Vacuum Engine Mount / Motor Mount Replacement
Vložit
- čas přidán 29. 12. 2015
- Donations www.paypal.me/SiRobb/
www.amazon.co.uk/shop/sirobb
As an Amazon Associate I earn from qualifying purchases. Using my Amazon links does not cost you any extra. - Auta a dopravní prostředky
I cant see my rear mount in my car but ill look again! But must say when it comes to helping people out on youtube i have to say its the best ive seen by far!!! Well done mate.. your gona help so many guys out!!
Thank you SiRobb, your channel is definitely a treasure for Volvo owners.
Yep so easy to follow.
Miss him doing new videos with new tips and tricks… but well, maybe we’ll see him again one day. Until then tolly/IAMASPANNER is also a great resource for D5 owners
Thanks SiRobb, i've just changed them, your channel helped a lot!
The video is a bit old but you just saved me a lot of hassle. Thank you for this awesome demonstration.
SiRobb, great videos on the S60 D5!
I had issues with the car loosing power (going in to limp mode) contacted Volvo dealer but as usual they told me it could be hundreds of potential issues (but they would be happy to diagnose it for large pot of gold). Searched you tube and found your vids, so bought a vacuum tester and found front engine mount loosing vac, replaced following your vid and all fixed, also found the lower gearbox torque mount shot (now fixed with inner tube).
Keep them coming, they are very clear and straight to the point - well done and thank you.
How did you diagnose the vacuum, I am having the same problem with a Volvo xc90 2008 Diesel, I also have the poping noise coming from the engine when you remove the oil cap from the engine. I am not sure how to diagnose if my problem is my motor mount or my vacuum pump.
i can only add one advice - do not thight the bolts up right after installation. First start the engine and let it work for some time to sit in proper way. Than turn of the engine and thight them up.
Good Job SiRobb :) TY for sharing.
Yes that's good extra advice.
@@sirobb hola sirobb , esta es la solución para el ruido de estallido?
Great video, thank you very much. Based on this video I've done myself the fengine mount change. Based on your other video (with the vacuum leaking - noise from the engine), also managed to diagnose the wrong engine mount. Thank you again, you are a real Volvo expert!
I could have done with this video when I changed the front & rear vacuum mounts on our D5 XC90 last Summer. The VNT ring on the turbo was knackered so I changed that too. What a b*****d of a job that was trying to fit the oil return pipe to the turbo & into the top of the oil sump. Great video! Reminds me of that weekend I spent lying on the driveway trying to figure it all out.
Thank you for the video! I changed mine today on a 06 XC70. There was very little clearance around the sway bar. I used a crowbar to get the socket in to remove the mount, to install it I used a long 1/4" drive extension and socket, using tape to secure the bolt to it. That worked like charm, then I tightened it with a 3/8" drive socket and extension. The front mount was definitely the hardest to remove and get out past the cooling fan. No vacuum connection on my mounts, thankfully!
Changing the two large mounts and the side mount by the main pulley definitely helped. There seems to be better isolation from engine vibration and it makes the shifts feel better.
Thanks Si. Just replaced both of mine with Corteco mounts, 110k V70 2005. After renewing the bottom transmission link the engine really vibrated bad at idling. Rear mount not holding any vacuum, front mount leaking slowly. My engine did not go up as easy as yours, started to lift the car ! Had to loosen the rear mount to allow the engine to tilt to release the front mount. Rear mount came out very easy because it had partially collapsed, had to raise the engine another 10mm to get the new one in, bringing the exhaust shield hard up against the brake vacuum unit. The right angle plastic vacuum connector was seized in the rear mount, had to spray with a silicon spray and work it with pliers to release. The new rear mount was a pig to align, had to wedge it in place and lower the engine 2mm at a time to ensure the bolt and vacuum port cleared the bracket holes. Great video thanks, would not have done this without it. 🥇
Update, also renewed the top mount at the same time. First engine start no noticeable difference with vibration through to the steering wheel!
But after the next 200 miles the mounts have now settled and the engine is back to normal vibrations. When the engine returns to idle and vacuum is applied to soften the mounts, reduction in vibration is noticeable.
