DumboRc X4 and X6 control setup plus end point adjusting for channel 3-4
Vložit
- čas přidán 3. 12. 2020
- Hi welcome back,in this video I take you through the setup and function of the X4 and X6 control with receivers.
The receivers setup in the same way except for one feature the Gyro.
The X4 4channel control is paired with the X6f receiver.
While the X6 6channel control is paired with the X6FG receiver the G signifies Gyro function and can't be used with the X4 control.
I take you through a basic setup and a problem solve solution if what you see happens. Then I take a look at how to set end points on channels 3 and 4 on both control.. you may find this bit interesting if you run rear steering or have E-brake function on your car.
Dont forget to like,,comment,share and subscribe to my channel It all helps keep the show alive.
Also why not check out RCunexttuesday subscribe to those guys.
One thing to add, there are apparently 3 different versions of the software, each with different ways to get into settings or to change the mode from mixed/tank mode to standard controls.
Yours are the most common:
settings: from off, hold left and full throttle, turn on, release, then push #3 to enter settings... light will start flashing, and #3 again to save
mixed/tank mode: from off, hold right and full reverse, turn on, release both, then pull full throttle to change modes, light will change from blue to red to indicate it is in tank mode.
older ones:
settings: from off, hold steering full right, no throttle. turn on, release steering, push #3 to enter settings... light will start flashing, and #3 again to save
mixed/tank mode: from off, hold throttle at full reverse, no steering. turn on, hold full reverse until light starts flashing, then pull to max forward to switch modes. red is tank, blue is standard
my X6 is slightly different, and doesn't match any instructions i've seen anywhere...
settings: from off, hold left and full throttle, turn on, *keep held until light starts to flash*, then release, press 3 to enter settings and 3 again to save when done
mixed/tank mode: from off, hold right and full reverse, turn on, *keep held until light flashes red/blue*, then release, press 3 to enable changing the mode, then full throttle to switch modes, then 3 to save.
A massive thank you for this! I couldn't figure out what was going on with my car and the instructions are useless. Now she's a flyer!
Ah the dreaded instruction thingamabob 🤣 it made me cry for about two days but I simmered down eventually ha!
Glad it's helped just mind those curbs 👍
Man I really appreciate people like you. Thanks
What a name RCTroutt epic, thanks I appreciate your comments and support glad it helped.
FINALLY I find a video that shows how to set the channel 3 and 4 end points! Much appreciated!
Your welcome dude, it's great once you know how 👍
Great explanation of Dumbo remote, thanks. It was very helpful
I hope I wasnt too all over the place explaining these things are a nightmare to work BUT great once you get there. Cheers for the comment 👍
Cheers for video regarding end point setting on these radios.
Hopefully I done the control some justice, we all use them yet no one showed us how properly 👍
Best video on how to setup the DumboRC
Thanks bro much appreciate your comment.
How to video’s are great! I own 6 of these remotes. I love them! I have never set endpoints, thank you for the info!!!
Well with your end points set maybe you'll gain some extra speed or better handling. Thanks for the wicked comments dude
Thank you so much. I had no idea it was possible to adjust chn3/4. Now my shift servo is perfect!!👍😁👍
Best comments to read, no breaking that anymore 👍
👍👍👍Thanks alot. Been struggling to find some info on the dumborc 6ch and yours is the only video with a proper explanation. Awesome I fo dude 👍👍👌
Oh cheers dude really appreciate that, yeah clear info is ridiculous to find considering how popular these controls are.
Glad it helped you figure it out.
Thank you so much for this video, my friend, all the way from Pontiac, MI USA. At first I was having some hiccups. I was doing all the calibration correctly and at first had throttle but no steering and thought my servo was crap, then I didn't even have throttle and couldn't figure out why, so I put everything away for the evening and watched your video again. Then the light bulb went on over my head and it occurred to me that I had both proportional control dials turned to zero. Now I can sit and enjoy the evening knowing it's sorted out. Thank you again for this clear concise video on the DumboRC X6 package.
Your story is very close to my situation that led me to do this video.
It's super frustrating when you know it's something simple your overlooking.
Nice you put it away and let the information filter through, them blam in the bag sorted it. Glad this helped bro and thanks for the comment
Thanks. I didn't have any issues with this at all out of the box. I even setup rear steering on channel 4 with no issues. I did notice the directions weren't very clear and was just curious about the programming mode. You explained everything well.
Excellent 👌 a true success story with rear steer that won't snap itself or the servo.
