich benutze ein recht gutes 10A Netzteil. Sowohl mein 3,5W, als auch mein 20W-Modul haben in der Leistung nach ein paar Betriebsstunden nachgelassen. Auch während des Betriebs lässt die Leistung, nach einer gefühlten viertel Stunde, nach. Das könnte dann ein Teperatur-Effekt sein. Die Grütze hab ich auch bestellt, wurde aber nocht nicht geliefert. Vom 3,5W-Modul bin ich sehr begeistert. Mit dem konnte ich 3mm Sperrholz schon fast durchschneiden. Also habe ich das 20W-Modul nachgerüstet. Mit dem habe ich die gleichen Erfahrungen gemacht wie ihr. Und es schneidet auch kaum tiefer, dafür aber breiter. Laut Angabe des Herstellers soll der 20W-Laser eine Brennweite von 5-50mm haben. Bei meinem sind es 20-70mm. Ich vermute auch, dass das an der Linse liegt. Welche Brennweitenbereich habe eure 20W-Module?
@@wolfgangschindler1408
Das mit der Viertelstunde würde ich jetzt mal indirekt bestätigen, habe aber auch noch nicht viel gelasert. Glaube irgendwie stand mal das man nicht länger als 30min an Stück lasern soll.
Das nachlassen kann auch durch eine verdreckte Linse passieren, der Ruß legt sich ja auch auf der Linse ab, deswegen haben "ordentliche" Laser wohl auch einen kleinen Ventilator der das sofort weg bläst. Das hatte ich gestern auch schon überlegt zu bauen.
Bei Ali gibt es auch Kühlkörper für solche laser, aber ob die was taugen weiß ich nicht. Letztendlich ist es nur ein Alublock der an das Modul geklemmt wird.
Welches Netzteil nutzt du? Habe schon überlegt mal was anderes zu nutzen.
Ich werde am Wochenende mal ein paar Bilder machen und die Online stellen, wie die Streuung bei mir ist. Ich kann zwar filigran Lasern, aber allein das fokussieren finde ich schon anstrengend.
@@T_aus_B_an_der_Spree Mein Netzteil ist natülich auch ein No Name aus China, aber das hat mir schon bei anderen Projekten gute Dienste geleistet.
Moin,das Problem "Streuung" kenne ich auch, hab etwas experimentiert und festgestellt das der laser am meisten Leistung hat,wenn die originale Linse fast gänzlich herausgedreht ist,habe jetzt meinen Brennpunkt 11mm unter der Linsenfassung,6,5mm unter Air assist,,der Unterschied ist enorm...allerdings kann ich bei meinem Eigenbau die Höhe des Lasers einstellen. Kannst du dir ja in meinem Video ansehen,solche Halterung ist schnell gebaut.
PS,laut Bedienungsanleitung soll der Brennpunkt optimal bei 10mm liegen.
Ab
Finde das Video auch nicht. Wäre interessant. Hab ihn auf ein Küchenbrett geschraubt und stell ihn immer irgendwo drauf.
Deswegen habe ich ja nicht den 40er laser gekauft da ist man was das angeht so eingeschränkt
@@T_aus_B_an_der_Spree Die offene Bauweise war für mich auch ein wichtiger Grund. Für eine variable Höhe habe ich mir einen "Labor-Scheren-Tisch" zugelegt.
czcams.com/video/OTBUtYG4YP8/video.html
Das ist mein Eigenbau,funktioniert problemlos,Höhe ist einstellbar,laser schnell gewechselt... OK,könnte schöner aussehen,aber daß er funktioniert ist mir wichtiger
Das der o-ring nicht fest sitzt ist in meinem Fall egal,da das ganze vom Air assist gehalten wird
Lässt sich mit den 20W auch Stempelgummi lasern?
Natürlich! Du musst aber immer ein Test vorher machen und dir die Einstellungen notieren.
Ich würde den Laser nicht zu stark einstellen aber dafür mehrere Durchgänge gravieren.
Viel Erfolg!
@@SoulStudioBerlin echt, hast du selber schon probiert? Dachte wirklich , 20W ist zu wenig.
@@SoulStudioBerlin danke für den Tipp👍🏻👍🏻👍🏻. Das ist für mich Kaufempfehlung genug! Denn Moosgummi kann ich auch mit 5W oder noch weniger lasern. 👍🏻👍🏻👍🏻
@@KoelnGuido Ich habe doch ein Video davon in meiner Mediathek ;)
Uhm.. You sure that You did focus the lens before engraving right? I see one big fat circle there... And you Yourself said it's scattered...
Marcus M. Of course I focused the laser. What you see in the video is a problem with the lens. I don't have this problem alone. Neje has now released a revised version of the laser. I have already contacted Sopport and hope for an exchange.
@@SoulStudioBerlin I have found an info on official site about this problem as well: wiki.nejetool.com/doku.php
See the important notice at bottom.
