Super ATV Portal Gear Lift Install GEN 2 - Extreme UTV Tech
Vložit
- čas přidán 17. 02. 2018
- On this episode of Extreme UTV Tech we install a SuperATV Portal Gear Lift kit on Project Party Wagon. Most all of us want to run larger tires on our UTVs. But this can be a hard on parts and usually take certain permanent modifications to your machine like gear reduction in the transmission or a lift kit. Well the folks at SuperATV have the solution with their GDP Gen2 Portals. They are the same as the Gen1s with one key change. Pretty much everything on the Super ATV Portals Gen2 are much beefier. Carter is going to walk you through how to install them on your machine and give his review on the product. This way you can just watch the video instead of having to read the super atv portal instructions. Then on the next episode we are going to go test them out at King of the Hammers. Be sure to hit us up with any questions in the comments. Oh and sorry about all of the background noise in the video, Rocky Hollow Metal allowed us to use their lift for this video and they are a busy and noisy shop. Hopefully eventually we will have our own lift in the shop, but until then it is what it is. On another note, Have you ever seen a lifted RZR 4 seater look this good? It looks good thanks to those GEN 2 GDP Portals and 34s.
Big Thanks to SuperATV for their help with this project- You can get this kit for your machine at www.SuperATV.com
The GDP Portal Gear Lift we installed was $2899.95
www.superatv.com/polaris-rzr-...
Also big Shoutout to Wheel Pros for hooking us up with a deal on the MSA Beadlocks. Get yours at www.WheelPros.com
They retail at $218 each- www.wheelpros.com/wheel/29893/...
The 34" Roctanes came from Dustin Robbins over at www.allthingsUTV.com (Call for Pricing)
Trailing Arms and A-Arms came from Justin Pierpoint over at www.ORBfab.com
Official Busted Knuckle Merch - www.bustedknuckle.com
BKF Facebook - / bustedknucklefilms
INSTAGRAM / bustedknucklefilms
SNAPCHAT & TWITTER - @the_BKFilms
Big Thanks to our sponsors
www.bustedknuckleoffroad.com
www.gilbert-designs.com - Auta a dopravní prostředky
Thanks for the video! I installed mine over the last few nights and the video was very helpful!
Glad we could help!
Thx for video. Did both my portals/seal change today.
Awesome, still no issues out of these
Great video guys!
Thanks! We plan on putting the test run video out soon
I really like your videos. You are a do it yourselfer. If that’s even a word. LoL. Thanks for sharing your knowledge.
Thanks for tuning in!
Nice shop
James Merritt RHMF has a nice place no doubt. We need a lift sponsor lol
I bought a new RZR Dynamix and upgraded it because of this video.
Awesome how do those shocks handle the portals?
@@BustedKnuckleVideo Awesome! My wife loves it in comfort mode
It's actually crazy how the dynamix system keeps it stable even on 6in portals and the 3-5 lift kit.
Nice! I've got to do some shock tuning on mine
@@BustedKnuckleVideo I'm sure you do a little more with yours than I do. Did you go to my channel and see it?
Portals rock.... cause they keep good shaft angles and allow the needed lift to gain ground clearance without sacrificing the strength of the axle shaft angles..
All very true, only downside is added width but I think it is worth it.
For competition and extreme park riding, it totally is. The trails are usually plenty wide, the extra width wheel to wheel increases stability.
Bill Titwell not a single racer we run with uses these. I’d like to see if the gen2 portals can hold up to the abuse of racing.
Awesome job for making comprehensive easy-to-follow directions 🤘🏼looking forward to the next video 🍻 The V2 portals look WAY TOUGHER !! But I gotta say all this video does is piss me off that I live in a state with a 60” law 🖕🏻
We will have the full blown test run video out soon!
The sunrise trail has no limit
Nor'easter Playa oho really lmao tell that to the wardens 😁 Trust me it’s 60” bud 👍🏻 I sat on 22,000$ cash waiting for a 1000 RZR4 for two year. I put on 13,000 miles on my old RZR4
thats a crap ton of miles
i see that it was also a great time to upgrade to that ORB stuff ..
It's always a good time to upgrade to ORB stuff
Tim Meeks....The Man The Myth The Legend
Thats right 😂
Excellent video.... What brand are the billet high clearance radius rods?