Great control but no so clear instructions.
Great explanation, easy to understand, much better than the manual, thanks
Appreciate your comment 👍
Cheers mate, my institutions were wrong too!!!
If it helps, then its a win cheers.
Great video !! Thanks for taking the time to make this
Not a problem bro, these things can be tricky. Thanks for commenting and I hope it's helped you.
Well explained. Great video.
Thanks dude.
The help I was looking for ! Thank you very very much!!
Glad it's helped you dude
Thanks for this video bro, greetings from davao city philippines
Wow long ways away, thanks bro appreciate it 👍
Great video!! Thank you, that absolutely explained what I needed to know.
If it helps, it's a win for me 👍
Thanks man. Really helpful!
Awsome bro happy days 🤙
Thank you for this video. I could not make head or tail of the enclosed instruction sheet. I now understand how it works.It certainly helped me being as I am a novice RC Car builder.
It took me ages to figure out anything on that infuriating sheet. I didn't think I came across well but glad I do lol. Thanks for the comment and support
There should be a company that the "overseas" companies could hire to translate Chinglish to Standard English. :)
Better if you could scan the instructions into Google translate, job done for anyone 👍
Thanks for the video, I will do exactly the same on the weekend as you just explained it so well. it can't be that difficult now. Have a nice weekend Lg Max
I forgot to shout your name out as you asked for the video but I'd if butchered saying it lol. Hope this helps and the little trouble shoot part incase you run into issues.
@@mehimrc1314 yes, thank you, the video will surely help me. If I need help, I'll get in touch, thank you for the great video on CZcams that was not as good and informative as yours, I can start rebuilding on the weekend because I have the same setup. Lg Max
Thank you. It was very helpful!
Awesome news 👍
DUDE I THINK YOU JUST SAVED MY BUILD!!!!!🎉🎉🎉🎉 I got the x6 to upgrade my ridgerock crawler . I’m using channel 4 for my rear servo and I’m hoping what you just showed me will allow me to program my stead modes(front only-rear only- crab- all wheel) thank you so much
Hopefully dude if channel 4 can be set to centre first then left, right and straight should work great. Fingers crossed for you dude let me know how it goes 👍 appreciate you watching.
Lol
Well there in lies the trick
When I have channel for all the way back ( towards operator) it’s straight click on forward it turns all the way left but then the next 2 clicks don’t do anything. But everything else you said worked so thanks for getting me one step closer . Really new to the hobby so I’m stoked there’s guys like you out there sharing these tips!
Meh why channel 4 doesn't work how we want is crazy. Well one direction it is then 😂 sorry it not a Yippy moment.
Great video, thank you so much!
Appreciate your comment dude, your welcome.
Thanks for your video and your time I figured out how to control chanel 3 and 4 🙂👍
It's great when you can use the full use of your control 🤣 glad it's helped bro and I appreciate your comment 👍
@@mehimrc1314 yes I read the leaflet 8 times and didn't understand 😆 but with your video you explained simple and clear thanks a lot again
So helpful mate, trying to look at instructions and work this out Is a nightmare, the channel 3 and 4 so helpful as use my channel 3 for gear change on crawler 👌🏻
Nice one dude glad you got channel three hooked up for gear change. The instructions are insane, thanks for watching hope it helps some way.
Great video. Really useful.
Thanks 👍
Nice to see a face to the name, I see You also smashed that 100 subs then! Congrats dude🙏🏼
Whilst I’m here, awesome thumbnail😉✌🏼
Passing tips/advice and not showing my face was playing on my mind dont know why but that's Me. Yeah dude got past 100 subs thanks for your support and it's a great thumbnail you can get the shirt here. rcunexttuesday.co.uk
@@mehimrc1314 You true Leg End👊🏼
you are a legend mate
I'll take that 👍 glad it's helped bro.
Thanks you so much I qas about to throw a fissy fit at the suppliers . But thanks to your very informative instructions I now have a fully.working bumborc with gyro
Thanks mate. I think they should pay you to send this video with each purchase lol. Thanks buddy great video
Thanks dude that's one of the biggest compliments I've had. Much appreciate your support and I'm glad you've got it working.
I just subbed! Thanks again!
Sweet dude
I cannot thank you enough for this video!! The instructions from their website are trash
Oh boy your not wrong about the instructions. Thanks for the awsome comment.
Great vid, thanks!
