I did a thread and bearing size repair on a car rear left lower arm spindle lathe machine
Vložit
- čas přidán 12. 11. 2022
- I did a thread and bearing size repair on a car rear left lower arm spindle lathe machine
#thread #bearing #repair #car #left #lower #spindle
So there, champion the turner.
I impressed on how he got a hold on the odd shaped part .. Nice job , I always impressed on how these guys make things happen.
Thanks
Yes and the run out on the tail stock and it finishes well.
Nice one
моё мнение нужно было нарезать на валу меньшую резьбу и сделать под неё гайку , ибо от сварки структура метала меняется и кто знает как он поведёт себя , лопнет в ненужный момент и будет беда
Там ещё и криво всё
Тихий ужас! Для какого нибудь мотоблока огородного еще хусним, но для автомобиля как то стремно.
Welding is a strong joint
I've never been so afraid in my life.
It's nice to see people who know what they're doing. Liked and subscribed.
Thanks
No one here knows what their doing
@@smashface3080 what don't you understand? Everything is very clear. The man restored the carving, and he succeeded.
Why these repairs mostly fail in western countries?
Here the secrets of success:
First you must wearing safety pajama but bended welding rods are the real secret for doing these repairs right.
🤣🤣🤣🤣🤣
This is a pretty old, and worn out lathe, at least the tailstock is. He has the spindle sticking out WAY too far. But I'm impressed with his mechanical ability, to chuck up such an irregularly shaped part. It probably would've been best to turn all the old threads off first, and turn it around .100" undersize. Then add the weld. I wonder how this turned out.....
Hi I was thinking exactly the same as you wrote, the health and safety in the UK would have had a s*** attack at that ! All the best from Henry in the UK 🇬🇧
ps witch country are you from ?
О чудо чудное этот резец ! Всем резцам пример . После сварки всё повело , посадка под сальник гуляет . Проще было напильником сточить и следующую резьбу нарезать .
Wow 😮amazing, you are the best!
People like you can’t do this in USA 🇺🇸
Thanks
*Anywhere else in the world they'd scrap it and buy a new one. Also mainly for safety.*
I keep wondering where the ground is connected for the welding. Is it arcing through bearings
Yes it is😱
@@MsRustynuts
Maybe the tray it was on??? But not really?? Sad workmanship.
Прихожу к токарю, говорю пройтись сверлом нужно в лобовине (крепление генератора немного разбило, эллипсом стало), даже втулка уже есть, на 16 сверло нужно и ровно пройти. Говорит, тебе лобовину контрактную дешевле будет купить, под заказ из другого города, чем моя работа стоит. И так за что не возьмись, проще и быстрее новое купить, чем к мастеркам обращаться.
И когда я смотрю подобные видео, всегда удивляюсь, в каких условиях и за какую работу берутся эти индусы/пакистанцы.
Это сильно взлетелый токарь....
*В который раз спрашиваю - зачем гнуть эллектрод перед сваркой ?*
у меня сварной на работа так тоже гнет говорит ему так удобнее не нужно руку поднимать что бы угол был так мол руки не устают
@@user-of6ou3kx8b А как-же обмазка на эллектродах . она же лопается .
@@ro-manovich На рутиловых не лопается.
В этом видимо и заключается секрет...иначе ничего не выйдет
😲😲😲😲😲😲😲
Thanks for sharing your knowledge, a great job. A WHOLE CRAFTSMANSHIP.👏👏👏👏
Good job
Thanks
Great 👍
When it comes to cost benefit, I don't know if it's worth it, but I really like the willingness, the intelligence in creating resources to perform the service, and not least talking about courage, sometimes I get a little apprehensive about the risks of this type of service. if the parts are reliable, according to technical standards.
In Pakistan parts are not readily available and if they are then they are very expensive.
Don't let you First World Privilege get in the way you think. Pretty sure they don't have Parts stores every other block or wrecking yards available. Parts are rare and very expensive.
Sakthi Engineering channai super super super 👍
this guy is incredible he can fix anything. well done i hope you are going to continue to make videos of this machinist. how many years is he being doing this ? can you tell me is name ?👍👍
Thanks
Garbage
This is not a machinist, a machinist would not do such a stupid thing, this man is an ironworker. A career that turns scrap iron into eternal scrap iron.
خراطة الاشكال الغير منتظمة تحتاج الي تثبيت جيد وكذلك سرعة بطيئة جدا، احسنت عملا ياصديقي💪باكستان
Nice
👍👏👏👏
I respect everyone who were involved in this Seriously the best piece that i ve ever seen on CZcams 💌 Hate off to well all 💟 love your videos
Amazing I like it
Yea nice replying to your own video
@@smashface3080 Thank you Sir
Does anybody make a CNC auto-centering four jaw Chuck? It shouldn’t be hard to do.
Nice work brother
Nice video
Super hero of tight budgeted. 👌👌👌
Torneiro muito criativo vejo fazer trabalho super difícil de aliar a peça no torno dez
👍👍👍👍
I think turning it smooth, cutting new threads and using/machining a new nut would be a more proper fix. But hey, thats just me.
좋은 생각 입니다! 어떤 것이든 모두 고치는 분 !
Here Kurtis Mayfield Memphis Belle a Lulu challenge what do think sweetheart their bloody good
Красавчик👍
Essi torneiro mecânico e muito inteligente
Таким делом занимался 10 лет и утиля на авто
Только в качестве демонстрации возможностей токарного станка и находчивости токаря... не более.
Касается ремонта этого узла.
👏👏👏👌👍
👍
Золотые руки
excellent
По индийским законам , если ты умер у токарного станка из-за отлетевшего в лоб рычага - ты попадаешь в следующей жизни в токарку уже с бОльшим разрядом токаря ;)).
Хоть бы противовес приварил. Бог вращения ;))
Genius
Should never weld over a lathe bed, the spatter will to stick to the bed ways plus he has earthed the lathe and the welding will arc through and destroy the bearings, and the wheel bearing will last no time on that rough shaft🙄🙄
Amazing
Thanks
Masha Allah 🌹🌹🌹🌹🌱🍁🍁🍁☘🍃🍃🍂🌺🌺🥀🥀🌺🌺
Thanks
Горе мастера сломается в самый неподходящий момент
Maşâllah
🤦♂️😮
I didn't know this part of the world was so educated in machining. I'm impressed and my world view has changed. The west gives the impression that other countries don't have the capabilities of machining.
Too many things wrong with this to list them,all the Engineers watching this will know exactly what I mean,we dont do this in the west because we're not cowboys and we do it right!
Очень опасно... Может рычагом убить, но токарь молодец
Nice