Breakerless-SE (single wire) Electronic Ignition Conversion Kit & How to Install -

If you're still running breaker points in your vehicle, you need to ask yourself WHY? If General Motors dropped point-type ignition in 1975, why would you still be using them? Re-gapping Them? Replacing them? Even if you're a purist or a restoration maven, there's no good reason to run points these days.
Are you tired of cleaning, adjusting, or replacing your breaker points because they're burnt, pitted or worn? Are you tired of trying to keep your breaker-point fired vehicle in top running condition? If so, then it's time to get rid of your old points & condenser and move into reliable-firing, maintenance-free electronic ignition!
This Breakerless-SE electronic ignition conversion kit, Lectric Limited part # 38181.
Will it work on your vehicle? Yes. If you have a:
- GM Delco V8 distributor,
- Equipped with breaker points,
- Window-type distributor cap,
- Screw-on type rotor,
- Stock/original-type ignition coil,
For those hoping to keep an original-looking underhood appearance, and prefer the look of a stock ignition system, when installed, this entire conversion kit (shown here) fits COMPLETELY under the distributor cap. And unlike most "under-the-cap" replacement ignition systems, the Breakerless-SE installs with NO additional wires protruding from the distributor. You'll only connect your original coil wire. The result is state-of-the-art electronic ignition... with a stock appearance when the distributor cap is installed.
Besides keeping a stock appearance, here are some of the benefits of the Breakerless-SE electronic ignition conversion kit:
■ You do NOT have to remove your distributor to install this conversion system.
■ The trigger and power components are integrated into one fully encapsulated, high-temperature thermoplastic module.
■ Active Dwell Control maintains high-RPM spark energy without coil heating at idle.
■ Auto standby mode that prevents coil damage or drained battery if the key is inadvertently left in the on position.
■ Hall-Effect/magnetic sensor that is unaffected by vibration, engine oil, moisture, dirt or contaminants. These contaminants can play havoc on the other conversions have an optical sensor.
■ Over-voltage protection from high-amp battery chargers
■ Reversed battery cable protection if this accidentally happens
■ Simple installation. It will probably take you longer to read the detailed instructions than it will to install this conversion kit.
■ 3-year warranty! Unheard of for an automotive electrical part.
Since this system is designed to convert an original breaker point ignition to electronic ignition, you do not, and should not, remove either your ballast resistor, or resistance wire from your wiring harness. You'll also want to keep your original, or use an original-type, ignition coil.
The Breakerless-SE comes with everything you need to easily convert your breaker-point ignition to reliable, virtually maintenance-free electronic ignition.
What's in the Kit?
■ 2-piece vane assembly. That mounts underside the distributor's rotor, and around the distributor shaft.
■ Electronic ignition module with reliable hall-effect sensor, encased and sealed, in a high-temperature housing. This module fits perfectly into the same holes as were your points. You will not have to drill or tap additional holes.
■ Complete hardware kit with screwdriver.
■ Clearly written, step-by-step instruction manual, with helpful diagrams.
---------------------------------------------------------------------------------------------------
HOW TO INSTALL THE BREAKERLESS-SE ELECTRONIC IGNITION CONVERSION KIT:
Installation instructions will be shown at the end of the video.
The Breakerless-SE kit can be purchased from Lectric Limited, Inc., Part #38131, www.LectricLimited.com. 708-563-0400

[@paulasturi4199]

Wow! That was easy! 👍

[@alliedcatalogs7417]

I want this! Appears to be a MUCH better (and easier-to-install) solution that the Pertonix electronic ignition system.

[@brineich]

This is a slick, simple product! Do you plan to make this available for Ford V8's and possibly for 6's?

[@LectricLimited]

Thank you for your question. Currently, there are no plans to make the Breakerless-SE for other make/model configurations. We will certainly post it on CZcams should that time come.