Hope it's worked out for you 👍
Thanks alot thats a very helpful video very useful 👍
Great video thank you for sharing easy setup
Glad it helps 👍
Very helpful, will be using this for end points on a servo on 2 speed gearbox. Channel 4 switch is ideal with 3 positions for low, neutral, and high gear
Great to read you'll find a use for this control as channels 3-4 are now worth something 👍
Thanks 👍. I can now use the 3rd channel on my dumbo RC to control the gear that shifter properly
Awsome news dude 👍
Very good explanation! Thank you very much
Hope it helps your welcome.
@@mehimrc1314 It helps a lot. The manual is really confusing...
@@cesarinocente1703 your not wrong mate that manual needs rewritten on all Dumbo controls.
Great video 👍👍👍
Hope it was understandable and thanks for the comment.
I love the video thank you.
No once your end points are set with one car, your good to go each time. If you use the control for another car, then you might want to reset end points for that car.. hope that answers your question thanks for the comment
Excellent description 👍🏼👍🏼👍🏼
Thanks dude glad it came across well.
@@mehimrc1314 veeery well dude, the only video I saw that explains the x6 with the gyro receiver in good easy & sequence, I knew everything aboutt it. No need the check or search anything else, really well done,,, salute ✌🏼
thanks that was super useful marra
Glad it helped 👍
Thanks for the video, I tried the instructions and couldn't figure it out, watched your video and fixed it immediately
That's epic mate, what more can a man ask for haha.
@@mehimrc1314 thanks man from Colorado! does the receiver have to be facing a certain way to get the gyro to work? sorry I'm a noob
@@denvermatt not really tbh mate but have a play around and see if your notice a difference. I tend to keep the receiver at the rear of the car. How else can the gyro tell if the rear has stepped out if the receiver is at the front? Logic or madness haha.
My god thank you for this video you angel.
@mehimrc1314 I have a question I bought a team associated rival mt 10 used with a few up grades including a dumborc x6f and I can't seem to get reverse it's not the esc the esc has 3 settings,race with no reverse normal with all settings maxed and trainer with all settings at half it's on normal and I cat get reverse I watched a few videos but could not find any thing got any ideas🤨
Cheers for this-im back active again and just got a x6 and had the twitchy problem. Sorted now. Couldnt suss the "instructions"
More than welcome I tried to cover as much as possible. Glad it's helped and your back in the game bro 👍
@@mehimrc1314 Got an Eachine Eat14-thats what i stuck the receiver in-also got a 3s typhon Black Friday £325-fucking awesome bit of kit. No more WLtoys or JLB for me😁
Dude you'll love the Typhon it's my go too, I treat the cheetah like crap so much fun. Those Eachine14 look good same car but quality might be different. Any way dude £325 is a steel, I got hammered with shipping big rock £330 plus £70 shipped. I should of new something was up. Live and learn bro
Thank you Thank you big time. I put my points at 25%, rebutted my transmitter. Put throttle to 50% its alittle faster than 100% wow my car flys. Steering at 50% is perfect for me and the track I use at the hobby shop with my 2wd slash with LCG chassis.
Nice dude this is what I like to read. Glad your cars performance has increased and you can really give it some at the track.
@@mehimrc1314 I'm getting another one red or green for my drag slash. Its all esc setup in drag not radio.
@@cows1990 drag racing isn't something I'd know specifics about. But it's all interesting to me none the less.
Most appreciated !
Thanks bro
Bro thank u just seen ur video thank u so much bro
If it's helps I'm happy dude cheers for the comment
Great video thnks
Hope it helps you in some way 👍
Thanks for doing this video, had proper brain fart this morning 😂
Most mornings for me 🤣 glad it helped you out bruv.
@@mehimrc1314 😂😂😂👍
Who needs instructions with youtube! Lol thanks again for your how to videos
Much appreciated comments dude, took a little figuring out but once I knew the system. It was best to make a video thats easier to understand than the instructions.
I’m trying this now. Sorry for all the comments, just wanted to thank you again. I will let you know if I c as n get it working right. The instructions are garbage! Lol thank god for you figuring it out!
Your welcome dude and don't worry I love a good comment or two haha. Fingers crossed you'll be up and running in no time. Thanks for your support.
Just got 2 Dumbos for this dummy all the way in Indonesia. One car done, runs great, what an improvement from the stock radio. The only issue is that the steering trim is reversed? No big deal I guess, I already reprogrammed my brain for that. Thx for the video.
Trim is reversed hmm maybe you set the servo up with the channel on reverse? Like you say it works thats the main thing really happy the video helped.