Wait a second, I am confused, how can 100ms cut deeper than 10ms? Isn't it logic that if it goes slower it will cut deeper?
Different laser power ;)
@@SoulStudioBerlin But I was referring to the 20W module, 100% with 100ms against 20W 100% and 10ms ( 10ms is slower than 100ms, right?) so how come, it cuts deeper when on higher speed ???
And I have one issue here, I just bought Neje master 2 - 20W but I am not able to engrave on the metal plate that was supplied with the machine. Can 20W even engrave or does it just cut? Did I made a mistake buying 20W model?
@@saschasrdoch5997 no 10ms is faster. 100ms is slower.
@@SoulStudioBerlin Really??? I feel stupid now :)))) Thanks for clarification
Ist the burning time per pixel not the Laser speed
Hi, habe nich alle 102 Kommentare durchgelesen, aber von der chronologischen Reihenfolge her hast Du Dein Spiegel engraving vor diesen Test gemacht.
Damit hast Du Dir Deine Linse am 20W Laser zerstört. - Alt. evtl. auch durch Emissionsdämpfe Deiner Versuche.
sharkyone1000 - ich hatte von Anfang an Probleme mit der Linse und habe sofort den Support angeschrieben. Dieser hat mich am Ende damit vertröstet, dass man gerade Urlaub hat. Danach hat sich nichts getan. Wie du vielleicht gelesen hast, haben auch andere Nutzer Probleme mit der Linse, ohne das sie einen Spiegel graviert haben und die gleichen Streuungen. Natürlich haben wir die Linse gereinigt, da uns das mit den Emissionsdämpfen mitgeteilt wurde. Neje selbst hat die Probleme mit der Linse am 20W Modul eingeräumt und ein Austauschprogramm gestartet. Auch da habe ich mich angemeldet aber leider keine Antwort bekommen. Danke für dein Kommentar! Liebe Grüße aus Berlin.
Mit den Einstellungen schneidet der Laser 4mm Sperrholz mit 70mm/min in 18 Durchgängen,zum Schneiden ist er etwas Schwachbrüstig,aber es geht.
Zum Thema Wärme... Bei meinem Board ist kein Anschluss dafür,ist auch nicht notwendig,bei 100% Leistung wird er nichtmal handwarm.
Ich habe schon mit 3mm Schwierigkeiten. Und nach 5 Durchgängen sind kleinere Details gänzlich verkokelt. Welche Software verwendest du?
Wenn er von mm/min redet, dürfte es mit einer CNC Software sein. Er arbeitet ja auch mit CNC, da liegt das nahe.
Da muss ich mich aber erstmal rein lesen. LASERgbrl könnte das vielleicht.
Ja,laser gbrl und estlcam für den g-code
Wenn man mit estlcam arbeitet ist die Spindeldrehzahl 255 maximal (entspricht TTL Signal) bei Kurvenfahrten nimmt das Programm automatisch Drehzahl weg,in dem Moment auch Laserpower. Sicher verkohlt es etwas,das liegt aber daran das man eben so oft drüber gehen muss,ein Leistungsstärkerer Laser zieht da mit einem Schnitt durch,da sind brandmarken nicht so problematisch
They make 2 different types of lenses, one for near focus and one for far, looking at the ones you have, that is exactly what is going on. If you look on Aliexpress they are very cheap.
Yes, but they also made faulty modules / lenses.
Read this from Neje:
Important Notice(2019.12.29)
Users who purchased (NEJE 20W module) before October 2019 may experience laser attenuation. If your laser power is attenuated, we will replace it for free. We apologize for the inconvenience!
At present, all laser modules of NEJE will pass rigorous aging tests to ensure no attenuation of power and ensure that each radiator can control the temperature within the standard range for a long time. It can be used continuously without any time restrictions. The cheap lasers bought in the market do not have diode caps. NEJE has key core technology to control the effective life of the laser diode to 10,000-20000 hours, and promises a 2 year warranty! If your laser have problems, You can get it for free from the store you purchased, or contact the official service channel:service.nejetool.com
The 20W lens has been updated. You don’t need to purchase lens to replace it. The new lens can adapt to engraving and cutting at the same time. The cutting light diameter can be controlled within 0.1mm and 5mm length.
please contact us:service@nejetool.com
SoulStudioBerlin Thanks for the reply, that is interesting to know and take it on board. The reasoning for my comment was the 2 different colours of the lens holder is similar to the ones with the 2 different focal lengths.
@@SoulStudioBerlinWhere would be a reliable site / dealer to purchase a decent 7W laser module?
Will the laser put a legible mark on top of a coca cola plastic bottle cap?
Hi, since it is made of plastic, it will certainly burn something in. Unless it's transparent. I can't answer exactly what you mean by readable. If you write too small no one can read it. Too big and nothing fits on the closure. Then of course there are the settings. Too strong and it burns through the closure. Too weak and the writing is not burned deep enough. But all in all: yes plastic can be marked.
