How to Fix No Signal From Backup Camera on Aftermarket Android Car Radio.
Vložit
- čas přidán 6. 09. 2024
- 🚗 Upgrade Your Driving Experience with ViaBecs AHD Car Backup Camera!
📦 Order Now and Drive with Confidence!
Ready to take your driving experience to the next level? Order your ViaBecs AHD 720P/1080P Car Backup Camera now and enjoy the peace of mind that comes with enhanced visibility and safety.
Order it on Amazon: bit.ly/43W9pxt
------------------
🚗 Unlock the Full Potential of Your Backup Camera with ViaBecs AHD Technology!
📹 Welcome to our latest video, where we delve into the world of ViaBecs AHD Backup cameras! In this demonstration, we'll be putting the ViaBecs AHD Backup camera to the test, specifically the 10PIN camera line, and troubleshooting any issues you might encounter during setup.
🔧 Critical Step: Connecting the Short Lines
One common oversight is neglecting to connect the two short lines on the 6M/19.6ft RCA Extension Cable. This step is crucial to ensure that your aftermarket backup camera properly displays on the head unit. Watch closely as we guide you through the process and highlight the importance of this connection.
🔌 Powering Up Your Camera
Discover the significance of the power cable for your backup camera. Failure to establish the correct connections could lead to a rear view display failure. We'll demonstrate how to connect one short line to the reverse line and the other short red line to the positive pole of the reversing light, providing the necessary power to your camera.
🛠️ Troubleshooting Display Issues
If your backup camera still shows a black screen, fear not! We'll troubleshoot potential reasons for this issue. For those using the ViaBecs 16PIN wire harness, we'll show you how to easily locate the reverse line with the help of a wiring diagram.
🖥️ Optimizing Display Settings
Once the connections are made, witness the magic as your backup camera displays flawlessly on the head unit. But if you're still facing challenges, we'll guide you through setting up the Reverse camera format. Our resolution of car rear camera is 1280x720P/25fps. we selecting the "HD - Rear View - AHD720P/25fps" option for the best visual experience.
👀 Don't Miss Out!
Ensure you're making the most of your ViaBecs AHD Backup camera by following our comprehensive guide. Whether you're a seasoned DIY enthusiast or a tech novice, this video is your go-to resource for unlocking the full potential of your backup camera.
#ViaBecs #BackupCamera #CarTech #reversecamera
What if the reverse camera option isn’t available for me?
I have the same problem
A Chrysler dealer installed a back up camera on my 2015 300C. It works sporadically, sometimes it say "unavailable ", but stops working in early spring, and stays off until Autumn. However, sometimes it will work in hot weather and other times it won’t work in winter months. First time it malfunctioned was in 100° weather and I was parked with camera lens facing into the sun. They want more $ to diagnose the problem than what they charged me to install it. What should I look at first to diagnose problem?
Hello, my camera is working perfectly if my car is not started, after i start it goes black, do you know what can be the issue?
the same. I have it installed just today. it works when the engine is not started, and stops to work, when I start the engine
But i have not connected this 2 short red wires on both sides of camera's cable, and took power for camera from the rear light bulb.
I will try to connect them and will see if it will fixed it.
@@juri2rx I just talked with the producator of my head unit, they said the camera has to be connected to the head unit, mine is connected to the backlight
@@145kamikaze it is strange, that it works with ignition ON, just engine is not running.
I will try to rewire it to the head unit.
@@juri2rx please tell me if it is working, i dont really have time this week
@@145kamikaze I had noo time to check it to. But:
1st. I have found my Quick Manual, and it is written "do not connect these wires if your car comes with CAN-bus system". As I understand, one short red wire is connected in parallel to rear light, another to HeadUnit just to let the HU know the rear gear is switched on, just to give HU command to switch to the RearCamera View mode.
Mine knows it even without rear camera at all. So it is not for powering, just for command.
2nd. As I wrote my camera operates correctly if the engine is NOT RUNNING.
So, again not a wiring issue.
During the day the rear camera even 5 times switched ON while driving backward, but just for a second each time. And if the engine just stopped running without turning the ignition OFF, the camera immediately is turned On.
I suppose the problem could be in the "noise" on power line, while engine is running.
There are many posts on it, "if your display is black - try to install the DC noise suppressor."
My display is not black, but "No camera" or so was displaing
I will try to find the filter or even try to power the camera with a spare battery .
Probably filter is better, I have a gasoline car, and the sparkplugs and the coil can make electromagnetic noise.
Thank you.. Able to settle my problem with your help.. thanks again
Thank you 🙏 exactly what I needed to know 😮
What about factory camera ??
I feel this to my soul. I can’t find a single thing about a factory camera not working
If you find anything please let me know 😢
I figured it out. Factory camera is a hassle but I managed to get it to work.
@@mehxs7225HOWWW
@@mehxs7225how did you get it to work with the factory camera. ?
hi can you help, i have a android 11 radio but get no signal from rear camera no matter what setting i choose, but another after market radio i have picks it up straight away.
000000
Factory setting passwords is 8888?