You forgot to mention you need to replace the lower gear box torque mount as well. Super video though - thanks a zillion. Love your videos - makes it so much easier to run an older Volvo! You're the Man!..:)
Thanks for the tips, great video......Thank you SiRobb
Absolutely brilliant, mate! Thank you so much for taking the time to make and post this!
perfect as always, SiRobb!!
This was so handy. Go to do all 5 of mine next weekend. Thank you
Superb video Simon - even if I can't do it myself it is still incredibly helpful knowing what and how! Thank You!
Thank you so much for the video. Gave me the confidence to replace the leaking mounts on my 06 D5 You are a legend 😎👍
Excellent video. Thanks for taking the time to put it together and for uploading :-)
Class. Just showed me how to rectify my limp mode problem. Changed both mounts and turbos working fine. Been to three garages and spent thousands. New egr valve ect and they couldn’t find the problem. One look on here job done. Keep up the good work. Respect due.
What kind of problem did this cause your car if you can recall I know the comment old
awesome videos bud, think I've gotta say my V70 D5 has gotta be one of the best cars to work on and service
Thanks for the video, it was very helpfull. My only problem was that I couldn't reach the bottom bolt with my 1/2" wrench extension, it was to narrow. So I had to buy a 1/4 "" 14 mm socket. and an 1/4 " extension. Once I had those, it was a piece of cake.
Greetings from Holland (sorry for my bad English...)
amazing set of videos this guy is what you call an expert knows what he is talking about keep up the good work love them
Thank you very much for this video. I'm going to watch it a number of times before I change them over. Thanks again👍👍👍👍👍👍
Just done mine 100% great video only problem I had was rear space was hard with the prop shaft in the way so went via near side wheel to get mount out and back in 👍👍
Great videos SiRobb, thank you very much for all the effort!
Hope you don't mind if I come with some additional input regarding this particular replacement.
Remove the air intake hose that connects to the EGR valve or just loosen the clamp before jacking up the engine, otherwise you may damage it as it will be under a lot of strain if not loosened/removed.
The one above the starter?
hy SIROBB
very helpfull videos, great job!!!
i haven't found the test about the vaccum leak solved after changing you front and back mount.....did you solve the pupping noise doing that?
by the way, as the engine is still working well with the pupping noise, is it necessary to solve this vaccum leak?
regards
Merci pour tes videos.
Je ne comprend pas tout, mais les videos sont sympa.
Continus comme ca.
C'est mon plaisir
thanks for this, i was able to change the mounts following your steps.
Thans bud👍keep the vids coming I've nearly fix the whole car lol👍👍.
Great video tutorial, clear & easy instructions.
Thanks for this, really helpful videos good boy.
I have to replace the front one very soon. The rear one its all ready done.
Thanks again. And keep filming videos like that.😉👍
Thanks for the comment.
Thanks a lot for the video, I about to do the same work in my 2007 XC90.
Hi sirobb. Thanks again for your amazing channel. Unfortunately I'm going to have to do this job soon. I was wondering what tools you used to get the bottom bolt off the rear mount? It's something I've been dreading! How tricky was it?
Great video Simon as always - many thanks. I am going to do all five on my 2005 XC70 - the front and rear as shown in your video, the torque rod, side mount and engine mount. In your opinion, would it be best to support the engine, undo the bolts for the rear, front and side, and then replace those three in that order, not placing the top bolts on the rear and front until the side is installed? I can't help feeling that this would give some extra play when lifting the engine. A
Si Robb, did you have any vibrations, noises or any adverse symptoms prior that this helped with?
Outstanding video. Thanks for the help!
+Douglas Stephon..... and thank you for the comment. 👍
+Douglas Stephon ...... and thank you for the comment.
thanks buddy for video , you are the star
Thanks to this video I changed the front on my XC90. Unfortunately I could not change the rear one since there was no space to work. If anyone has a suggestion please help. I also heard a 'crack' while lifting e engine but the car is working just fine.
