Geeetech Prusa I3 pro B 3D Printer DIY kit assembly [time laps & photo]
Vložit
- čas přidán 13. 01. 2017
- Time laps and photo of building 3D printer Acrylic Geeetech Prusa I3 pro B 3D Printer DIY kit.
I bought it on ebay for about $200
For wiring (connection) the elctronics (gt2560 board) watch this video:
• GT 2560 board wiring d...
Thanks for watching.
Music:
The Only Girl - Silent Partner
Santo Rico - Twin Musicom
Payday - Silent Partner
Skladba Santo Rico izvajalca Twin Musicom je licencirana z licenco Creative Commons Attribution (creativecommons.org/licenses/...)
Izvajalec: www.twinmusicom.org/ - Věda a technologie
Good work!
geeetech thanks, really good printer for that price, waiting for avto bed leveling sensor...
very nicely done.
builtrodewreckedit thanks man
I brought the CTC DIY. I did get it to work a few times but the print outs are ng. Yours look great. what software did you use? I used Cura 4.5 Printer set to PRUSA I3 Pro B and used the Prusa i3 MK2 setting and I used the CH340 drivers. Do I have the correct settings? and the hot bed has a problem.
I mostly use s3d slicer, about printing you just need to playing with different settings, a lot, so you figured out what settings make wich difference, calibrate everything and than you will get nice prints.
To clarify - the x-axis-stopper is the stopper, that is attached to the x-motor?
Because the video and the manual have different colors for the cables (you only see the cables in the manual in the last steps for plugging), so I am a bit confused which stopper is supposed to be where.
Especially because we first build the Y (red), then the X (blue) and then the Z (black) stopper. But in the manual, the plug in order is x, y, z - (red, blue, black).
I now plugged in at the following order: blue, red, black (x-y-z).
Is that right?
Kobrabiss hello, it doesn't metter how you connect, you can choose red for x, y, or z axis.
Please chack my other videos, i got one about how to connect/wiering the gt2560 board.
Thanks for the fast answer, I will check it out
Kobrabiss no problem, tell me if you don't find them, i will post into description later.
I have now assembled everyhing right I think.
Have done the setup and fixed the Y axis in the firmware (turned wrong direction).
Now I started the first print and it looks like the gear in the printer isn't turning at all. He only prints, when I manually press the filament in. He isn't pushing it out tho, so I don't know if its the firmware..
4:11 Ah, you got lucky, I was one of many who's brass nuts holes didn't line up with the black metal part.
hello tintek33,
I would like to ask you please :
1- which 3d printer is better the single rail or dual rail ?
2- is it possible to make plugs for finerglass molds with this printer ?
Hy,
1: i don't have enough experience with 3D printer to tell which one is better, but i think dual rail, i just buy the cheapes printer :)
2: of course you can make a model, or whatever you want, the best result you got if you print from ABS, grind them with file and a sand paper, then smooth the model with acetone (search youtube) i got some really nice print out with this process like it was from injection line.
ok perfect thank you :)
Buenas, quería saber donde podría encontrar el paso 28, el cableado, ya que tengo muchas dudas y creo que me faltan cables. Muchas gracias
do you mean that:
czcams.com/video/sqQI_-4UNp0/video.html&t=
Where do you download the driver for this? I can’t find it on the original website neither geeetechs website
www.geeetech.com/forum/viewtopic.php?f=10&t=17046
5) Firmware for I3 pro&proB
I3 pro&proB(GT2560)
Marlin-PI3_Pro_B.zip
How low/down do you set the long screw on the left of the printer that pushes down on the Y limit switch? 3:56
boowonder888 you mean z axis limit switch, you set it after assembling, just that much that noozle got for a paper free sace from the table glass.
I think I understand. So the screw ends at the same height as the nozzle after I set it with a piece of paper? Thus the nozzle cant hit the glass because the switch will activate to stop the nozzle from going down any further?
I just assembled the plywood version. It is my first printer and I'm getting ready for my first print ever. how do you like yours
boowonder888 yes, but tight screw till end first so you don't break the glass with nozzle, than unscrew it until.get perfect ned leveling.
