@@GalaxyGames843 I spent more than $600 as well on upgrading…but my machine is at a gym where they pay with cards mostly. It’s super high traffic, so I’ll make that money back in a month or so.
**LOOK UP ESD** You need to be grounded with a ground strap when handling the control board. That's why it's in that silver package. Research ESD (Electrostatic Discharge). Handling the board as you did, has a strong possibility of damaging the board by static shock. It will probably work for a while but after a few months or a couple of years if you're lucky, the board will go bad and you're calling tech support to figure out why. This is not a well known thing unless you have experience and training in electronics handling. Only then you'll learn how much it is stressed just how bad ESD is to electronics.
Thanks for the tip. I've been working with circuit boards for many years and haven't had that issue come up yet, but thank you for bringing it to my attention
Like all CZcams safety monitors, ESD is drastically over exaggerated. If it was going to harm the board, it wouldn't function immediately after the static discharge. There is no real possibility for some undetectable future issue to be caused taking it out of the bag. Either it's smoked or it's not.
@@ronlabe5487 Then good luck to you. All I will say is you will be fired in a heartbeat if you disregard ESD handling rules as an assembler/inspector/engineer from any reputable electronic manufacturing company worldwide. Just saying
@@chavezvale59 I usually don't change the validator and coin mech at first. I tend to just let them stay in the machine till they need to be serviced then i replace both to mdb. I am at the point where i only buy mdb validators and coin mechs.
Hi, what a great video, I never expect to find a video as specific as that (exactly answers my question). I followed the link you suggest, but there are a lotof mother board, can you help me with which one should i choose for my Seaga HF3500. thanks
I have an old Vending Machine (Merlin III). When I decided to buy a Kit to upgrade it, the seller said that I need to update the MDB version inside the chip in the board (EPROM?!?). I am a programmer, understand circuits, but I just understand the basics of MDB. How can I perform this update? Any IC writer device? Via socket/jack? Thank you in advance!
Sometimes its better to just buy a machine that is already compatible for card readers… the additional cost of an MDB bill changer, coin mech, the upgrade kit & your time to convert everything 🤔 might be too much
@@GalaxyGames843 can you please give my channel a shout out in your community tab? I have heard that when you have 500 or more subscribers, you’re able to do that, and it does help channels. Thank you very much! Keep up the great 👍🏼 content!
I just came across this video doing research looking into getting into vending. This may be a newbie question, but here goes. Can you get an older machine in good shape and change the boards out to accept the credit card readers?
Some machines yes - but not all - It depends on if an upgrade board is available for the model you are looking to buy - there isn't an upgrade available for all machines out there
Hi I am new to the business and this is so helpful because one of my new machines needs to be updated. It's an AP 113. I was told that if I upgrade the control board, I have to also upgrade the bill collector and the coin collector. Is that true? You mentioned getting the MDB codes once installing- what does that mean?
The AP machines will most likely need a new compatible dollar bill acceptor and coin mechanism if it doesn't currently have compatible ones in there. As far as the MDB codes... those are the internal machine codes that report to the cc reader when managing inventory inside the machine.
@@GalaxyGames843 I just realized that my AP 113 is an older model. The display unit is behind the bill collector instead of behind the new control board. Any videos with that type of vending machine?
I wasn't familiar with that particular machine. I did look it up and it doesn't seem like a kit has been manufactured to make that machine work with credit cards
I ordered from D&S vending and no they aren't compatible with every older machine. Find your machines model number and go to that website to see if a kit is available
I got a AP studio one snack machine when it was bought it was set up just for card reader it has no coin Mac no dollar bill validator nothing do you know how to set it up for regular and if so could you take a picture of your machine if you have one and send it to me I am really stuck with this and I’m just starting out
Hey here watching I have automatic product I been told I need to change motherboard control for the card reader will this video helps for the automatic product snack machine too
@@GalaxyGames843I just find out i probably can upgrade the coin mechanism and a adapter that plug in the mult drop bus (MBD) a guy told me try that first if not update the board I have LMC1 automatic product snack machine
You would need to upgrade it like I did to this machine in this video... Here is the new board you would need: www.dsvendinginc.com/p-2253-d950a-1-inone-kit-ap-40005000-series-machines.aspx
@@joshyjosh214 check out shop.nayax.com for the most current prices. If you decide to buy, use coupon code galaxygames843 and they will take more money off of the price
Great Video! We are always pleased to see our products being installed IRL. Thanks for the feedback!