Thanks for the great video. I have aproblem in that when I lower the engine the tie strap goes loose. What am I doing wrong. It is a genuine Volvo part. Many thanks for your help. Barrie
Thanks for the video! A warning for xc70 D5 (2007) owners trying to do this job, this is way more complicated. There is no gap to take out the front mount The rear mount bolts are nearly impossible to reach. The top mount is easier but it slightly differs from this one. And jacking the engine up doesn’t release the front mount as shown on the video, for some reason.
how did you get the rear mount out? my kardan-shaft is blocking the way, so I couldn't reach it to get it out :(
Kl Simon , did you undo the lower driver side mount bolts aswell ?
SiRobb,
I want to say that all your videos are great! You are a true S60 guru.
Just want to ask, with your shot mounts, did you have a clicking(clunking/clanking) noise when you were pulling away or depress the clutch. Noise similar to the one when a lorry is changing gears.
Regards
Thank you for your comment but I wouldn't say I'm a guru. I just know what I know and hopefully explain things ok. ☺️
For your clunk, the more likely candidate is the gearbox torque mount in my video here czcams.com/video/PaxFMVqnMTM/video.html
Loose driveshaft bolts behind your wheel centre caps can also cause a similar noise so check the tightness.
They should be 50Nm, no less.
If both vacuum mounts are dead, your engine can also rest on the subframe so that's a possibility too.
Then there's the mount near the crank pulley......
Always try to nip noises in the bud because they never get better on their own and can lead to other things failing too.
Good luck. 👍
Thanks for good advice on changing coolant and flush. It was truly helpful and I managed to clean it all up and do a succesful coolant change.
I did also change the front engine vacuum mount successfully. The rear one, however, was impossible to get out after jacking up the engine and removing top nut and buttom bolt and vaccum hose. Therer was simply not enough space for it to com out. I have a 05 V70 D5 AWD, and that may vary from your car?!
I did the quick fix (temporary) that you posted some time ago and it worked good, but wantet to change the mount today, with only 50% success rate. Any advice on how to get the rear one out besides buying a Haynes or Vida? I dont have the software to run Vida just now and couldn't get hold of a Haynes manual before. My car is temporary out of order because I'm doing alot of service and replacements these days.
Do you know how to remove the clips for the side lower panels (under the doors between front and rear whells), by any chance? These have to come of in order to check for rust on the channels on each side of the car.
Thanks for charing.
Best regards, Arild ::)
I have an AWD V70 D5. Garage have stated that to access the rear mount, they would have to lower the front subframe as there is no room to get any tools on the mounts. Just to warn anyone with an AWD v70, it would be an expensive job. Like most jobs on an AWD. They are bloody awful to work on.
Rob, did you notice any difference after you fitted the mounts?
Fantastic Video. Thanks
Thank you for the video, I (not me, at the garage) recently changed two engine mounts on my Volvo XC90 2007 in Hong Kong. I would appreciate if you add sounds of your engine before and after. Thank you! I love my Volvo!
Nataliia Bezverkha czcams.com/video/-lgYAS3GoiE/video.html
Hi Simon. What car ramps do you use for your S60 - and do you use ramp extensions? Any reason you can't just support the subframe on axle stands for this job?
dickonprior I use the bog standard ramps from Halfords. About £20 each if I remember right.
The subframe doesn't need supporting for this job as it's not being undone.
It's the engine which needs lifting sufficiently to extract the mounts.
Useful video, thanks for taking the trouble to film this. I shall be replacing my front mount in the near future, just waiting for a new top torque bush to arrive before I tackle it. I too have opted for a Meyle part, what's your opinion so far? Having now replaced yours has it made much difference to noise or vibration levels? Thanks again and keep on making the vids.
Thank you.
I used genuine Volvo not Meyle.
I didn't trust an aftermarket part for a component that does such a critical and difficult job and the price difference wasn't that great.
The car feels noticeably smoother.
Hi,
Has any fitted the Masteeda brand of these? And are your thoughts?
Great channel Rob, one of the best on CZcams for advice and helping others
I just did my front 1 gearbox 1 and top mount just need to do rear 1 and driver side mount behind wheel thanks for the video
Great video, I have the same issue, I will try a to change soon. Just need the courage.
