How To Guide - Pairing Your DumboRC x6 Transmitter to the X6FG Receiver
Vložit
- čas přidán 9. 07. 2024
- In this video, I show you how to pair a DumboRC x6 Transmitter to the DumboRC X6FG receiver.
Our store: teamjbhobbies.com
Get the Transmitter and Receiver here: teamjbhobbies.com/products/du...
Come join us in our Facebook group. A place for all things hobby related!
/ 343879173657374
Follow Us:
/ teamjbhobbies
/ teamjbhobbies
/ teamjbhobbies - Jak na to + styl
Absolute life saver for telling me about the black wire to the right!
If only the chinstructions showed you how to put the wires into the receiver! THANK YOU! I was close to packing this whole thing up and sending it back!
Same here!! 🤣
I'm new to rc and I couldn't believe how vague the instructions are with everything.
I'm building a Tamiya kit, which has very detailed instructions on how to build it, but when it comes to the electronics everything is vague. Apart from the warnings about connecting things the wrong way and the damage it could cause. 😡
Just got this and I’ve been searching all day for a video like this!
Simple and to the point. Thanks brotha! 🤘🏼
Thanks for the video!
This is a great video 💪🏽🇬🇧👍🏽
Great job cham
Very helpful thank you.
Thanks i’m a beginner to the rc world and just bought this.
Wow didn't know it's so easy great video bro. I'm using my Dumbo x6 on my outcast 8S exb. I keep cutting the receiver wire even with destroyer in place any recommendations
Thanks it worked
Thank you, for a concise, clean and on the mark video.
I'm surprised how little info I can find on this RC receiver.
No problem. Hope it helped!
perfectly explained video, for that i thank you.
Thank you for the informative video. Do you also know how to setup the fail-safe in case the transmitter gets switched off?? Thanks in advance.
Would love to know how to do that as well. Got one receiver that works ok, the other does the thing when i turn the receiver off, engine starts to run. Thats frustraiting
After 2 years or so my receiver wasn't responding, pressing the button reset the thing from Orange to Green Orange being gyro on green is off. But now the button doesn't even want to do any thing any thoughts or pointers? Everything was working great until, well that's just it nothing happened it was out of nowhere
Hello, just an outside question. Does increasing the voltage of the remote help with better signal and range?
hi mate! do you know why my dumbo remote operate in reverse for steering and throttle when i'm finished binding.already tried for few times result still same.switch also have been set to normal.
Flip bro Thanks for sharing this about the dumbo rc
No problem! This is one of the most common questions we get about it.
@@teamjbhobbies 100% bro thanks again
Thank you
Bro. I been trying to figure out why nothing works. Once you said black wire in right. It worked. That was my first question since this is my first RC. We are not dumb dumbs. But orientation matters. The more spins forward or back that’s just swapping motor wires.
can you show a video how to setup the Ariel for the receiver. i have no clue what to do to have it neat. thanks
I would think that is very dependent on which car you are installing it into. Mine has a tube where it runs through. I think I would just run the wire how your original receiver had it.
Does it pair with other brand receivers?
I just bought transmitter x6 and x6f receiver. Can i change from old x6f to x6fg gyro receiver with same x6 transmitter ?
Yes you can!
Hello, you explained the video well for a starter like myself.
But I have a question, I bought this transmitter. But my car has an ESC/RECEIVER combo (HBX 16889). So I need to purchase a separate esc. But on the website it also says you need some kind of program card??? Do I still need that if I got this transmitter? Sorry for long question.
A programming card is something you can plug your ESC into to set up the settings. With a lot of ESCs, you can set up the settings without using one by listening to beeps and pressing buttons. Each ESC brand would have its own programming card you could purchase separately if needed.
I think it might be a challenge fitting an ESC and the Dumbo X6FG receiver on a 1/16th scale car, but I would love to see it if you do make it work. Let me know!
@@teamjbhobbies thanks for reply. But can I purchase any brand esc and any random program card?