@@mehimrc1314 Yes, ch1 is reversed for my physical servo layout. You would think the trim will follow the reversed direction? I got the range and response now, so all good. Thx again.
@@pawelwolski1316 sweet dude one little thing can be overlooked. Glad your happy my friend
Best explanation of how to use this transmitter kit! Thank you!
I was wondering if there is an accessory channel for running lightbars?
Channel 3 would run a light kit, BUT you will also need a light switch. Cheap on eBay, it plugs into the receiver and the light bar plug into the switch. Then on/off should be achievable from the control
@@mehimrc1314 thanks again!
thank you Batman!
Batman hmm ok thanks dude
That remote has a lot more adjustment then I knew about. Great remote fore the money!!
For both x4 and X6 they are fantastic controls for the money like £26 last I checked
Hi there do you know what the channel 5 does?
It's just another channel for YOU to decide what that channel does👍
@@mehimrc1314 i see, we talking bout the pot besides CH 6 that controls the gyro sensitivity right?
Cuz in the manual they dont say anything about CH5 while its there
Thank you so much! Fixed so many issues I had with this controller from factory. Question though. How to adjust ch 5&6 endpoints? Also with a servo on ch 5 or 6 for me when powered on they move a bit on their own. Then again when requested with button. How to stop them from self moving?
I don't believe channel 5&6 have endpoints, only channel 3&4 can be set like that.
I don't fully understand you last part, are you using a button version control (no dial). If so the buttons only act like on/off switches.
Thanks!!!!!
🤙 no problem
U have a new sub bro thanks
Every sub makes us smile Cheers dude
Well bud I done every thing on my arrma kraton to get the gyro to work but it won't work bro not sure what the problem is hit the we botten 3 times it's going light green but still doing nothing bro lol but I got the end points done so I'm happy 😊
@@samcourtrc6767 hmm the control is bound to the receiver but the gyro won't work. I guess you've got the gain turned to full on channel 6, glad to read your end points are sorted. But I want that gyro working lol, What else you tried?
Me Him Rc every thing bro iv tried to turn it of and on iv on plugged the servo and plugged it back in
Even done a factory reset as well bro
Thanks 👍
Your welcome hope it helped
@@mehimrc1314 👍
Thank you so much for this video! Last night my Typhon went flying off my table even though it was on a platform! Was going to return it but this video gave the Dumborc a second chance.
Oof I imagine that was an eye opening event. So glad you found how to fix the issue, thanks for your comment and support 👍
good video thanks . Have that 1st radio failsafe for battery loss?
If your batteries in the control are running low the light flashes on the control. Change ASAP, If you run out of range (500m) the car should come to a stop depending on how fast you were traveling you'll crash.
You did everyone a favor! Thank you! 😊
Is it possible to set endpoints for channels 5 and 6 in the click-buttons version?
You could try the same process as shown, then try the channel once you've set the limit.
Not knowing is only a try away 👍
I definitely learned something but after putting this setup on my Traxxas rustler it goes but it lags and I have no reverse?
Cheers dude just wondering Can you calibrated your ESC? For the control end points. That might get your reverse working again.
Have you tried EPA less than 100% for throttle and steering by not going to stop points on the controller? Just a thought. That way you could have les than full beans acceleration without affect on braking…
if you watch the video, when you dont hit maximum EPA, It seem to put the steering into a rage. So acceleration might be sketchy too, other than that you can adjust everything on the control.
Great help. If u have multiple receivers can u make changes to each car and have it remember the settings?. Or what u adjust on one receiver will be the same on all cars??
Unfortunately the control doesn't remember the settings. You have to reset the control to neutral end points and channel direction before changing to another car.
Good video love it very informational. And what you got.in.that little.beast for electronics ie: motor????
Glad it helps, this is running some nasty cheap 80amp ESC with a 5200kc motor. Got 66mph out of it so far I think that was 3s
Great video, I have a question regarding the adjustment dials at the top.
My throttle wont go to zero, I have to have it turned to 3 on the left before it stops driving forward.
Is there anyway to neutralise it so the dial is on zero?
Couple of things,, have you calibrated your control with all dials at neutral position?
What ESC have are you using? If possible change your neutral range position.
Hope this helps Darcy 👍
@@mehimrc1314 I've tried calibrating the remote with the dials all in the neutral position and also with it at the position 3 and winding it back to netrual while holding the throttle on while calibrating it.
It works fine in its current set up, I just thought there might be a trick to it.