Thank you so much for the comment! Love the product!!!
I did an install on this exact same machine and bought the InOne from D & S as well!! It was easier to set up than I thought!
Very easy!
@@GalaxyGames843 I spent more than $600 as well on upgrading…but my machine is at a gym where they pay with cards mostly. It’s super high traffic, so I’ll make that money back in a month or so.
@@chrisseverin6370 exactly how my location is
**LOOK UP ESD** You need to be grounded with a ground strap when handling the control board. That's why it's in that silver package. Research ESD (Electrostatic Discharge). Handling the board as you did, has a strong possibility of damaging the board by static shock. It will probably work for a while but after a few months or a couple of years if you're lucky, the board will go bad and you're calling tech support to figure out why. This is not a well known thing unless you have experience and training in electronics handling. Only then you'll learn how much it is stressed just how bad ESD is to electronics.
Thanks for the tip. I've been working with circuit boards for many years and haven't had that issue come up yet, but thank you for bringing it to my attention
Like all CZcams safety monitors, ESD is drastically over exaggerated. If it was going to harm the board, it wouldn't function immediately after the static discharge. There is no real possibility for some undetectable future issue to be caused taking it out of the bag. Either it's smoked or it's not.
@@ronlabe5487 Then good luck to you. All I will say is you will be fired in a heartbeat if you disregard ESD handling rules as an assembler/inspector/engineer from any reputable electronic manufacturing company worldwide. Just saying
@@pjackson8322 Peter, we really need to talk about your TPS reports.
@@ronlabe5487 I'm not peter.
These boards are really good. I have installed like 20 of these.
Hello, I have a question. Did you also change the validator bills and coins, or just the board? I'm very confused, help please.
@@chavezvale59 I usually don't change the validator and coin mech at first. I tend to just let them stay in the machine till they need to be serviced then i replace both to mdb. I am at the point where i only buy mdb validators and coin mechs.
Absolute great video! Very great attention to detail very much help! Very well educational video user friendly !! Keep up the great work
Glad you found it helpful!!!
Hi, what a great video, I never expect to find a video as specific as that (exactly answers my question).
I followed the link you suggest, but there are a lotof mother board, can you help me with which one should i choose for my Seaga HF3500. thanks
I have an old Vending Machine (Merlin III).
When I decided to buy a Kit to upgrade it, the seller said that I need to update the MDB version inside the chip in the board (EPROM?!?).
I am a programmer, understand circuits, but I just understand the basics of MDB.
How can I perform this update? Any IC writer device? Via socket/jack?
Thank you in advance!
Awesome video buddy can't wait to see the next one and the diesel shop
Thanks! I have one filmed there but haven't edited it yet!
@@GalaxyGames843 can’t wait to see you get a card reader there :)
@@720vending here is a hint - it's already done and filmed! Video to come!
Great work Matt!
Glad you enjoyed it
Awesome 👌 video man
Thanks! I hope you found it helpful!
Thank you for the helpful video can you please share from where we can order the board? thank tou
That button cell battery is to keep the time correct in case power outage(blackout)
Yes! it is a good thing that is on there! it should keep all the price settings memorized also!
@@GalaxyGames843 yes I’m not sure if the old board even had that 2032 battery!
@@VOLTRONDEFENDER4440 I've worked with other boards that have had different types of batteries
Will this work on api model 113
Did you install the door switch?
How can I find out of there is a kit for the machine I have?
What is the machine's model number? I usually just compare it to what kits are available on D&S Vending and Vendors Exchange websites
Sometimes its better to just buy a machine that is already compatible for card readers… the additional cost of an MDB bill changer, coin mech, the upgrade kit & your time to convert everything 🤔 might be too much
I can see your point. But since I got this machine for such a great price to begin with it was still worth it
@@GalaxyGames843 can you please give my channel a shout out in your community tab?
I have heard that when you have 500 or more subscribers, you’re able to do that, and it does help channels.
Thank you very much!
Keep up the great 👍🏼 content!
@@geminivending I can do that, but you need to post more videos on your channel in exchange!!!
