Heat the bearing and ring in the future. You can take it off without any problem. This way, you can easily damage or bend the axle. The same for assembly. You heat up the bearing, slide it over the axle without any problems. After cooling, it will tighten on the axle. It's the samor you do with the ring. You don't force these bearings into place.
So on this type of beer and axle, you don’t necessarily have to take the plate off the rear end because it comes right out without any sea clips like other Chevy GM rear ends. Is that correct
He’s got it backward! Take it apart with the hammer; reassemble it with the press! And I think I remember that the bearing was sealed on only one side; the seal should be outboard.
For others that may read this. There are 2 types. Early BOP 10 bolt axles like this one(66-69) has the seals inside the tubes and a sealed bearing held on the axle with a wedding ring. Later BOP 10 bolts (71-72) have the seal and open style bearings held into axle by wedding ring.
NOT the recommended way to remove the bearing! He’s lucky the top of the axle didn’t slip and launch the axle into his face! Use a cutoff wheel to cut most of the way through the retaining ring, then lay a cold chisel parallel to the axle. Couple of hits with the BFH will split the ring.
Hi,Jenny Lee here with NTD Television. Our team was very impressed by your video and our editors would like to showcase it by uploading and crediting you on some of our social media pages and websites so that our fans can see it. We are one of the world's fastest growing media companies with over 100 million fans and 1 billion monthly video views across all of our social properties. Our motto is truth, hope, and humanity. Can I send you more information in my next message / email? Thank you! Jenny.lee@ntdtv.org
Your videos are great!
Heat the bearing and ring in the future. You can take it off without any problem. This way, you can easily damage or bend the axle.
The same for assembly. You heat up the bearing, slide it over the axle without any problems. After cooling, it will tighten on the axle. It's the samor you do with the ring. You don't force these bearings into place.
So on this type of beer and axle, you don’t necessarily have to take the plate off the rear end because it comes right out without any sea clips like other Chevy GM rear ends. Is that correct
That is correct
So theres an axle seal on the inside and outside or just inside? My axle came out on the track so Idk what order the parts go in
On my axle there was only one seal per side and it was at the outer ends of the axle tube.
Bearing splitter or a cutting torch.
Where did you get the new bearings? I can only seem to find bearings for Chevy 8.2 not BOP
I got them from napa
The parts place has the complete kit # SU3211Z
Do you have to remove any clips inside the pig? I unbolted the four nuts but axle doesn't budge
I didn't have any clips
Old buicks n pontiacs dont have any clips ..but a lot of others do
Just keep pulling. They get sometimes
He’s got it backward! Take it apart with the hammer; reassemble it with the press!
And I think I remember that the bearing was sealed on only one side; the seal should be outboard.
For others that may read this. There are 2 types. Early BOP 10 bolt axles like this one(66-69) has the seals inside the tubes and a sealed bearing held on the axle with a wedding ring. Later BOP 10 bolts (71-72) have the seal and open style bearings held into axle by wedding ring.
NOT the recommended way to remove the bearing! He’s lucky the top of the axle didn’t slip and launch the axle into his face!
Use a cutoff wheel to cut most of the way through the retaining ring, then lay a cold chisel parallel to the axle. Couple of hits with the BFH will split the ring.
Where you guys out of?
Hi,Jenny Lee here with NTD Television. Our team was very impressed by your video and our editors would like to showcase it by uploading and crediting you on some of our social media pages and websites so that our fans can see it. We are one of the world's fastest growing media companies with over 100 million fans and 1 billion monthly video views across all of our social properties. Our motto is truth, hope, and humanity. Can I send you more information in my next message / email?
Thank you!
Jenny.lee@ntdtv.org