Take your time and don't do anything silly and you'll be fine. 👍😊
Hi can you pleas send me link to vlog in wich YOU desaktiveted day running lights .Kind regards Karol
Really good Video! 👍
excelente vídeo,thanks
Thanks for this video! I am about to do this job on my 1999 S70 GLT. Were you worried about damaging the inner CV by raising the engine more than 30mm? I've heard it's fairly easy to at least over articulate that CV.
I found it easier to take weight off the engine and remove the complete mounting only 3 bolts job done mounting wise in 10 mins
Great video, I found if you just took the weight off the mounting especially the front one then it was easier to undo the 3 bolt engine mounting and replace the vacuum mount that way because it was difficult to get the lift clearance I wanted....
Hi!
Should i redo the front mount screws before lifting the motor again to replace the back mount?
Or just tighten them all at the end when finished?
Thanks a lot!
André Salgado I have the same question. What did you do?
Hi there i have tried your trick but it is not working for me and my noise is there when i take of the oil cap!! But i know i have a pcv problem with my car as the pressure inside my engine blew the core plug above the crank seal! Serious job it was for me to fix.. 4 nights outside my houes taking out the gearbox, subframe ect so have you any tips so this doesnt happen to me agian??? I tried your trick and blew out my pcv oil trap! Air went in one hole and came out the one beside it! Any suggestions would be much appreiciated so i dont blow another core plug! Please advise me please what i could do now!
Yes thanks for sharing that very helpful :-)
Is there only 2 of them vaccum mounts? Thanks!
hello SiRobb compliments for the video ..... you know how do you replace the back support of a xc 90 d5 185 hp of 2007 ? Thanks !!
Hi robb! I have Volvo XC90 and may car losing power non boost it all! And have vacuum leaks an Service can found a problem! Can be a problem at engine mount or vacuum pump?
Hi SiRobb, thanks for sharing these videos.
Does the left engine mount not need to be undone in order to replace the front and rear mount ?
Take it you mean the right mount next to the belt drive. No just remove the bottom transmission link and to top mount bar. (when you remove the top bar watch out for the plastic conduit clipped on at the drive belt end). I also loosened the rear mount bolts before removing the front mount, even so the car did lift a bit and I raised the engine.
The lower bolt of the rear mount is a b***h on a LHD V70, there's power steering lines in the way. You need a 3/8" universal joint and a low profile 14mm socket (as VIDA suggest, but 1/2" joint/socket definetely won't fit). It's also quite easy to crossthread the soft aluminium of the mount when you put back in the bolt.
I've just bought new mount's for my car. They have changed the design of the rear mount but they have changed the bracket to match. I would not have known this if I had not gone to Volvo. So I think the extra cost was worth it less hassle in the long run
Hi Rob great Video, Can I ask I just got a new replacement Vacuum Mount and before putting it in the car I tested with a vacuum gauge same as yours but seems to have no vacuum showing on gauge is that normal ?
regards
Pete
Peter Hilsdon Hi Peter, no that isn't normal. You should be able to pull and hold a stable vacuum on a new mount, at least 20 inHg so ensure you have a good connection between the tester and the mount.
Thanks for that have sent back for a new one. On a different point jacked up the gearbox to remove the rear mount all fine,
but I seem to be unable to remove the old mount from the location you have shown, do I need to be jacking it further to create this space, or are some car different, mine is a 2004 xc 90 se auto model.?
Peter Hilsdon The AWD system creates a large problem for easy removal unfortunately so you may need to remove other components.