Some shops on AliExpress only have the esc with motor, and others have the card that go with it
Sorry am still new to all of this so I don't have a clue what to do. And with this lockdown, all I can do is get help from youtubers!
@@doylecholesterole1927 Your ESC would need to match the type of motor you have. If you have a brushless motor then you would want an esc for brushless (vs brushed). I would suspect your car came with a brushed motor but you would have to check your manual. A quick search on amazon for "esc brushed 1/16" brings up some options. The program card would need to work with the esc you buy. So if you are going Aliexpress you never know what exactly you will get vs if you went with a name brand you know they would work together.
Then again if you buy an esc that you can program without a card that is fine too. And you may not even need to program it at all if you just want the basic settings.
@@teamjbhobbies @Team JB Hobbies okies, thanks for the tips. The HBX are brushless. I'll try without the card first. I can always wait if I do need it. But that ka again
Do you know any videos that show this radio and receiver in a nitro rc?? Trying to figure out church channel the battery goes In and the glitch buster
Hi, I did a little searching around and I think you have to have a different receiver to use this radio with a nitro car. I found the DumboRC X6YCG receiver is advertised for Nitro but I am not 100% sure how it differs or how to wire that. Sorry I could not be of more help.
Can I use this dumbo transmitter with my stock servo or you have to change the servo too? I have a typhon 6s
You do not need to change the servo. You will just replace the receiver.
@@teamjbhobbies Thanks
hi, but how on your controller is a blue light, on mine it blink blue and white, I don't understand and when it blink like that only the wheels on my car work, does it mean that the engine is dead, the engine is brushless or, if you can say something about it,thank you👍
If your transmitter light is blinking you could need to just replace the batteries. Try a fresh set of good-quality batteries and see if that resolves it.
@@teamjbhobbies ok, thanks, I have new batteries, I'll try them and write how things are, thanks again
@@teamjbhobbies new batteries but still the wheels don't turn, I think the engine is dead, I don't think there is another explanation.
❤❤❤❤❤
what does the light mean if it turns green ?
Green means that it is normal mode (non-gyro). Press the button 3 times to make it gyro mode.
Mine will bind the receiver won't blink no matter how long I hold the button
1 turn
2 burn
Is how I remember lol
Whats the gyro? Do I need it on or off? Great video
A gyro receiver stops the RC car from spinning by making adjustments to its steering so it can move in the direction you want it to. The more throttle you give, the greater the disbalance between the front and rear of the car; the gyro receiver counter steers the RC car.
The gyro receiver keeps the RC car’s tires aligned in the direction you choose; regardless of the track traction and external force, the gyro precisely maintains the direction you set the car to move in.
Basically, if you are about to spin out from a sharp turn or gunning it in rough terrain the gyro adjusts the steering for you to keep you going straight. I personally turn it on and just the channel 6 knob to adjust its intensity. You can set it to 0% on the knob to disable it (practicing for a race maybe). Or set it higher if you are just having fun and want to gun it without worrying about it. Just a quick note if you set the gyro too high you might see odd behavior like twitching.
@@teamjbhobbies ahhh ok thank you so much for your quick reply
2:00
Which X6 transmitter is this? None of the Dumbo X6 I see around has this red painting
The strangest thing. The red version is no longer produced. The supplier told me that China made a new rule and red was no longer allowed (this was quite awhile ago at this point).
@@borderjs all right then, nothing we can do. Thanks for the repy!
1 to turn and 2 to burn
I just installed this system and the receiver binding button just fell right off. I simply tried pressing it in with some tweezers and it fell right off, barely any pressure. I could feel the button click right before it broke off, so the amount of pressure to simply press in the button, was enough to break the switch right off. Well, another ones on the way. At only $18, why not try again. Sure am hoping the next one isn't a total piece of garbage. Get what you pay for, I guess🤷🙄
your steering servo is very slow :o
Which servo do you like to use? This is just a random basher to demonstrate pairing. :)
Again the receiver needs a label or one way plugs 🔌
What is that car
This is an Arrma Granite 3s BLX
@@teamjbhobbies those are nice tires