How To Replace the Starter Clutch on a Honda CRF250/450X & TRX450ER
Vložit
- čas přidán 26. 08. 2024
- Shop Now | Honda CRF250/450X & TRX450ER Starter Clutch Replacement www.rockymount...
If you can hear your starter spinning but not engaging and actually turning over your engine, there's a good chance your one-way starter clutch or reduction gear is damaged and in need of replacement.
In this video Charles shows how to replace the starter clutch on a Honda CRF450X, but this process will be similar for Honda CRF250X and TRX450ER's.
Check out www.rockymount... for all your parts, apparel, and accessories!
Click Here To Subscribe To Our Channel!
/ @rmatvmc
Follow Rocky Mountain ATV/MC On Social Media!
FACEBOOK: www.facebook.c...
INSTAGRAM: www.instagram....
TWITTER: RM...
Excellent video thanks RM!
Hey Charles do you happen to have a video on installing the Kickstart kit on a 06 trx 450er? Any information would be helpful thanks, and your videos that helps me out a lot.
Your videos are really helpful, thank you 🙏
Happy to hear that, you're welcome!
Wow! What a helpful video!
I own a CRF450X as well and also have a problem, guys maybe you can give me an advice, I would really appreciate it. My starter makes only one turn or sometimes even half a turn, symptom is like a battery died, however it's fully charged. When I take starter off the bike and apply some voltage to it from the bike's battery - it runs well. What could possibly be the problem? When I use kickstart, engines goes with the first kick.
I'm assuming your battery voltage is around 12.8 volts with no load, right? Still a lead acid battery? Use some alligator clips on a digital multi-meter and check the battery voltage while hitting the button. If your voltage hits 8 or lower with the starter button pressed, then either recharge the battery then test again or replace the battery with a new one. Other than that you would have to check if one of those gears are binding up, but that is less likely to happen. -Charles
@@rmatvmc Whats the torque specs on the cover?
Are lining up the starter clutch and the gear on top to the same dot critical? I’m not sure if it’s exactly lined up..
So finally tore into mine today and get my starter clutch out and can’t turn it either way no matter how hard I try what would this do when trying to start as mine would get right to where it seemed like it was about to start and then just would stay there and not fully start
Which way should the starter spin when your looking at it from inside the case because mine is spinning counter clockwise which seems to just slip the starter clutch and not turn over the motor
06 Honda Trx 450er is having the problem where the starter sounds like it’s slipping. Better have look at it. Replace the clutch bearing.
Hello,i was thinking ,if is possible to fitting the electric starter kit from fx to fr
Tremendo video solo le falto el subtitulado al español
Hello! Thanks for making this very informative video. However I have a trx450er and the stater clutch assembly didn’t come out as a whole and the one way clutch hun is stuck on the splines. Any advice to removing it. I cannot seem to find a bearing puller small enough. Thanks!
Hey man I ran into the same problem. You need to find a regular gear puller that's what I used
Great video.
I have a problem with both starters, when the electric kick starter fails, something inside also does not turn, after a few kicks it gets better and now it can start with both!??
Hmm... Let us know what you find! -Charles
Does the TRX 450R 2006 have these starter clutches? I know of 1 450R with this same problem.
Yeah, it's going to be a similar set-up. Double check part numbers though. -Charles
When loosening the bolt on the clutch hub/basket, does anyone else always break the little splines on the clutch hub with the clutch hub holding tool? I've done this twice, once on a CRF250 and once on a CRF450....am I doing something wrong or is the clutch hub just that fragile?
Some of the Honda's that are newer than the bike we are working on in the video have a magnesium clutch hub. They are definitely more fragile. Normally it's easier to use the clutch holding tool, but with those, you might have to try different measures like putting the bike in gear and using a sprocket jammer to lock things up. czcams.com/video/e3gqZ5ZeD7M/video.html, czcams.com/video/4Hq4Xc7Wn0Y/video.html -Charles
I literally just went through this disaster myself 😶
I did too
I got a crack case On my Honda 450x where can I buy a new case
You might be able to find one on the OEM Parts page of our website. Enter the year/make/model.
750 miles from new and mine is shot, thanks Honda........ :
What kind of bike is this
I have a 06 trx 450 when I try and tighten primary driveshaft bolt it spins all the other gears and won’t tighten any advice? Do I have to be in neutral or in gear for this to work like in the video
I have the same issue
My one way clutch will not go back on the shaft nor will the other gear that goes on the shaft. I’m putting them on the right way
I've got same problem with Chinese parts. What did you end up doing?
@@backyard-builds19 just buy oem. Thats the easiest solution.
Completely missed how to replace the one way bearing..
Really wish you didn’t fast fed through some of the stuff like showed us where washers go and also how the clutch plates go back in
They have a separate video that shows you the whole procedure for doing the clutch.
@@carsnquads thanks
Show,me,how on,a m0to,yamaha 350