They are made by L&W Fab out of Georgia. We run them on all of our rigs
We really want to see the k5 finished though...
kapes5nine the engine swap vid is coming soon!
dang son im an old disabled mechanic and i would have liked to see everything tightened with a torque wrench,
It's not an engine so we use German Torque. GUDENTITE!
Can I use the stock 14s on my 900 xp rzr there 1+5 front and rear and how much total width gain per side?
I don't think stock tires will still work with portals
Also running a 32 how much top speed will I lose of I go with the 30 percent gear reduction vs the 15 ?? I already have some clutxh work done do u think a 15 gear reduction would be enough with my clutch work or 30 be better?
I think there is no point in doing the 15, upgrade to some 34-35s and do the 30% and youll be happy
Hello guys - i can not make caster on rear axle on my rzr xpr 2 seats- i try all shims but they all make wheel look outside - All suspension standard. What it can be
Should be able to adjust your radius rods
Awesome video... will fit macerick x3 xrs turbo , too ?
They make them for X3s I believe
Do you think these portals could handle hitting jumps and racing or are these just for rock crawling and mud?
With some mods they might hold up to racing and jumps. It is just a lot of leverage
If you measure the toe-in while the suspension is hanging won't that measurement change when the vehicle is back on the ground? Of all the vehicles I've worked on the toe-in is always measured with the weight of the vehicle on the suspension.
yes
did u use a wood hammer with a claw to remove the spindle lol hahhaha that's awesome
gotta do what you gotta do!
Come in handy
no doubt
I would love to see a video of this beast in action! I'm curious if it will hold up to the hill killing abuse that the other buggies go through. Any footage of this coming?
Yes we have a full trail riding video coming soon where it gets put to the test
BustedKnuckleVideo awesome! I look forward to it!
What brand 30mm did you buy for the Castle nut, you said Lowes so I'm assuming kobalt? I have 2 out of 4 portals leaking so tomorrow night starts the breakdown and redoing the seals.
not sure on the brand, shouldn't make a difference
@@BustedKnuckleVideo thanks
when you say gear reduction does that make your rzr slower?
If you run the stock size tires yes, If you put 34-35s on it then no.
Super atv needs to make these portals for a Renli 1500 UTV.
for a what?
someone buy that boy a real hammer lol..great video guys
We have a Thor Hammer now!
@@BustedKnuckleVideo the claw hammer just wasnt right lol
not at all
A (( Renli )) 1500 cc 1.5 Liter 4 cylinder motor. 108 HP 125 Ft-lbs torque at 3,000 rpms. Just look them up and see for yourself.
not enough power
Love the cage, what company can I call to get one? Thanks
Rocky Hollow Metal Fab
What size roctanes did you put on there?
34s
The only problem i see is you would get the 30% reduction while in HIGH also
true but we have the larger tires so it somewhat evens out
What happened to part 2 of this video?
Is it out yet.
He is shooting it next weekend we hope
Right On, can't wait to see it. Thanks!
Got nice place myself not as big
nice
Класс! Покатушки
👊
What is the weight of that tire and wheel combo?
A Lot! lol
How wider will these make the rzr?
its probably 4" wider on each side
If I buy a set, what would you charge to put them on since you have already done it? I live locally
Locally to where? Rocky Hollow?
Close to Gadsden, I stay in Calhoun county
Rocky Hollow might would do it, we are moving into a new shop in Cullman.
Ok thanks
👍
you should use amsoil
why?
What a arms are on this rig?
ORB Fabrication
What ever happened to the k 5
it is still in the works, gotta go pick the new motor and trans for it up this week
I'd love a set but man are they pricey. ...... Not sponsored by Pittsburg tool. Lol
We need a tool sponsor for sure!
You put your hub and rotor on the wrong side and also put oil on those blue gaskets prior to install.
hub and rotor on the wrong side?
yeah rotor on backwards, slots face back not forward
Have lifts
yeah we gotta get one or two
Нету таких грамотных, а вы кто? Вообще и в частности
Я Busted Knuckle, оператор и гонщик.
Перевод на русском языке есть?
еще нет, если вы не знаете кого-то, кто может перевести с английского?
😴
Portals for the win
If you're going to make a video, do it somewhere there is not hammering.
This is like a snuff film. Low budget
it was the only shop we had access to at the time so get over it
@@BustedKnuckleVideo If going to be that bad ,dont upload the video .
Go back to video school and learn how.
Get a real mechanics hammer, your not driving nails !
We use what we got. No professional mechanics here.