SiRobb cheers thanks for that will look at trying again :-)
Peter Hilsdon No problem. This link may help you too www.volvoforums.org.uk/showthread.php?t=260585
Thank you
Hello again SiRobb and thanks for another very useful video. My XC90 D5 (55 reg, 2006 model year) has engine mount problems, I think. When I accelerate from zero, or even from low speed, and also when I back off the accelerator, there is a definite "clack" or "clunk" sound from somewhere up front, I suspect in the engine bay. It also seems to transmit a lot of vibration into the cabin at idle, and when reversing and I brake, there is also a "click" sound. I did your inner tube trick to the gearbox torque mount about a year ago (great idea!) so I'm hoping that's still okay but D5s have about 5 or so engine mounts - lots to go wrong. My car has quite loud D5 "popping" when taking the oil cap off so it must have some sort of vacuum issues (mileage about 145 000miles . I ordered the vacuum tester via your Amazon shop link today (should arrive tomorrow) so I can test the front and rear mounts, but in the meantime I'm also curious about the upper brace mount (I think that's what it's called). It's the long black metal bar that goes across the engine with a mounting point towards left of the car's centre line and one at each end. Mine seems quite floppy: the black rubber mounting is loose and the metal bar can be easily wobbled back and forth by hand. I believe these are supposed to be a bit loose, but how loose? I feel mine just can't be right, surely? I link below to a brief CZcams video of mine so you can see how good or bad it is (czcams.com/video/7rIFRhqQ2es/video.html). Should I replace the top mount, and what about the two end mounts? Thanks again for great Volvo advice videos.
Hi Aidan. The video link is private so I can't see it.
Just needs the privacy setting editing.
@@sirobb Oh, sorry. I'm new to uploading CZcams videos. This link should work now. czcams.com/video/7rIFRhqQ2es/video.html
The clunking @9 seconds shouldn't be there and the main central silver mount with the square/cross shaped bushing has seen better days.
I would first see if I could pack out the centre torque mount bush with inner tube or similar like you did with the gearbox to subframe torque mount to reduce its movement.
@@sirobb. Great idea, SiRobb. Thanks for the tip and for taking the time to watch the video and advise again. Good old inner tube again. I'll give it a go and let you know the result. Thank you.
Just tested the vacuum mounts. Front one is totally shot. No vacuum held at all. Rear has a leak, could be the hose as I wasn't able to reach the mount this time, but it seems likely it's the mount as well due to age and mileage, but I'll try your pliers-on-hose trick tomorrow if I can reach it to be 100% certain about the mounting. The D5 popping stops when both hoses are disconnected at the T-piece and I block the holes with my fingers. So I'm hoping all is well with the rest of the vacuum system... fingers crossed. I'll also try the inner tube trick on the top central mount hopefully tomorrow. I'll report back when I've made further progress.
Sir thank you for the video
Does the s60 t5 have this vacuum nipples at the Hydro mount top too?
I have a new pair here, but they just have a sting next to the Bolt for correct Position i think.
Vacuum mounts are only on some D5 versions. No petrols have them.
Any advice on refitting the vacuum pipe? In particular the front mount. Mine seems way to small to connect. I’ve tried heating to stretch it. The pipe is the same diameter if not a touch smaller than the inlet nozzle. Is there an adapter my car is missing? I bought a new mount to replace the original which was obviously not working although there’s good vacuum. When I went to remove the old one the pipe just came away in my hand and it had been blanked off with a bolt and stuck in such a way as to look connected. I think my original mount may actually be good still. Please advise if you can. Cheers
You normally just swap things over from the old so if they're not available or suitable, you'll have to speak to a main dealer or measure the internal diameter needed (3mm?) and buy a cheap pipe connector.
SiRobb thanks for replying. I called the dealership and it seems like the vacuum pipe is correct. Bizzarrely they couldn’t tell me over the phone if it needed an adapter or what to do. I’ll get it done some how. Another little question I had was- there’s a little rubber stopper in the nozzle of the new one as there is in your vid. Is that just for packaging or is it needed? It looks to like the stopper is still in the original mount nozzle on the car?!?!
Hello. Thanks for great videos!!! I'm going to replace just the front one. Ordered an original Volvo. But I've noticed one little thing. There was a little black nipple where the pipe is attached to the mount. It has disappeared after you got that old front mount out. And there is NO nipple on the new mount( just some black ring)... So how did you get that vacuum pipe on the NEW engine mount after you have installed it. Thanks!
J Rukmanis The nipple just pulls out and is transferred to the new mount.
Just pull the nipple out before jacking up the engine to reduce the risk of damaging it.
Thanks for the comment.
Thanks very much for replying! Will do so.
@@sirobb I wondered the same. Now, mission accomplished.
Thanks!
Nice job, that rear mount looked to be a bit of a pain how long did it take?
