Royal Enfield CAST IRON STD 350/500 carburetor setting(English)
Vložit
- čas přidán 4. 07. 2024
- This video we have made for educational purpose. We may be wrong. One can make own decision for repairing. We are not responsible for any damage or risk. Thanks and stay connected.
- Auta a dopravní prostředky
I always do tuning myself on all my vehicles, I teach and explain people . But I could never explain aux screw influence in tuning to other guys. You did it so well !!. I see many mechs just keep the aux closed as they are not sure what to do with it .
Thanks for the information 😊👍👍..... I've just tuned my CI 350 as you taught.... and noticed that, the blasting effect which used to come earlier while throttling up the engine ...has gone!
Thank you 👍👍
Glad it helped
Have taken this bike on your ? Your code engine bullet ?? How was your experience so far ? Can you also use this as your daily driver ?
Very very very good video brother. Nicely explained everything thing, it's a full training videos,
Thanks a million for sharing. Best video I watched on CZcams ever till now.🙏
Nice video sir i did my setting on my 99 and66 bullet very well explained thanks
Hello boss.. Finally I got you.. Have been reading about you for a very long time.. Wanted to talk to you.. Thanks boss
Awesome bhai.,,still remember when we did this on my vehicle
thanks for the update on carborator setting, it was helpful, keep updating maintanace for bullet 350 cast iron ingine.
How about the starting in morning .chock needed ??
Is it necessary to open the primary air screw..can we lock outer air permanently???
Many thanks Chinmoy Sir...👍👍
you are welcome
Fantastic video!
Do you have a video for older CI engines, 1971, which has VM carb but only 2 set points, the idle screw and the AF screw? No resonator/auxillary screw.
Hi Chinmay, I have Bullet CI 1980 model CB point /12 volt with three phase coil output….can I use 55/60 w bulb in place of 35/35 wt. ?
Its Really informative and good work man...
Thank you for appreciating
@@MechAutoClinic Hai brother can you please mention which grade oil is best in old ci engine(royal Enfield std 350 petrol) waiting for the reply
Hello Sir. I didn't quite understood the auxiliary screw setting. Is it like that the screw needs to be adjusted at a point where RPM of the engine starts increasing?
yes but depends on. it should come to such point that counter clock or clockwise RPM should drop. if the point is perfect then RPM will be high. thanks
Hi Sir
Is this settings okay for Mikuni Japan make carb for Bullet. Is this carb have air screw with a spring in between.
No other air screw look alike found
yes common for VM24/28.thank you very much for appreciation
सर आपका विडियो बहुत अच्छा है पर कृपया कर इसे हिन्दी में बनाए क्योंकि पुरानी बुलटो में माइलेज की बहुत परेशानी होती है
Definitely sir i too mean that
sir at the time of tunning the carburetor we use new sparkplug or go with old one plz tell
Go with new plug so that later we can understand tuning is perfect or not .
Sir, I have Suzuki Heat 125 which has a Mikuni VM18 carburator, may I keep AFR at same 1.2-2 turns? For your info, the AFR screw is at the intake side of the head.
VM Yes.
Sir can u please tell me about putting mikuni carburetor for my old bullet 500 cc
There is a miss fire in air filter side old bullet . Some times it's miss fire while starting the bike. Can u help ?
Thanks for sharing this amazing knowledge.
My pleasure!
thanks sir and nice video
Hlo broo nice and awesome video 👍
Sir, I have Bullet 350 2006 model. I was doing carborator tuning as did you.
But was not going like you, rpm getting high and stoping during rpm goes down.
What i did as below.
1. Increase rpm without meter
2. Closed auxiliary bolt (tight clock wise mean left to right)
3. Closed air mixture bolt as clockwise.
4. Open air mixture bolt 1.5 to 2 times, rotate right to left side.
5. After that open auxiliary bolt around 3 times.
But rpm not getting down slow as CI bullets have and either no water coming from silencer 🤔😥.
Please advise🤗
2
Thank you very much for sharing this video
Sir,
Thanks for this video.... I am working as a mechanic in Kerala... I don't know the use off emission screw.... Ur video so much helped for me..... Plz make engine resetting video and 5 speed gearbox working resetting video too
My Enfield model 1993.... Is it same for this?