I think that is great printer for the money, it's just need a few modificatiom and aetup and work just fine
This must be a precise and quite dangerous job then. Because it has to be done right on the 0.5 mm {business card thickness). You have to do this by eye and you need to be spot on. If you are off by even 1 mm, the nozzle is gonna hit the glass, right? This should have been explained better, cause it is critical, don't you think?
no video on showing where the wires go? it's no trouble but would like to just make sure i've got everything set up properly.
there is have to look for it i seen it
Have type wire set up for it. U see just go threw the video make sure u type ur type of printer
sir i build a similar printer but my print is not good.the part is soft and easy to break.what should i do
online sale it's hard to say what you do wrong, there are tons of settings, try to play with it.
sir can you give me your email
i m having problem
1.my product is printing small.means i m printing 15 mm cube.but z axis is printing only 7mm.i cannot find out why..plz help me out
MONEY MAN check if you got right software uploaded to your arduino, i dont rember but i must upgrade merlin vith arduino software, i just follow the instructions come from geeetech on email after buying.
Size you can set with ppm (pulse per mm) find it on lcd acreen and try to double it for the begginning.
You can set for each axis.
Auch hier wieder der Fehler in Step 19. Die Sicherungsringe gehören nicht aussen an die Schlittenstangen der Z-Achse. Wenn man den Riemen spannt verziehen sich die Führungsstangen der Z-Achse und es entsteht ein Wobble-Effekt. Die Sicherungsringe gehören nach innen so das der Abstand unten wie oben und beim Hochfahren der Z-Achse immer gleich ist.
hello, That's how manually says i didn't think at this moment, but after few days of using i realize that's wrong and do that:
czcams.com/video/G5XpvJxJVaQ/video.html&t
nossa cara voce è o cara vou aproeitar as minhas economia vou comprar 2 destas
hi, in the part of mounting the motherboard is not clear, could you please tell me how to mount it or where to find another tutorial? I need help
Eme :3 leave motherboard on table, screw the white plastic pin onto frame and than just push motherboard onto this pin or clip.
Plastic clip you can turn only on one way (one side) because only one side of pin got hole, that hole go on frame side M3 screw go through the frame into that hole. Not big deal, maybe there are more holes into the frame than you need, so befor start screw pin on frame chack with board in witch hole you must to screw pins.
tintek33
I'm sorry, I may express myself badly. I was referring to the part of the cable connections. Thanks for answer so fast.
Eme :3 just look the manual you can't fail
tintek33 i don't have any manual... Do you know where I can find one?
Eme :3 i reaceived it on my email by the seller after purschase
André Lefranc Hello,
The assembly of this machine is not correct. The X-movement motor belt pulls towards the center on the Z axes and deforms them towards the center. To keep the two Z axes parallel, the four stop rings must be mounted inside and form a rigid frame for the two slides of the X axis.
I do that also:
czcams.com/video/G5XpvJxJVaQ/video.html
Does the I3 Prusa kit have a 110 volt plug?
Im not 100% sure, but i think yes.
oi eu aqui de novo tem como voce criar um video mostrando como baixar o soft e executar a maquina pra criar inprencao
how's the z-wobble?
Google+ SUCKS BALLS - the worst forced social network No problem, but i will make some upgread there later
Hey, really weel done, do you have the wiring demo of the 2560 board?
G. Jaehnick thanks, but Sorry I don't heave, but it's easy work, just Follow the photo on the manual and you had No problem with.
I follow the photo and it does not work, when I ask for position 0, the extruder go to the left and the nema off z still runnig even after touch the end stop, impossible to make it run.
I can send you photos or video. Please help me.
G. Jaehnick ok, if you look at the top left corner where is 6 connector for end stop, you must connect them:
top left -x switch-empty-y switch-empty-z switch-empty.
Exactly what I have. still going to the right when I leave extruder in the middle and ask for home position.
G. Jaehnick so when you want to home x axis it go to the right side?
if so you must set rewerse direction of motor rotation, it is somewher in the arduiono program, i just Follow the manual and upload the latest arduino fw, all work ok
Hi, I will buy this 3D printer, but i'm 15 yo... Do you this it's easy to assemble? There are instruction for building in the kit? Thank
Yes it is easy, i think 15yo got no problem to assemble, i got instruction manual and link with software and everything i need to make printer work on email day or two after buying on ebay, but there is also manual and everything on internet, i got another video how co connect all the electronic...