Greetings from Berlin
@@SoulStudioBerlin Would you try it? Say, for example, place an X in the middle of the cap? 1mm line width? Would really be curious to see it.
@@MisterFizz HI Archie, I have now tried it quickly. During my first attempts, the laser cut the cap like butter. After a couple of tries, 25% laser power and 25ms burn time (fast mode) I got visible results. I think with a little more time and better settings you can get good results. But I can't imagine if that's what you want. I think you mean colored marking like fiber lasers can. This laser cannot do that.
Here is the video:
vimeo.com/405486138
Pass: youtube
Greetings from Berlin
@@SoulStudioBerlin Fiber lasers leave acceptable marks on some polymers. MOPA fiber lasers are a bit better. But UV 355nm offers the most versatility. The "laser ink" by HEVES®TEAM is super-expensive and a VERY slow process. I love it for a one-off dirt cheap solution for individual user with single project a few times per year. But no practical commercial application is suitable to make use of this tech. Even screen printing methods are far more practical.
@@MisterFizz Yes you are right! Screen printing is really cheaper than "MOPA fiber lasers". On my channel you could see what you can do with this laser. Metal doesn't work for me. But my wife has a 30W fiber laser for that. She designs jewelry and makes rings.
Her channel:
czcams.com/users/coinringberlin
If I can help you in any way, just let me know.
Greetings from Berlin
Hallo, obviously you get always the same question about the distance and focus ;)
Range and distance of focus are very different between the 7W and the 20W.
Almost nobody is going to (except me, I found it) take the trouble to go through all the comments to find the one about the Reply from NEJE.
Auso was Du machen solltest, IMHO, ist in einen neuen Comment, genau der Reply einfügen, und dieser "Pinned" at the top so it is sichtbar for everybody, von Anfangs an.
Daneben, in der Beschreibung sie sagen dass der 7W ist lieber for deep engraving, während der 20W ist nicht so schnell wie der 7W aber kann doppel so dick schneiden. That is an important difference and one should choose between the 7W and the 20W according to the planned usage of the machine and surfaces.
Do you agree?
Sonst, meine Meinung nach, was auch gut zu wissen wäre wie lang (Zeit) braucht es für jeder Maschine den gleichen Arbeit fertig zu machen.
Thanks ! Tschuss
PS: Ich gehe davon aus dass everbody is at least fluent in both German und Deutsch ;) Sinon ben tant pis pour vous !
THX
Mein 20W Laserkopf sieht etwas anders aus - so wie der vom 7W.
Er schneidet Holz bei 45ms/100% mit 10mm(!) Dicke.
imgur.com/VRqKUs2
20W gekauft in China, 112 €.
Eine zusätzlich gekaufte Linse (6€) lässt sich auf beiden Lasern nicht fokussieren.
Danke für das Bild und die Information. Man sollte sich also zur Zeit keine Ersatzlinse kaufen. T aus B hat ja auch schlechte Erfahrungen damit gemacht.
Die schlechten Erfahrungen mit der 6€ Linse kann ich bestätigen. Egal welche Höhe - keine Fokussierung möglich.
Holz mit 10mm (siehe oben) schneidet der 20W Laser durch.
Nochmals getestet imgur.com/udh48HW
und konntest du schon was herausfinden?
Keine Antwort - nichts. Aber ich lasse nicht locker ;)
Hier der Trick zum Laser einstellen von Ultimartum
czcams.com/video/07kkYnuCwko/video.html
Jede Hilfe ist Willkommen ;) - aber am besten ohne Doktorarbeit ;)) -
Bigger is better.
Neje laser modules don't hold up. and they don't like to warranty them either. good luck..
I got my money back for the defective laser. Amazon transferred the money back to me. The support from Neje stopped me. But as I said, Amazon took care of that.
@@SoulStudioBerlin I made the mistake of buying it from NEJE. Learned my lesson.
@@Cantstandbs The Neje Support did not get back to me. The seller tried to pass the time and wrote that they were on vacation. Thank goodness Amazon took care of everything.
But the new lasers are good. Neje has probably learned from the problems.
@@SoulStudioBerlin I don't know how NEJE gets good reviews. I have a bunch of people saying the same, NEJE just does not want to deal with anyone that's not an influencer.
WTF !?, 20W>7W!, why?
That was a faulty module. Please read the comments because it is mentioned.
Nochmal zu der Grütze Linse
Gerade das Video gefunden, so ist meine gekaufte von Ali auch
czcams.com/video/4hxF3QEMRKs/video.html
so ein Sch-ei-.. Was hast du dafur bezahlt?
@@SoulStudioBerlin 6 oder 7 € gibt ja nur ein oder zwei Anbieter dafür
Not focus
Not "not focus"! It wasn't possible to focus it properly. It was a knowing problem of this module.
But it was solved in the new modules of Neje Meister 2;)
Please talk and stop the infernal noise
Thank you for your comment.