Ok
@@MechAutoClinic sir this tuning same for my model
@&%#####&
Mani ashan 🤔 oo bullet mani
Ayal thallu mesri aanu Keralathil paniyariyunbavar kuravanu ngan Chinmay bro yude yella vedio yum kanarundu he is A perfect mechanic also brilliant, he is having excellent idea's
Thanks a lot to chinmayji
Is that engine chrome plated or buffed, please reply. Can you suggest a way to get my bullet engine mirror like shine permanently.
yes, it is chromed. you can do except main engine case. Gear box cover, clutch cover, timing cover you can chrome. Main engine case chrome will five you heating issue, aluminum only exchage the heat well n good
Sir, I have Suzuki Heat 125 Four Stroke, 2006. It houses a Mikuni VM 18 carburettor. Will the setting go same for my bike so far as AFR screw is concerned i.e, 1.5-2 turns? I am eagerly waiting for your response. Thank you! By the way I have set it at two turns and motorcycle even starts without choke and good crisp acceleration. The spark plug colour is like chocolate brown. At electrode it is brown and the thread circumference is black in colour. Please clarify.
bike starting without choke means mixture is wrong...its rich,. make it lean.
Hi can I tune my carb without touching auxiliary air screw (tuning with pilot and idling screw?)
warm the bike followed by open the carb slide for 1/4 portion by adjusting the idle screw. Now adjust the air screw for max rpm. Finally set idle screw for your desired RpM. tuning is done now.
sir hats off to you
Thanku so much sir,,,
That ws much much importnt 4 me..
Thanks for waiting so long...and sorry tk keep u waiting..its all depends on which vehicle we get...since i have stopped working on these bikes from 2015...so its rakes some time...i hope u like it... thanks for connected.
इस वीडियो का हिंदी अनुवाद करें आदरणीय आपका नंबर नहीं मिल रहा हमको गाड़ी भी स्टेशन कराना है आपसे मैं बहुत प्रभावित हूं
Very well informed
Superb sir jii❤️❤️
Sir,,,,is it same with electra c.i.2009 model?????
Hello sir at 12.30 how did you set the auxillary.You had mentioned rpm should be max and will be low if we rotate either side. Kindly clarify
Ya he done it so fastly
just open the aux screw slowly the RPM will increase at one point the RPM will reduce. The maximum RPM is correct set. simply said remember a mountain....slop mountain peak again slop
what is the part called taht is between the engin and carbarator( with the yellowish pipe). my bike does not have that
But I have 1967 ci
If bike don't have auxiliary unit then what is air mixture turns setting,my bike is 1962 model how I set it I replace my carburettor but it don't work
Boss in my ci 350 bullet .mechanic has tunned the mixture and speed knob.he completely tighten the outer air supply .
Is it fine to go with that???
I dont think..its not the proper way to tune
Same mere mechanic ne b liya hai 2007 electra model me
This tuning is suitable for 350 fitted with miccarbs also, right sir
Yes. All VM series.
Hi sir, I own 2009 electra 5 speed. While tuning using Aux air screw, rmp drops very slowly but idle rmp is stable. When aux air screw is fuly closed and carb is tuned, engine rmp drops immediately when accelerator is released. Any inputs.
Any updates? I too have the same issue
Sir,I don't have the auxiliary screw for air,I just have two settings in my old ci engine 500cc bullet carburettor can I also go with the same settings as you have shown, superbly explained.♥🙏
That's ok. If not having then just tune with two points
What a stroke after tuning, it is the bullet's firing I love much more!
पुरानी ३५० झिंदाबाद!
enjoy
Hii I like to know about silencers that are suitable for G2 engine
mine is 2008 model, which carburettor it has, and mine is giving 20-22 kmpl is it ok or any measure to improve this?
It's very low dear. My same model bike get 44-45 km/ltr.
You should maintain that bike well to get more mileage.
Better engine oil-gear oil- clutch oil, clean air filter, lubricated chain, properly inflated tyres... Then the last one 'tune the carburator'..
You did wonderful job with bike its buffing and nickle work is very much appreciative, my senior's royal Enfield mechanismo is in workshop for whole work and modification of engine with old model bullet & heavy Crank but i am not satisfied with buffing, nickle and paint job, i hope he will do nice work on engine, i daily visit workshop for updates , hope i could get chance to visit your workshop, i live in uttar pradesh..
Always welcome to my shop.
@@MechAutoClinic : sir its more then shop for me i am crazy about this motorcycle , how can i contact your workshop for a visit or for motorcycle...
@@MechAutoClinic : sir want to ask from you can you please make video on timing and point settings on old royal Enfield.?
@@crazynmad89 ok
@@crazynmad89 macasp@gmail.com send me u r details there
I will share mine over there only
Sir my bullet does not goes beyond 40kmph is that due to carborator
All engine work is done about 6 months before
awesome
Hi, is there any way I can come to your garage regarding my bullet electra? I stay in Thane, Maharashtra.
My bullet jerk after changing 3rd to 4gear what is cause of it ?
That's so nice a video... The best part was you told how to validate the settings... Thank you very much Chinmay ji💐💐💐
thanks for appreciation
Easy reference all time
Sir in my bullet 350 1989 model there is black sticky material forms in the carburetor. Even after cleaning it comes back within 3 to 4 days. do you know what might be the reason?