If you're not filming it and talking people through each stage, it takes about 1 hour. :)
thanks
Great instructions but I managed to run out jack. Got to do some fieldservice tomorrow on a bigger jack thats been out of comission for a while. Probably needs just a good purging of air, perhaps a bit of hydraulic fluid to top it off aswell.
BRILLIANT now I know how to change mine! WHY do manufacturers build up all the sub frames etc thinking “yeah thats easy to get to”
THEN they bolt that subframe UNDER A CAR. Suddenly ........its impossible to access,😕 that rear mount looks awful. I have to replace a turbo on my T5 (TRANSPORTER) and thats half way up the block on the BACK of the engine a real bugger to get to? THANKS VW😩
Luckily i have found ramps with built in jacks so i can get my vehicles RIGHT UP to try to make it easier......still means working out in the rain with the cows though🤷🏼♂️ cheers Simon🤟🏻👍🏻
Great video,done my ones front is easy(say that it fail after 5miles trip stoped holding vacuum got replacement will visually investigate what happened)
Saying that rear one I wish I paid someone to do it 😅
No space to work whatsoever
My is 2010 XC90 d5
On your video looks like you got more space to work on rear one 😎
Yes the AWD models have much less room than I did.
Is it possible to do without removing angle gear on awd models? How difficult?
SiRobb is it possible on awd model without moving angle gear? Thank you
Anyone knows what is the steel rope on the mounts for?
This was missing on your rear engine mount.Thanks
Hello SiRobb. Thank you for your great videos.
I have a question, hope you can help me with this. I have an XC90 Diesel and there are some troubles with the boost. When the car is cold, the boost doesn´t work. But when the car acquires temperature begins to work normally. I saw the vacuum engine mount hose disconected and plug it in again but the trouble did not disappear. Can you give me an idea or some diagnose to find the precise trouble.
Im sorry for my english.
PLease help me
Which D5 do you have?
It is a 2009 D5. Im not sure the generation. If it helps, here is the las part of The VIN number... 91496006.
Please help me!🙏🏻🙏🏻 and tell me if you need more information.
Engine mounts don't affect your D5 engine and turbo performance. You won't solve this easily on your own without good diagnostics. Do you have any?
Hello SiRobb,
this is what the scanner showed me.
Hope that codes can give you more information.
- BCM- 0057
- ECM- 1507 boost control- pressure too low
- ECM- 1517 boost control pressure too high
- ECM- 1540 boost control pressure too high
I want to sell the car but I need to fix this trouble first.😭.
Thanks in advanced, have a great weekend.
great tips
Hi, great video do you remember the price u paid for both? My car is doing the popping noise n both mounts look finished so wanting to replace is it bad for the engine leaving them so long? Ive done 1.5k miles with the popping noise...
Leaving worn engine mounts places more strain on the other mounts which can lead to premature failure and more cost.
Make sure you test the mounts first because the popping noise is a vacuum issue and mounts aren't the only cause.
You could have perfect mounts and a sticking boost solenoid or knackered tcv for example.
+SiRobb thanks for quick reply but my car seems have no boost issues and turbo works fine i disconnected pipe going to mounts like in your video and the popping does stop ive cleaned boost and tcv and both look fairy new anyway think i will go out and buy a gauge first
+SiRobb did my test front mount is fine back one is shoot looks like yours haha so that is getting replaced and my lower RH engine mount 2 do you know if its difficult to do this mount? Thanks
+anth0ny1990 The right mount under the crank pulley is very simple.
Just 4 bolts which are all easily accessible.
Is that a silicon resonator delete visible on the view of the rear mount? My turbo system has a boost leak and I think the resonator is to blame. Reckon this is doable without ramps? Mines an XC90 2006, can't get into the garage until the 23rd.
No resonator here as it's a Euro 3 D5.
You can do oil changes on an XC90 on the ground so it's down to how well you can squeeze under.
Hello mate. I did this job many times and got tired of this allready.. It seems that oil pan is the lovest point of the engine.. i dont like this.. how about yours? I got both mounts changed and it still seems like its easy to hit somenthing and crack the belly pan. The mouts seems same hight as previuos ones..