I have the quicrun 16bl30 esc.
It's in a wltoys 144001
@@ThyDark0ne throttle on while calibrating that's sounds odd but I get what your explaining. There is a trick happing because your car should sit bloody still and the remote should be at neutral position, hmmm have you changed the neutral position on the ESC? I'd like for your set up to be correct 👍
When I turn the Gyro on i get less steering angle, any fix for that ?
Rebind the control and the receiver by holding the button down on the receiver untill it flashes. If not it could be static/emf from the electrics. Also possible faulty receiver?
do you know if it is possible to have channel 3 just turn off and on? like for lights to turn off and on
It think that's possible depending on how your lights are set up. If you have three wires going into channel 3 ect.
So if you have a micro switch on your lights channel 3 Should work as ON/OFF.
I had set up my crawler with a winch. Used channel 4 first. But it would slowly "drift" and pull in the winch line(already snapped it once)
Not positive this is the info I need but I'm going to try it.
My transmitter is almost 4 years old now, and without touching the steering at all, if you lightly shake the controller, the steering wheel is loose enough to let the steering servo twitch all over. Been happy enough with it up till now, but I think it's time to upgrade to something where I can adjust the deadband.
Go for a flysky remote try something different. DumboRc haven't got complete end point adjustments for steering or throttle. Just channel 3-4 can be altered. So like I say try a flysky or something abit more crawler friendly
is there a way to adjust steering (channel 1 ) endpoint left and right separately ?
Nope 🤧
I have esc plugged into channel 1 receiver, and servo steering in channel 2. Is this correct? Seems ok so far, but have only used it twice yesterday.
Certainly is dude, all good with your wiring.
Do you know how to set up the fail safe /runaway protection?
Your not the first person to ask this, I don't think these controls have that feature. I could be wrong but I'd look into it a little.
I ordered the dum x6 I see u have 14001 I actually need recomend I have 120019 I wanna order a servo cause the servo I have is 5 prog one I believe with dum receiver has a 3 prog. Also what kind of wing u get and those tires. If u can answer it be great help.
The wing is the stock wing just cut the back out. The tires are (contact foams) (32sh) is the hardness. The servo is the JX PDI 1181MG
There you go dude hope that helps
Hi, a very good explanation of the Dumborc TX for something that is not easy to decipher from the manual, do you know anything about mixing of channels 1 and 2 in regards to controlling 2 motors? as my understanding of the manual you connect 2 ESC's (and 2 motors) to channels 1 and 2 which will give you differential steering which is fine for a tracked vehicle but I would like the TX to not only control 2 motors but also control a separate servo to control the steering as well! I don't think this is something that the 6 channel Dumborc can do but hoping I'm wrong LOL what are your thoughts on this? thanks in advance.
Honestly I havent tried to mess with duel function this video was mainly for standard set up and how to get out of duel mode if your stuck. Sorry I cant help maybe try "Martyn crease" channel he plays around with duel motors ect.
I have the dumborc transmitter 6 channel. I have a problem with it i noticed the throttle trigger is being so touchy and makes my rc run itself i have throttle at 0 and when i shake the transmitter side to side it flicks the rc with its wheels and also in trying to go in reverse. I would tap it alot to get it in reverse. I tap my transmitter to make it stop. And also goes forward and im holding brake and if i let go goes forward and its frustrating because i spent nearly 42 dollars for this remote. I tried the steps on the video but my car kept going off on me and made it frustrating to do it.
Have you calibrated your ESC in anyway? If your neutral position has been moved it can effect the remote calibration. Set esc to default setting and retry the remote control calibration 👍
Great video. I have a question about the V4.. After the radio steering and trigger is set, how do I keep my Ch1 Servo from hitting the car or front suspension?
Thanks
I don't understand that last part, so you've set the control and everything works. But your servo is hitting the car? Or front suspension? Have you got the arms on backwards? I'd like to help.
The front of turning so good that it's hitting the arms
Use the duel rate dial on the remote, turn your wheels fully one way. Hold the position and use the dial to decrease steering angle. Just untill the wheel stops moving, now turn the wheel to the opposite side, repeat the process untill your happy the car isn't over steering I to the arms.
Thanks man! Much appreciated
Is the dual rate part of the steering, trigger mode?
Great video, really detailed. I might have a good question for you.
Got a weird thing happenning with one of my dumborc receivers.
Fail safe settings are the issue. After i turn off the transmitter before switching off the ESC, the receiver applies throttle to the engine. I cannot find any info on the web how to reset or turn off these fail safe settings.