TinC33 ok thanks
mine when press home it goes then it makes lot of nosied grinding like before it stops aftger it touches the end stoppers
But did it activate the limit switch for sure?
@@TinC33 it did went in to it bounce back and back in to it with grinding noise the stop
i watch on some were there go and stop quietly mine no with lot noise when touching limited switch
@@chas290620 so the motor move the bed to the limit and then start loosing steps, check the limit switch if they'r connected right and if the bed activate them.
No they both do it they go to limited switch touch with grinding sound they back off and touch agian and shut down and my bed don't move just a little there's a red button on the board I assuming that's a reset button
Hello TinC your video was very informative and we have exactly the same 3d printer for our club (retroclub.info). Start building this week and use your video ,if needed.
dat-alex thanks, assembling is very easy, you just look the picture in assembling manual and you can't fail, if you'll need some detail i can take some photo about...
the model of supply fan on the extruder ?
Gianni Perbacco don't remember, just search "geeetech i3 cooling fan" on thingiverse, but now I use different fan and holder.
can u help me to find one i have one turbine fan, and i don't know how assemble this
I use this one:
www.thingiverse.com/thing:2039119
it's for turbine fan + bl touch
ty man
ty man:D
I regret buying anet a8, should've bought this instead!
i thing they'r preatty close, almost the same
looks like this one has better frame stability and it already has good belt tensioners too
HELP PELASE!!!! i didnt get one of the green parts on the control board, did this happen to anybody else? what do I do please help
It's just a connector, check if they'r not on cable.
Anyway it's better to throw it away, because exactly this part can make fire, so you will do much better if you just solder wire direct to pin, but be carefull on polarity.
This can also help you
czcams.com/video/sqQI_-4UNp0/video.html
@@TinC33 HI, I magaed to get the 3d printer on and everything looks good (the fans and stuff) but the screen is just green and it shows nothing am i an idiot or is it not meant to be like that
@@JustBilly123 did you check upper video, in my case there was a flat cable connector turned on wrong way.
@@TinC33 is there any difference between the sd card wire and lcd screen wire? if so plz tell me
kolko eura carine?
iceCOLDkillaxDLoL nič, ker je iz ebay.de
Do you have link for this particular eBay seller and this product? Thank you in advance. Pozdrav iz hrvatske.
WildMania pozdravljen, just go to ebay.de and search for geeetech i3 pro B, thensort by lowest price + shipping first, i buy grom direct seller geeetech, because of lowest price.
Oh, thanks - I found it. €199, free shipping. (or less, but then added shipment cost to Croatia). I am just waiting some money to arrive... then... well... go to 3D printing. Thanks again.
WildMania yes shipping is free, ship with dhl so you got it 3-4 days after payment, and No tax inside Eu. This is great printer for that price, good enough for beginner, and there are also many options for upgrade.
ARCHI NUL : AUCUN INTERET n'aide ni en rien ni personne seulement montrer que t'es super génial et infiniment supérieur à tous ces nuls !!!
I was wondering if you had a video that was not time laps
no, because i only take photo every 2 sec. look for the user geeetech (here on YT) they got a step by step video.
This is the only video that I found that has the same parts the one on Geeetech has blue parts and are different
yes that one had some iron parts, older version had blue printed parts but the printer is almost the same, do you heave problem wit assembly, i not eaven read the manual, i just look the pictures and assemble it without problem.
The rods that connect the left and the right side do not fit in the holes on the iron parts
Aha, i remember this problem, you must use a file to increase the hole, you must grind that much that the shaft go easily threw the hole, without any force.
Try to grind as evenly as you can (grind for all the size, so the hole is still round not some egg shape)
No need for the music, lost me there mate sorry.
Hmmmmm.... Well.... It's the same product....but duuuude the framerate is horrible. .25 speed and it's a frantic blur of nonsense. Even worse this product arrived with absolutely no instructions. So matching the parts with the video is really hard. Should mark part I'd when you showed the parts. Thumbs down on the quality of video, thumbs down on the lack of instructions from the company and thumbs down on the product. At 2:09 wtf did you add? Like can't see crap....
I got clear manual with it, try to find them online.