@@GalaxyGames843 working on it. Shorts are working better for me atm
I just came across this video doing research looking into getting into vending. This may be a newbie question, but here goes. Can you get an older machine in good shape and change the boards out to accept the credit card readers?
Some machines yes - but not all - It depends on if an upgrade board is available for the model you are looking to buy - there isn't an upgrade available for all machines out there
So where do you find out that information?
@@GalaxyGames843how are we supposed to find out?
How much is the kit?
This one was $385
We have the same machine can you tell me what light bulb size it uses ?
Honestly I am not sure, when bulbs in machines go dead, I retro fit with LED lighting
I'm new at this. How should I approach a business owner about having my vending machines imat their business? Do they charge?
Just ask them if they need vending machine services! Tell them it is free of charge to them!
Hi I am new to the business and this is so helpful because one of my new machines needs to be updated. It's an AP 113. I was told that if I upgrade the control board, I have to also upgrade the bill collector and the coin collector. Is that true? You mentioned getting the MDB codes once installing- what does that mean?
The AP machines will most likely need a new compatible dollar bill acceptor and coin mechanism if it doesn't currently have compatible ones in there. As far as the MDB codes... those are the internal machine codes that report to the cc reader when managing inventory inside the machine.
@@GalaxyGames843 I just realized that my AP 113 is an older model. The display unit is behind the bill collector instead of behind the new control board. Any videos with that type of vending machine?
@@angelakthomas1774 my apologies I don't have a video for that model!
how can i get a motherboard for a gaines vm 750 A vending machine to take a credit card reader
I wasn't familiar with that particular machine. I did look it up and it doesn't seem like a kit has been manufactured to make that machine work with credit cards
Where did you order yours from? And is it compatible with any older vending machine?
I ordered from D&S vending and no they aren't compatible with every older machine. Find your machines model number and go to that website to see if a kit is available
What’s the name of the company in Ohio for the kite
D&S vending
I got a AP studio one snack machine when it was bought it was set up just for card reader it has no coin Mac no dollar bill validator nothing do you know how to set it up for regular and if so could you take a picture of your machine if you have one and send it to me I am really stuck with this and I’m just starting out
Without a mech or a DBA the in one board should still be able to connect to a card reader... You can always add a MDB mech and dba later
Can you install these on the old brown ones ?
That's kind of general. You would need to check to see if in one makes an upgrade board for whatever model you are referring to
vmc vending machine controller
Thank you for the info!
Hey here watching I have automatic product I been told I need to change motherboard control for the card reader will this video helps for the automatic product snack machine too
Yes the process should be very similar yes!
@@GalaxyGames843 ok
@@GalaxyGames843I just find out i probably can upgrade the coin mechanism and a adapter that plug in the mult drop bus (MBD) a guy told me try that first if not update the board I have LMC1 automatic product snack machine
Good info, but next time do us all a favor and mount the camera in a good position. I feel a little sick now!
Sorry about that!
Is this required to install a card reader?
@@ohyeahthatsright3155 depends on the machine
@@GalaxyGames843 Thank you for the prompt response and sharing your knowledge.
@@ohyeahthatsright3155 you got it!
Can I add electronic payment to an 80s Coke/Pepsi machine?
Technically yes, if you take all the electronics out and put in all new electronics yes, but honestly Id just get a newer machine
@@GalaxyGames843 you are so correct. After discovering more information it's really not worth the investment in an old machine. Thanks for replying.
What type of vending machine is this?
It's a USI (now wittern) vending machine
@@GalaxyGames843 Thanks
Can I put a card reader on a SnackShop 4000 ?
You would need to upgrade it like I did to this machine in this video... Here is the new board you would need: www.dsvendinginc.com/p-2253-d950a-1-inone-kit-ap-40005000-series-machines.aspx
What display board did you use?
The kit came with the new display board
Are AP 4600’s compatible?
This is the board you would need for that: www.dsvendinginc.com/p-2253-d950a-1-inone-kit-ap-40005000-series-machines.aspx
Where can I purchase this kit
I got mine from D&S vending
How much does the card thing cost
Do you mean the Nayax credit card reader?
@@GalaxyGames843 yes
@@joshyjosh214 check out shop.nayax.com for the most current prices. If you decide to buy, use coupon code galaxygames843 and they will take more money off of the price