The receiver is a X6YC(G) if that makes any difference.
Funny beacause it doesnt happen on my other receivers (x6f & x6fg) while using same x6a controller ( i already followed your instructions to reset the controller )
Any help higlhy appreciated 🙏🙏🙏🙏🙏🙏
Wow that was well wrote, great to understand someones issues and what they've already noticed.
Personally I have ZERO knowledge of this (X6YC) you speak of, but from what you've wrote I'd say the receiver could be faulty. BUT you do say you turn the control off before the receiver, that's a no no you should know better 🤣
Maybe your getting some residual power from the cap packs of the ESC that's powering the receiver and with no control it will do as it pleases.
Turn the car off first, then the control see if it still happens. Electrics cars can still have run aways but only in my opinion if the receiver has gone/faulty.
Hope this helps and thanks for an easy read 😊
@@mehimrc1314 Thanks ;) Haha yeah i know i know its a nono ;) i do it only on the bench ;) but this realy got me surprised. It's a nono indeed, but imagine loosing signal or battery power in the transmitter while driving, default shoult be that it swithes to neutral, in my case the rc would drive itself forward. So far i managed to find some info that it's the fail safe settings. But no instruction or knowledge how to deal with it ( reset receiver settings or change to neutral on signal loss )
@@mehimrc1314 The only thing left i can think of, is hitting up Dumbo directly - hope their after sales support is any good.
Can you give your car more steering? Just installed the received and it was easy but it seems the steering might need more steering, its kind of wide steering
On the x6f receiver yes.
if you have the x6f-G receiver I don't know.
My max 5 didn,t get any signal from the receiver pluged the esc to channel 2 and steering to Channel 1 also Binding up the transmitter with the receiver what did i wrong??
Could be a faulty receiver.
Hey thanks for your Video. I followed your explaination. But i have still a problem after calibrating in normal mode. I turn the steering to 100% but i only get about 60% steering. Any idea what i can do?
What receiver are you using (x6fg or x6f?)
@@mehimrc1314 x6fg
Are your duel rates and dials set to 100% before Calibrating?
@@mehimrc1314 Is there any effect when i calibrate at different positions?
At my dumborc not.
Yes there more than likely is a difference, that's why instructions are set to follow.
Also try rebinding the control to the receiver with all duel rates at 100%
Is there a way to save deadpoints for ch 4, I regulate how far I want them in setting mode and all is fine, but as soon as I turn off remote, the car just reverts positions and keep on breakinf stuff, in my cace gearshift on my rc crawler.
Strange mine always needed reset, the control automatically left my setting as I set them. Even when I switched the control and car off, unfortunately the control hasn't got "save" button as such just a setting menu you enter and leave. Sorry I can't help further than that 😞
Thank you anyway, will try order just reciewer,mybe faulty,@@mehimrc1314
Hi, first of all, geat video, very educational.
I was wondering can you help me. I have a problem with my Dumborc x6 transmitter.
On channel 4 I have a winch motor, and when I turn of the transmitter (ch4 button is in the neutral position) my winch motor turns on and I can turn it off, only if I unplug the receiver for the power.
I have done some research online, and it seems to me that there is a failsafe on ch4 that activates when I turn the transmitter off, buy that failsafe is not setup to be in neutral position.
Do you know how could I solve this problem?
Thank you in advance.
i just got one of these an put in a car that ive 3d printed. the motor trys to go full throttle tho when connect to the transmitter. i can push forward to hit breaks or reverse an it will stop but ive not been able to figure it out. im new to all this stuff an the instructions that came with the transmitter are very limited an dont explain anything that i can find that will help my issue. suggestions?
just hooked it to a esc, motor an servo out side of the car an it seems to work fine. i had to adjust the trim a very small amount for the throttle to get it to not spin the motor. i hope the motor is good cause i picked it up a couple months back an have just not gotten around to try it an if its bad out of the box i dont have any option of returning it now.
Sounds like you managed to find the solution yourself, always check your trims 👍
I’m planning on using channel 3 for lights and channel 4 for my winch. Will this work?
Why won't it work? If your lights have the correct wiring loom then yes channel 3 will be on/off or multi function depending on your light set up. Channel 4 should be perfect for a winch, make sure channel 4 is set in the centre position before connecting your winch.
