Whirlpool Washer Repair - How to Replace the Drive Hub Kit
Vložit
- čas přidán 8. 07. 2024
- Need help replacing the Drive Hub Kit (Part # W10528947) in your Whirlpool Washer? Watch this how-to video with simple, step-by-step instructions for a successful DIY repair.
Don’t already have this part? You can pick up an authentic OEM part sourced directly from the original manufacturer here:
www.fix.com/parts/washer/mayt...
Fix Part Number: FIX6012095
OEM Part Number: W10528947
Why you might need to replace the Safety Pad:
1. Will Not Agitate
2. Pumps But Won't Spin
The information in this video is specific to Maytag, Whirlpool, Kenmore, Amana, Crosley, Inglis, and Admiral Washers. To find a Drive Hub Kit specific to your model Washer, or to use our helpful model number locator, visit www.fix.com
Not what you’re looking for? For more Washer repair help click here: www.fix.com/parts/appliance/w...
For more helpful Washer Repair videos, you can browse through the Washer Repair playlist on our CZcams channel: • Maytag Washer Repair -...
Fix.com is committed to providing you with high-quality parts, quickly and easily. Find out more about our fast shipping and interactive customer service on our website.
www.fix.com/
Stay safe during your repair! Be sure to check www.fix.com/safety/ for proper safety procedures before you begin. Use of this video is at your own risk, without liability to Fix.com.
Connect With Us!
/ fixdotcom
/ fixdotcom
plus.google.com/+fixdotcom
/ fix.com
If you found this video helpful, give us a thumbs-up, and subscribe to this channel for more useful repair videos! Don’t forget to leave us a question or comment below, and our customer service representatives will be happy to help! - Jak na to + styl
1:50 mark.
Just lift up on the agitator and pull it off the shaft... 😅😂🤣
Life is so easy on planet Studio.
I like the revised metal hub kit. Recalibration
This is anything but an easy job,had to break off that plate
How hard was it to remove the agitator
Me too.
Mine is still hanging on like a hair in a biscuit
Good video. Helped. Calibration was necessary after I fixed mine, but I found out how on another's video. Thanks.
Always looks easy😂
I have encountered several wash plates recently that are fused to the shaft, nearly impossible to remove.
Thank you so much I really appreciate the video
Get a few of these Hub Kits......You'll be doing it every year or so
The gear on the top of mine is too big to take the part off. It’s not narrow like the one in the video. No idea how to take the old hub off or get new one over it. Does the gear portion come off? Mvwx655dw0.
Anyone know where to find more screws?
I am replacing this on my washer. What gets me is under that plastic drive hub there is a small chamfered rubber or neoprene washer for each screw that secures it to the basket. Idk where to get those from. I've even looked at the manufacturer's parts schematics and they are conveniently left out. Anyone know what I'm talking about or where to find them?
Is there a trick of other method to get the first screw loose. Tried holding it but can’t get the bolt to loosen.
No. These are not easy and you have to destroy that plate to get it off
This video is a lie
I used my impact driver to remove the screw. Still haven't figured out how to get the agitator plate off.
3rd time around , tub is loose, suspension is worn out! Banging on sidewall, foam worn out, replaced with rubber. Mtce manual inside front wall.
So I have a different issue i have checked three times and confirmed the p/n for this hubkit for my machine but the head of the splines on the transmission are larger than the opening on the drive hub I cant get the old one off and or the new one on. Its not a perfect round shaft with splines like the one in all the tutorials that I have found mine has more like jaggeg shark fin splines three of them rather than like the twenty smooth strait splines?? Please help even called Appliance repair guy and he's lost :(
The plastic "fork shaped holder" is stuck. Tried prying it out and it ended up breaking. The forks won't move. Any ideas to help get these out?
I have the same problem
Very Good!... #24 ✝ {12-4-2022}
It's not even close to being this easy!!!!
My fork won't go in and now it's stuck from hammer
Replacing ours now for the second time. Looking for a metal replacement instead of plastic. With plastic on metal these teeth on hub will keep stripping. 🤔
That’s because your gearcase is bad
Plastic is for saving the drive and motor. If it were metal, you would have more problems, and much worse. Check for loose change, etc under impeller. This holds up the drive and causes the stripping of the hub.
Yeah if only they spend $30 more to make the part out of metal to begin with. Imagine how much happier their customers would be.
@@scottchristie2819 I'm sure they could have thought of a stronger non corrosive material than just plastic
@@netmaster88 You just do not get it dude. Metal would ruin machine.
If you do a lot of laundry, do yourself a big favor and have a few of these pieces on hand. Because these tend to fail when you’re gonna need it most.
So ... you mentioned about putting a cloth over the holes to prevent anything from dropping in there because it's really hard to get it out if that happens. Well ... I didn't cover the holes, and the removable screwdriver tip came off and went right down in there. Is it absolutely necessary that I retrieve it? I can't imagine what that entails! Your video was excellent. I can't believe this happened. :(
Bridget Kulick once you take the little u clip out you can lift the tub out and just grab it
You do not want anything in the drive hub area. Loose Change will ruin it, so a screwdriver tip will do much more damage. Get it out, and look for other stuff in there, too. Hope this helps.
@@scottchristie2819 How do you access that area? By taking the inner tub/basket out?
@@scottchristie2819 Or does it fall down into the drain pump?
What does your washer do when you need to replace this part?
Don’t spins
It will not spin but you’ll also hear a weird sound when it doesn’t spin.. motor will still spin the clutch and splutch assembly but won’t spin... kind of a dumb design imo why have a metal trans slash gear case shaft and plastic hub? It’s a money thing generates revenue and you’d be surprise at the amount of techs that misdiagnose this repair
I can't get my agitator off. The whole world is underneath it hanging on. Tannerite time
Gotta call BS on this. Agitator was already loose. Need video on how to get agitator/cover off.
Seriously? Not going to clean the bottom of that tub up even a little before installing that new part?