LED LIGHT BAR INSTALL AN DRIVING LIGHTS
Vložit
- čas přidán 4. 08. 2017
- Please like, share and subscribe !!!
If you would like to promote your products or have them installed in one of our video's send a message to our facebook page @
/ servicemyride16
Today I installed the Big Red L.E.D. driving lights and the Narva L.E.D. light bar, I also used a wiring harness from Narva that supplied the relay, cabin switches an fuses, this will take about 2.5 hours to install depending on skill level.
WIRING HARNESS LINK:
www.narva.com.au/products/brow...
BIG RED DRIVING LIGHTS LINK:
www.bigredled.com.au/LED_drivi...
LIGHT BAR LINK:
www.narva.com.au/products/brow...
NUDGE NAR BRACKETS:
from ebay, check for correct size
www.ebay.com.au/itm/232189391479
Want to send me stuff!!!
Attention: Service My Ride
64 Jersey Rd
South wentworthville
N.S.W 2145
Australia
Thanks 👍
Disclaimer
The videos created by Service My Ride are for veiwing purposes only, No claims to be made against the company and or any person related to the company, any damage caused to veiwers property is not in any way the responsibility of the company Service My Ride. If the veiwer is not comfortable with any of the information in the videos they can contact Service My Ride or seek advice at their nearest qualified motor dealer. - Auta a dopravní prostředky
can I ask how you get away with the light bar being so low
awesome video love to watch more videos
Great Vid!
Cheers mate, thanks for the sub 👍
Which alloy bar have you installed?
Big fan m8! Feedback on the lights power usage off cranking battery? Any issues? Cheers
glad i found your vids😉
Dan B No worries mate, glad you found them handy
Thanks for the video mate.
I have a question if you have the time.
I have a set of spotties that have been on the vehicle 2 years without problems. Wired the same way you've done it here.
I recently bought a LED lightbar and wired it independently (even using the other side high beam wire as a trigger). Both the lightbar and the spotties work when they're on, but when I turn off the lightbar the spotties lose power and turn off too. Any idea what might be happening here?
Cheers mate.
Not excatly sure, 1st check the earth wire to the LED bar is that it a clean earth! 2nd try using the same trigger wire for for the LED bar that the spotties are using, easier setup and cleaner, still have independent relays and switches just use the same trigger, heard of this happening when the amps drop from 1 head light to another turning off a aux light can do this, that's where I would start.
Awesome video, really informative. I would've liked more of an explanation about the relays and how they work so I can recycle that info for other projects but the rest was awesome. Time to get me some lights. Would you recommend HID driving lights and an LED light bar or just LEDs all round?
Thanks mate, there is heaps of info online about using relays in different ways, this was just for the light bar so not to much to show, in lights I haven't dealt with HID before but those who have love them, I'm happy with the LED for now.
Instablaster...
Hi Mate, you mentioned in this video you are going to installa switch box for the rocker switches. Did you find one? Do you have a video or reference of what you got and where you did put it in the car? Cheers
Hi Walter, I've purchased quite a few different types of switch boxes but not happy with any of them, jump on to the face book page as I will be installing them soon in a neat spot, no video but a post with pic will be going up soon, thanks mate!
Hi mate, check out the link below of my switch set up
m.facebook.com/story.php?story_fbid=2914776635213715&id=1320083451349716
Hey mate, are the spotties and light bar all run through the one switch because I noticed you could turn them on separately?
Hey mate, They are running on 2 separate switches and relays so I can run 1 or the other or both.
Hey mate how are you? I was just wondering what headlight bulbs do you run in your Triton? I’ve been playing around with different halogen bulbs but was going to try some LED bulbs👍
Cookie can fly how was the response he gave ya mate
You'll need blinker and headlight fluid.
Hey man how are you! Bro what diameter clamps did you use for the led light bar? That pipe is slightly smaller than the rest isn’t it? I’ve got some 76mm clamps at home but they were too big. Thanks 👍
Hi mate, busy as always setting up the garage and new studio, the clamps in using are 66mm-71mm, they are slightly oversize but I've used strap rubber (from Clark rubber) to fill the difference, hope this helps 👍
Service My Ride awesome as man! Thanks for your videos they are so good! Yeah perfect that’ll be good,
Cheers
Send us a message on Facebook an I can send you a pic!
facebook.com/Servicemyride16/
Hey mate have a few questions.
1.You wouldn’t have a tutorial on how to change the fog lights in the triton I’m not sure whether I have to pop out the fog light surrounds or get up behind the bumper
2. What diameter are the bar clamps where the light bar is installed
Cheers
hey mate, no tutorial but the best way is to remove the inner wheel arch to access the clips on the fog light, will pop straight out, the bar clamps are 66mm-71mm with rubber infill to clamp tight on the bar cheers
You are a legend. Thank you for your videos
awesome vid... but if my rig is negatively switched??? I have a Challenger PB 2011 and if I connect this way... will not work... can you help me??? cheers mate
labate71 if you are using a wiring harness that is plug an play you will need to swap the wire in the plug, in the video I connected directly to the high beam
Service My Ride if they were H4 it is easy.... but they are HB3... i believe the only solution is a smart harness...
Could you please share a link to the wire harness you purchased
Those light sit pretty high. Is that "technically" legal?
Does doing this reset the vehicles radio?
I lost the presets on the radio, didnt need the code if that's what your asking.
@@ServiceMyRide yea cheers mate for the quick reply
hi a can you tell me if the grill just pop out try to do mind but would not pop out is there a trick to if or what thankyou ?
Hi mate, remove the 4 clips on top of the grill then pull outwards, they are tight to remove. pull it evenly so it doesn't break.
@@ServiceMyRide yea did that took then all out tight a s all hell so they are not one peace grill and bumper so the bottom just pulls out ?
yep 2 part grill and bumper, just need to pull apart
@@ServiceMyRide cool tar for your info and help will try to do it tar
Hi what brand of nudge bar is that?
Factory fitted GLX-R nudge bar
Service My Ride cheers, great video.
my wiring harness is different
The driving lights on top of the bar are illegal.
Hahah took me 20 mins