@@mehimrc1314 ok thank you for the help
so we want to set throttle and steering to 100% when we are ready? you went over channel three and four but i thought steering and throttle were channel 1 and 2 lol. i'm confused, so bad at electronics
Your not confused, channel 1 steering and 2 is for throttle. Go into setting mode and move steering left/right then let go. Do throttle next go full acceleration/full reverse then leave the trigger. Press channel 3 to save settings then turn off the control should be easy harder to explain in text format.
@@mehimrc1314 I see, I think I was getting confused about knobs. I thought they had to be "set" in a certain position before leaving the setting mode. It sounds like they just adjust the position of steering/throttle based on where you set the end points.
Thanks again, thank you! I'm subbed now 😀
anyone know how to make the channel 3 like a button instead of like a switch? so instead of one click and stays blue it makes it only blue when im holidng
Sorry to be so blunt but not a chance 🙃
Do you know how to reverse the gyro action? Mine steers opposite the skid instead of into the skid. Thus my car spins out easier as I turn channel six up higher. Almost impossible to steer with gyro at full sensitivity.
Turn channel 6 to the max,then on the receive press the button in twice. This should fix your nightmare dude
@@mehimrc1314 That worked, thanks a million.
@@charlesbeshaw9843 that's why you came here Like,and share dude. Always a pleasure
Can i bind a x4 to a gyro receiver and use the gyro?? Or do I need a new transmitter
Unfortunately you need the 6 channel control for the x6fg gyro to work.
Other way round the X4 receiver can bind to x6 control with all functions.
@@mehimrc1314 o ok , I'll order it thank u
So EPA is not possible for throttle and steering?
You've got dual rate adjustment for throttle and steering. I've not tried to find an end point with in setting for steering. Possibly could be there just not found, channel 3/4 have EPA adjustability.
@@mehimrc1314 Yeah, but DR adjust bothleft/ right, forward/ reverse at the same time. I want to be able to adjust each way separately
Get an SLT3 with the receiver you can you do that on there. I haven't used many other controls
ey man, any idea why my X6 Gyro has the blue led blinking ( slowly) ?? Everything works ok even the Gyro , it started few days ago it blinks with car on and with car off . ( 124019)
The X6FG receiver should only have two lights either (green, normal mode) or (red gyro mode) so I'd need to look further into that.
If it's the control blue light blinking, change your batteries but I'm sure you'd know that.
If its still working thats a bonus, could you tell me what receiver you've got?
@@mehimrc1314 Yes , my X6FG with Gyro on has a green light , not red but it works , I thought it was related to batteries and I checked one of them with a multimeter it was not too low voltage as expected but I changed all into a new fresh batteries and problem solved :D thanks man
Awsome what better way to start the day then solving a problem.
Happy days bro 🙂
Does the receiver have to be placed in a certain position for the gyro to work?
Not really but I prefer the rear or the car of possible.
@@mehimrc1314 Thanks for the reply
I don't have brakes or reverse and I already recalibrated my esc help. I've fixed the problem. My throttle trim wasnt set right. Good vid tho
Trim should be set to neutral point/zero and duel rates should be set to 100 before setting anything. Glad you fixed the issue as it was so minor.
@@mehimrc1314 How exactly do you fix the brake and reverse issue???
I've never had a brake or reverse issue with the control. Only the ESC not being set correctly have I had braking/reverse issues.
@@mehimrc1314 sorry I've only seen this now but the controller won't work with my esc. There's nothing I can do. Everyone that has the same setup had this problem
my throttle and reverse are backward, I can't figure out how to change it.
Swap any two motor wires around if your not running a sensored system.
@@mehimrc1314 Hey thanks for replying, Its a sensored Motor but its not hooked up as sensored since my ESC isnt capable. its my first RC, I hadn't read your msg yet and I didnt know if that was the issue since i have it hooked up correctly, A B, and C. Should have tried that. Anyways, what I ended up doing was flipping the differential ring which worked, its front motor/RWD MST FXX
@@NARFALICIOUS nice well I'm glad you have fixed your probelm bro happy drifting.
Awesome video. I just have one q. I can't seem to get an answer to . I plan on using this in a boat so gyro control isn't really a concern but I would like to use the channel 6 just to be a proportional servo to control say an operating anchor. So if I got the version without gyro or turned it off ( as you showed) can the channel 6 do that? Thanks
Sure thing dude plug a servo into channel 6 with the gyro off and it should work as you wish. You have to remember where you set channel 6 on the contro before plugging servo into the reciever channel.
If you want to control it one way to the other, eyeball the dial at centre before plugging servo into channel 6.