OLD FUEL ...BASICALLY FUEL BY PRODUCT IS VARNISH. SO IT IS A STICKY SUBSTANCE. MAKE SURE YOU USE NEW FUEL ALWAYS AND DON'T KEEP FUEL IN THE TANK FOR LONG TIME. ALSO MAKE SURE CARB PACKING IS NOT LEAKY...THANKS
Thank u
The rpm is not constant , in my 83 model 350 its slightly raised after 8,10 km ride
Looking at your video....it appears like the choke was ON.....but tuning is always done with choke in off condition.
Hi bro nice sound pls tell me exhaust name I want to buy same one
Thanks sir. Well explained
Sir i’ve a suzuki samurai. And what problem im facing is bike only runs on half turn out from fully seated on afr screw. Even on half turn bike misfures at lower rpms. Factory recommended is 1.40 turns out but when set the screw to 1.40 it is getting lean. Even it is on 1 turn it is running lean. I’ve not found any solution for this kind of problem. Recently it got rebored. Previously bike runs on 2 turns doesnt faced any kind of problem. After rebore im facing this. Intake manifold flange was new, carburetor o rings are new. Spark plug, cdi, ignition coil are new. Please help sir.
Check the carb and clean it thoroughly. And AFR setting for any two stroke is 1.5 to 2 turns.
Hello, chinamy. Can you please tell me the model number for VM carburetor. I found a new one in Amazon. I am very unsure whether that suits.
Thanks
Hi, My bullet 500cc got vm28 carbe. Can I do the same settings for that
Thanks
yes
Thank you really your explanation was usefull for the settings,And I have a doubt we just rebored my old model Bullet 1984 Which is G2 Engine but It was having Starting problem so i just showed to a new mechanic he says that the Top Bore doesn't have good Compression and he is asking to change it.What to do because I didn't even drive 2000 km after reboring.so if you have a good idea kindly suggest me
what is the compression on the gauge?
@@MechAutoClinic I don't have any seperate gauge for the compression
Sir I am getting maximum rpm in 4half turn but pick up is average if I come 2.3 half turn pick up is good mileage will get less so which is the correct position sir
as per the video I go. thanks.
thank you.this video is so much educative
you are welcome. thanks for appreciating.
Axjaly skru kitna churi kholna hai please bataye
Bast video sir
Jai bharat
thank you very much for appreciation
Where is ur workshop located sir ????
What should be the float height in VM 24 carburettor
i will let u know via video if it is ok with u...so every one will get to know about it. thanks
28 to 30 mm
Bhai agar koi old 500 CC hai to btao i want to buy.
What I do for it
What If There Is No Auxiliary Nut ?
Old model ci engine HOW TO ADJUST TAPPED PLEASE EXPLAIN
❤
Air scrow bike start krke hi set kiya jata h or wo bhi gadi ki engine ki setting ke mutabik yani new engine bna h uska alag hota h or jo chal chuka hota h uska alag hota h..gadi ke sound ke hisab se hi air set ki jati naki bnd krke
Good sir ji
thanks
Sir jii aapki shop kha hai..
Sir Jab maine apne 2007 electra with turbo jo mere mechanic ne band liya hua hai k corburater observer ko two time pe khola to rpm kam ho gya throttle bdaya ik dam rece bada aur phir kam huya aur band ho gya jab maine clock wise ghuma k band kiya to rpm aur engine ka slow theek ho gya sir ye ulta ho gya apki video se iske solution btaye
Hello Chinmay Sir..
How are you? the video was really full of useful knowledge.
Sir..I have an old bullet with CI engine. the problem I'm facing is that when I need to stop at traffic signal or somewhere else I have to keep brake paddle pressed if I release brakes the bike starts moving without releasing clucth lever and if I tighten the cluctch to fix the problem the kick lever starts slipping. sometimes the engine switches off itself when I stop. What should be the remedy in this situation.
clutch center nut loose or clutch setting is not good or clutch plates and frictions plates are gone. thanks
@@MechAutoClinic thanks a lot Sir.
point seting video bhi bano bhai
Sir while opening auxiliary screw rpm is not much increasing as your bike , firstly it increases and while more opening it lower down . Pls tell the problem in bike model 2010 only 5500 kms driven . No other problem in motorcycle but i want to tune my motorcycle as yours having water droplets in silencer . Your tuning is perfect 👍🏻👍🏻
change in RPM due to AUX is defer. it is bike to bike. not all will have same setting. so I dont think it is wrong in your bike.
After seeing ur video sir i tune my carburator after that i get water droplets in silencer but i can't get slow ideling like u my idel screw get out fully .what mistake i made sir? Plz reply
you made a mistake...just re fix the screw and set the idle. it will be ok
@@MechAutoClinic thanks a lot sir for reply you r great person too...
