Video není dostupné.
Omlouváme se.
How to Replace Front Lower Control Arm 08-14 Cadillac CTS
Vložit
- čas přidán 29. 09. 2019
- Buy Now!
New Control Arm with Ball Joint from 1AAuto.com 1aau.to/ia/1ASL...
Control arms are a crucial part of the suspension system of your vehicle. They not only carry the load of the vehicle to the wheel, but they typically also maintain its alignment. Control arms are typically large and strong, so you may be surprised it needs replacing. They contain rubber bushings for smoother rides at the cost of eventual wear, as well as integral ball joints that also wear. This video shows you how to install a new quality TRQ lower control arm in your 08-14 Cadillac CTS. The procedure is the same on either side of the vehicle.
• Check here for more videos on the 2008-13 Cadillac CTS: • Cadillac CTS 2008-2013...
This process should be similar on the following vehicles:
2008 Cadillac CTS
2009 Cadillac CTS
2010 Cadillac CTS
2011 Cadillac CTS
2012 Cadillac CTS
2013 Cadillac CTS
2014 Cadillac CTS
2015 Cadillac CTS
Tools you will need:
• Pry Bar 1aau.to/oa/1AXA...
• 18mm Wrench
• 21mm wrench
• 21mm Socket 1aau.to/oa/1AXA...
• 22mm Socket 1aau.to/oa/1AXA...
• 24mm Socket
• Pickle Fork
• 1/2 Inch Air Impact Gun 1aau.to/oa/1AXA...
• 1/2 Inch Breaker Bar 1aau.to/oa/1AXA...
• Ratchet 1aau.to/oa/1AXA...
• Torque Wrench 1aau.to/oa/1AXA...
• Anti-Seize Grease
• Block of Wood
• Marker / Writing Utensil
• 6mm Hex Socket
• Center Punch 1aau.to/oa/1AXA...
• Floor Jack 1aau.to/oa/1AXA...
• Hammer 1aau.to/oa/1AXA...
• Rubber Mallet 1aau.to/oa/1AXA...
Subscribe: / @trq
Check out our playlist:
Cadillac CTS 2008-2013 Second Gen: • Cadillac CTS 2008-2013...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
Thanks for taking the time to show the in-depth process of this. Now I can decide if I am going to tackle this. Doesn't look too bad but the car I would be doing this on will not be on a hoist so the job will be a little tougher.
Beautiful instructive video
So you droppen in the ball joint and shock into place with out a press tool?
Can you separate the outer tie rod to move the inner tie rod out of the way enough to take the CAB bolt out and can you put the bolts back in backwards so the bolts come out from the inside of CA?
that looks like a different process from my CTS. Mine is a RWD with aluminum subframe.
How to replace the thermostat on my 2006 Cadillac CTS 2006
What is considered ride height?
If I go with aftermarket polyurethane floating bushings, is torquing at ride height still necessary?
How about the drivers side rear control arm? Anyone seen a video or have knowledge on it?
How much would this cost? On average?
Shop i was quoted 1.6k.
Not a caddi dealership either.
Cant replace just the bushings? Or need to replace the whole arm
Do the entire arm while you at.it I needed just the bushings it was just as much as doing the entire arm. you can do just the bushings though
The rears have them availible.
@@shortdom107 it's a lot cheaper to do the bushings, right?
I seen bushings for less than 100, while the control arms are 300 ish each side
Do bad lower control arms cause the car to shake
Yes. Have someone you trust sit in the car and with it in reverse, look under the front as the driver moves the car backward a couple inches then steps hard on the brake. Don't let you wife do this if you expect she might want to collect your life insurance if she "accidently" puts the car in drive. Watch the forward bushing area of the lower control arm. If it is good, the only motion will be "rotary" around the bolt as the arm moves up and down. With the bushing bad, the bushing area of the arm will move noticeably left and right and/or up and down. Remember, the ONLY motion of that part of the arm should be from the bushing twisting one way or the other around the mounting bolt as the arm moves up and down.
Yes it will and the wear on your tires will be uneven. It's another expensive issue with the cts 🤦🏽♂️ it's such a beautiful car but damn they have sooooo many issues
This is an awd one right does not.look the same as my red ones
Correct I have RWD and the LCA are slightly different