You can have the gyro on and still control a servo with that channel, it doesn't take over both servos but trades the gyro for the movement, if that makes sense. Hope this answers your question bro
Ok great because I'm restoring like a 40yr old RC boat none of the RC equipment matches anything today so to know I can just star over at good price sounds great thanks
@@plutoyaldnil4750 not a problem dude good luck hope all goes well with the restoration.
Oops lol just saw the have the lighting option. Not it seems they want to sell that with new transmitter where channels 5&6 are just switched I want proportional is there a set that will get me that sorry for bugging you but you really seem knowledgeable
@@plutoyaldnil4750 it is proportional, I've just tested this on my reciever with the light function ect. It works fine, in channel 5 or 6. like I say, it's about where you've set the dial before you plug into the reciever in. The Control doesn't have memory so you have to do the remembering haha.
Hope this helps dude questions need asked.
Are you able to adjust 3 4 5 or 6 channel with vehicle on? Because guessing the 25 percent or such for servos would be a pain. With vehicle on, you could fine tune to where you need them.
Channels 5-6 I have messed on with yet,, at 8:09 I explain how to change channel 3-4. I wouldn't do anything with the car on. It's a case of,,, On off on off unfortunately dude..
You can change to order of the buttons in the settings something I'll never do but you can
@@mehimrc1314 yeah, it's something I'd like to try. Like end points. Cause on a nitro, servos don't always need full 100 percent.
@@jakec79 you running nitro, ah well you'll want to be carefull incase of a run away lol. What is it your wanting to do?
Not just nitro, but I grabbed two old traxxas models that have the 27mhz systems. They need to go, so with this radio setup, I need a third channel for reverse. And I need end point adjustment on throttle and brake and reverse servo.
But I wanna be able to do it with the servos active, so I can fine tune it for the throw.
@@jakec79 throttle adjustment can be done via the throttle trim. You can add a servo to channel 3 or 4 and adjust end points like in the video for your reverse. I don't do nitro but I looked into what your asking. Hope this helps if not I'll learn with you.
How do check the built in FailSafe? I cant find info anywhere
The fail safe is set by hitting the bind button once light will flash, then within 5 seconds press once again.
So car on, control on. hit bind once now choose full throttle, neutral, or brake, now hit bind within 5 seconds.
This should put the car in your preferred safe position 👍 and if it doesn't work write a strongly worded email to Dumborc 😂
Thanks for this.
Can you set forward/reverse for channel 3 and 4 in the settings too?
What we talking, like for a winch forward and reverse?
Channel 3 is just a button so no setting that. Only on/off unless you've got a module with multiple functions channel 3 will toggle them.
Channel 4 maybe if set to the middle position before setting up control. Maybe possible to set something to that channel and have a forward/reverse function.
Guessing why your asking is a tricky business lol 🤣 hope this help brother
@@mehimrc1314 i'm just wondering if you can reverse servo direction on channel 3/4 in the setting menu, where setting endpoints. Do the switches controlling channel 1 and 2 direction control channel 3 and 4 in the settings menu..?
I'm waiting for servo to come in to control shifting in a crawler.
Want to set it to button ch3. Use the remote for different cars, so would be nice if i can set which gear it is in when button is off, if that makes sense.
@@leovandijk8852 Makes perfect sense bro, the lower trim dials adjust channel 3/4 not the upper ones in menu mode. For gear changing channel four is your go too button if anything, channel 3 won't do jack for that, its on or off. Reversing servo on those channels isnt possible, same as the steering servo. Once in the trim is reversed if you've noticed lol.
@@mehimrc1314 dont understand your last line.
Anyway, thanks, all i wanted to know.
I can use ch3 btw, just 2 gears
Channel 3 no channel four maybe yes.
Hi mate, my dumborc 6x radio change the blue light for a red light and now when turn the wheel the rc turn and go forward at the same time. I have no idea how turn the light to blue again. Do you know how?
Thanks
Yeah sure dude,i know what you done. You've went forward on the trigger and forward on the steering then hit power. That's duel mode. Do the same again but when the light flashes pull the trigger back. It'll turn blue then turn it off dont hit channel three. Then enter setting like I did trigger back steering back then power on,let go then hit channel 3. You'll set your ends points as in the video.
Oh and hit me up once you've tried dude
@@mehimrc1314 men that was the solution! Thanks so much, have a nice day!
@@hobbiejoechile6532 your welcome dude glad i could give you the solution.