@@MechAutoClinic sir my bike electra ci 5speed is without auxiliary been removed by previous owner I've tuned it by one half turn 1.5 of the air screw starting the bike is also difficult,and when it eventually starts it sometime develops hiccups and stops.what could be the problem
Hello sir, can we install carburettor flange as in this bike on my 1966 350cc enfield for better mileage
you can ...but then you must have carb which is compatible with flange
@@MechAutoClinic yes sir, I have vm-24 carb and also the air filter box has that air flow nozzle in it. Have got it fitted last Sunday and it's running fine 🙏
sir i am having electra cast iron bullet 2007 model
plz help me tune carburetor with auxilary screw
Brother! My bike has no auxiliary screw, it has starting chowke,,, ideal screw and air screw.... ! I set it as you mentioned in video,,, 1.5 (3 time) but one problem I'm facing while starting my bullet 350,,,, that I it is must that I pull the chowke! This is 1986 mfd bike,,, but carburetor is new one.
Yes,
My 350 is the same as yours!
Set it 1.10 to 1.15
Timing gear tappet must be free to move . Check them when piston on top . Also adjust carburettor piston needle on second from top. 1.5 or 2 turn not recommended for all bike ot totally depends on the condition of your bike health like intake valves / head compression.
Hlooo Chinmay bro how are you love you miss you those days nice informative video dear bro and where is your mustache gone nice look dear bro when will I reach u bro miss u bro take care 🥰🥰🥰
sir where is your service centre
Hi bro! I've 1996 ELECTRA and I need VM24 carburetor and air filter for my ride. Can I get it from you?
Sorry for late reply. Yes you can get it but unfortunately we all are in lockdown so I can't help you in shipping.
@@MechAutoClinic bai ji need ur contact number
You belong to which state
Sir please help me , when i start my bike it sounds too loud and after riding a little my bike gets off and my carburators screw doesn’t work which u used to decrease the thump , so please help sir
what bike you are running? what carb you have? what tuning u have applied? thanks
Mech Auto Clinic sir i am having royal enfield old model and it is loaded with micarb carburator and I don’t know about tuning sir
same like what showed. only u may not be having AUX screw which you can ignore. thanks
timing setting ka video nanalo(timing wheel position and piston position ,point opening point,)
How do you measuring bloody rpm?
Possible yes
Hello sir,
Please tell us how to tune the carburetor on Bullet standard 500 uce.
will post up video soon. thanks
@@MechAutoClinic Thanks 🙏🏻
Chinmay sir please help me meri bullet ka tune up karna hai
Hi Sir i liked your video but my ci engine bullet has micarb carburator and as per video i have open fuel to 1.5 round and slow down the rpm. Then i have slowly open the auxiliary screw but it doesn't affect the rpm. Please suggest something to set accurate petrol mixture
Make sure aux vent is clean
@@MechAutoClinichow to set mixture without aux vent .in micarb carburator . Is best mixture is when the rpm is high
Sir mere 2001 model bullet ka main engine oil drain nut sleep ho gya haa kyaa kru....
repairing ka video upload kiya hain please check the video list. thanks
@@MechAutoClinic sir i am already see your all videos sir...that video on uce engine not for CI...
My old bike has two settings, can guide me abt that. Thank you
please explain 2 matlab kaunsi setting
@@MechAutoClinic my bike model in 1978, and carb is vm 24, in your video you shown, 3 settings in the carb.
But in my carb, i dont find any auxiliary setting in it.
So its basically only 2 settings found in it, (the bigger screw for idling and another smaller one), how do i tune this carb? Can you help me with it sir.
@@vinanthsp815 just turn AFR screw to 1.5 from full close position thats all...
Hi sir,
I own a 85 DELUXE model enfield. Mine doesnot have auxiliary air intake... So could you show how to TUNE the carburator in such bikes..
Same way ...just forget aux if u dont have...
Just fix the airscrew in 1.75 position.
That means 3half turn and a quarter.
How to point set sir please
I have the same engine and my mechanic has kept the aux screw to fully closed position.... He always adjusts the air/fuel screw and the idle screw.... I have always had starting problem in cold weather... Summer is still Ok... Please help
you can try as i have shown in the video. may help you. thanks
you can try as i have shown in the video. may help you. thanks
@@MechAutoClinic I dont have that special tool to help in the tuning
I am having 1978 what would be the carburetor type?
VM
चिन्मय सर असाच विडिओ 350 क्लासिक साठी बनवावा । आभारी आहोत।
Ho he sagle june videos upload karne chalu ahe...ekda english sample ki mag karto ...te sudha marathi tun