C5 Corvette - C6 Z06 Shock Upgrade!
Vložit
- čas přidán 11. 09. 2024
- I have upped the power on this 03 C5 Corvette and now it is time to upgrade the suspension. Follow along as I upgrade and swap in the 2013 C6 Z06 shocks to increase the performance of my C5.
Front C6 Z06 shock GM # 10313647, Rear GM # 25819268
big zip ties are better than a coat hanger - easier to remove
Agreed - good tip!
Thanks. You helped me. Tie rod stud bolt is so easy there it’s just easier that way IMO. One thud with a rubber mallet drops it and it will swing out of the way.
Not sure I understand?
He is just saying it’s easier if you remove the tie rod link. The tie rod links are very easy to get off
Thanks for the install video, as I'm preparing to swap out my original shocks on my Y2k Vette with 90K miles on them. Could you share any updates at this time, ie: ride comfort or lack thereof, handling, etc? I'm considering turning my stock ride height bolts down a bit also, in attempt to diminish the gap between fender and tire. Thanks again for sharing your experiences!
the bottom bolt and nut are both 24MM for anyone that wants to know :)
Thanks 4 that!
Thanks deffinanty going to do this come spring. My shocks are getting long in the tooth
They really firm it up - great for nice roads and spirited driving, bad for a couple hour road trip on crappy roads. A trade off - just like everything!
Nice upgrade!
Another great video. I am looking to upgrade my stock 2004 C5 with new shocks and use at the Brainerd track. With that said, I have gone to Summit Racing and some other sites and they claim Front C6 Z06 shock GM # 10313647, Rear GM # 25819268 don't fit my Base Corvette. However, the forums seem to say yes. You look to have a Base 03 so just wanted to verify 100% that these will fit my Base 04 also as would make sense?
Yes sir, I used the shocks with the part numbers in the video and they work very well!
Thanks for the video. At 4:50 you mention how if you rotate the flange you have a gap. Did you notice the top flanges are not the same as the C5 upper flange? The C6 flanges have an angle. I haven't been able to find out any information on this and they have been installed on alot of cars. I don't think there is any problems in reality but I swapped the flanges. Any thoughts?
Unfortunately, I did not take them off and compare so I cannot say if they are exactly the same or not. I suspect they are as the new ones bolted in just fine - I just spun the top part to the position that matched up best to the chassis.
Well? How does it work??
I finished the front as well now, see video, it helped the wheel hop but did not cure it. Much more firm ride now, like I sports car should be..
very nice will be doing this soon, did you ever try a different trans mount? they seem to help a bit.
Not yet, I think I'm going to go with new motor mounts over the next winter as That would seem to have the biggest control over engine movement. I'll reevaluate after that.
beezy builds just installed a set of engine mounts on his car the helped quit a bit with movement. he also had a discount code for trans mount not sure if its still active, it was around 180$ after discount.
Just in case you happen to get notifications on older videos. I got some c6z shocks...but it is missing the upper plates or flange with the two smaller bolts. Do you think the c5z flanges can be used? Hope so..or i wasted some money🙂
Front or rear shocks?
@@Toys4Life rear. The fronts are not designed that way.
@@Toys4Life thanks for reply by the way!
@@Toys4Life might have to do one and just see if interchangeable.
I just looked at these side-by-side comparison at 3:33 and from what I recall I think I would probably go ahead and do what you're saying. I think it'll be fine. Obviously I can't guarantee it but I would go for it.
I would like to do the same thing, do you know if those same shocks will work on a 2001 ZO6?
Yes, I believe they will.
@@Toys4Life Thanks for the help
one question: the STOCK C5 shocks are electronic no?
Most are not, some do have magnetic ride control which are electric.
@@Toys4Life I had to buy a Tech 2 and do the "R45" delete. C6 ZO6 shocks are a MUST on C5 Vettes! Thanks m8!
@@Toys4Life mine has the magnetic ride it’s a 2004 c5 base , will these shocks fit on mine ,
Part numbers?
Front C6 Z06 shock GM # 10313647, Rear GM # 25819268
Thanks!
What are the part numbers you used?
Just added to the description in each Vid. Thanks!
Do you have the part numbers by chance ?
Front C6 Z06 shock GM # 10313647, Rear GM # 25819268
What does GM say the torque should be?
162 ft lbs I believe. When taking mind off it did not seem nearly that tight on either side and there are no signs of movement/wear between the shock and lower A arm. I will keep an eye on to make sure it is not moving.
Toys4Life C5 Thank you. I gather the ride was much improved. Sooo, what kind of money were they and where did you buy them? Thanks, Bob
We have an 02 triple black convertible with 39700 miles on it and I plan on doing a lot of maintenance work to it.
250 for four of them. Summit racing.
Toys4Life C5 Thank you, sir. Happy Motoring!!!
what about f55 shocks
F55... Too spendy for my blood....
Now u will have a messages pop up on dash show that
Show what?
These are direct fit for Base model C5s. If you have the Z45 suspension yes, you just have to run simulators or 10w x 10ohm resistors.