Mine has a popping noise, clipped the silicone hose feeding the 2 engine mounts, the noise is gone.Does this confirms a faulty mounts Rob?
And a grinding noise from the vacuum pump too, but when I depress the clutch, the noise will disappear. I believe the clutch is vacuum assisted. What will be the process od fixing these?
Thanks.
+Rhonne Empleo The clutch is hydraulic and uses the same fluid and reservoir as the braking system so your noise is more likely to be a worn DMF.
SiRobb , I now detached the 2 vacuum pipes from rear and front engine mounts and blocked it, miraculously the whole noise were gone including the grinding noise from the vacuum pump. I have just purchased 2 engine mount with hydro bearing function online.
If I will attach again the vacuum pipes back to the engine mounts, I can feel a vibrations from the clutch pedal, but if I will detach them and block it, the popping noise from inside the oil filler cap is gone and the vibration from the clutch pedal is gone.
I will replace the engine mounts when they arrive, and will get back to you for results.
Thank you so much.
SiRobb, can a 5 speed auto transmission be replaced with a 6 speed auto box without any problems, if its the same year, make and model?
shane pepler Unfortunately, no.
i have an 08 3.2 awd. so similar yet so different. can anyone confirm that there are NO vac lines for the 3.2?
Great video. Where does the vacuum hose connect to the mount? Both the new part and old part don’t appear to have a plastic nipple. Thanks in advance.
You re-use the existing connector which should still be attached to the vacuum supply hose.
I see it now, thank you.👍
Спасибо большое! Было очень интересно! + + +
Без проблем. Спасибо за комментарий.
Thank you so much .why do theth alparts change?t is the cause of the problem
I have a question.
Is that you should not remove the motor support down next to the pulley dumper ?
Thank
No it's not necessary to unbolt that mount.
ok
Can someone help me with understanding the difference between a vacuum engine mount and the lower mounts which he also showed in this video that look different from the black ones? I have a 2003 S80 and I need to get the old mounts out sooo badly
That will help me as well buddy, thank you for showing how to dirt fingers,....
Thanks for the video, it has been very useful.
I want to change the rear vacuum mount, but I do not know how to access the lower screw, do I need to remove another piece?, please can you explain a litle more ?
Thanks
What is your car?
It is a Volvo 2004 XC90 D5 163cv automatic
My car is an S60 so doesn't have AWD components in the way.
I would suggest buying a workshop manual like Haynes or Vida.
Thank you SiRobb, I will follow your suggestion
@@sirobb Good evening. Hope you don't mind could I ask what name you go under on the volvo forum. I'd be really keen to hook up with you. Thanks so much for the videos. This really has helped! Best wishes Tony
Hello sir,
First thank you for your clears vidéos !
I changed the steering rack (not easy !). But i did a mistake, i removed the metallic support on the top of the second motor mount in your vidéo. And now i can put just 2 of the 3 screws witch fix it to the motor and gear box... i can’t put the 3 hole in front of screws places together. If you’ve got any idea how to process, I’ll be gra
forum.univers-volvo.com/archive/index.php?thread-23481.html
Piece number 20 on this schema
Hi Martin. The diagram only shows 2 screws to mount the bracket and one hole for the thread of the engine mount to pass through.
Hello, i saw that. There have a third one the top of this pièce. Maybe the millesime ? And maybe not si important. My car is lighter now 😂.
Î’ll ask to Volvo, thank you
Thanks rob.
Great vid
Great vid thanks heaps
Btw bad leaking mounts can display error for turbo pressure
Just bought a Volvo S60 and I think I have to replace mine, how do I found out which one it is and how much roughly is it for parts
+Baldy Bob I paid around £90 each.
See my list of videos for the testing procedure to work out which, if any are faulty.
Would this put strain on the side mount? Should that be unbolted too first ?
I wasn't concerned about the crank pulley mount and have had no issues.
It's only 2 bolts if you feel you need to release that too.
@@sirobb I just checked Vida. You don't need to. Thanks for the speedy reply
Just finished the front mount job. Bolt was stuck. Might do the rear one later in week lol.