I heard its good practice to pour oil into the new compressor and turn it by hand 10 times before installing. I was hoping this vid would show a way of adding oil with the system pressurized Edit: I had a clutch coil fail on me. I released some pressure from the lo psi line & shot out green gel likely from over oiling the compressor. Could be freon dye, but I also had green crust around the bolt holding the clutch on
Listen I’m gonna change your life, connect all hoses and open everything turn vacuum pump on and disconnect the red hose from the manifold pour the oil into the red hose the system will be infinitely vacuuming because blue gauge is still connected just pour away into red hose
OK from what I think has happened, the system has already been evacuated to extract remaining gas & moisture with the from the system. The high/low manifold guage valves have since been turned off before switching the evacuation pump off. After pump has been turned off, the centre manifold hose has been removed from the evacuation pump. The centre hose has been put into the cap of referent oil. Remember the manifold high & low hoses attached to the air-conditioning system "negative" pressure. The hose removed from the evacuation pump is placed in the cap with refrigerant oil. The low pressure gauge valve has been opened just enough to suck the oil from the cap into the low side of the system. You can proceed to gas the system up through the low side only. Make sure you know the capacity weight of gas to put into the system. Understand your high & low pressure readings on you guage when the compressor kicks in.
ضغطت (لم يعجبني) وبغادر المقطع في ثواني والسبب هو وجود الموسيقى، وصحيفتي فيها اللي يكفيها، الله يهدينا ويصلحنا. الأفضل الابتعاد عنها يا أخي، هي سيئات جارية عليك.
I wish there was an actual technique to know exactly how much we have in the system and how much to add when replacing a system part…a lot of guessing 😅 I hope I’ll do it right. I’m changing the condenser and the dryer box
اوستا اینکارو اشتباهت اینکار باعث میشه این مقدار روغن فقط تو شیلنگ ها بمونه شما حداقل باید 80cc روغن اضافه کنی در ضمن اواپراتور وکندانسور رو هم باید بشوری دوست عزیز
Once you do this you got to vaccum the system again
Im not a technician but i think with that amount of oil it just wet the hose yellow line and blue line.
This is great! Just never do it to your AC system, and you’ll be fine!
I heard its good practice to pour oil into the new compressor and turn it by hand 10 times before installing. I was hoping this vid would show a way of adding oil with the system pressurized
Edit: I had a clutch coil fail on me. I released some pressure from the lo psi line & shot out green gel likely from over oiling the compressor. Could be freon dye, but I also had green crust around the bolt holding the clutch on
Listen I’m gonna change your life, connect all hoses and open everything turn vacuum pump on and disconnect the red hose from the manifold pour the oil into the red hose the system will be infinitely vacuuming because blue gauge is still connected just pour away into red hose
Hell yeah way to fuck up a system
While letting in pounds of atmospheric pressure filled with moisture
OK from what I think has happened, the system has already been evacuated to extract remaining gas & moisture with the from the system. The high/low manifold guage valves have since been turned off before switching the evacuation pump off. After pump has been turned off, the centre manifold hose has been removed from the evacuation pump. The centre hose has been put into the cap of referent oil. Remember the manifold high & low hoses attached to the air-conditioning system "negative" pressure. The hose removed from the evacuation pump is placed in the cap with refrigerant oil. The low pressure gauge valve has been opened just enough to suck the oil from the cap into the low side of the system. You can proceed to gas the system up through the low side only. Make sure you know the capacity weight of gas to put into the system. Understand your high & low pressure readings on you guage when the compressor kicks in.
ضغطت (لم يعجبني) وبغادر المقطع في ثواني والسبب هو وجود الموسيقى، وصحيفتي فيها اللي يكفيها، الله يهدينا ويصلحنا.
الأفضل الابتعاد عنها يا أخي، هي سيئات جارية عليك.
6ft on non condensible just contaminated the system lol
Nice you added oil to the hoses and not the compressor
I wish there was an actual technique to know exactly how much we have in the system and how much to add when replacing a system part…a lot of guessing 😅 I hope I’ll do it right. I’m changing the condenser and the dryer box
I’m doing the same this week. How much oil did you add? I’m thinking 1oz
@@christianmoss2395
I added one oz in the condenser and it works great
@@christianmoss2395 oh by the way I only changed the condenser, if you change other parts you have to take that in consideration for the amount of oil
اوستا اینکارو اشتباهت
اینکار باعث میشه این مقدار روغن فقط تو شیلنگ ها بمونه شما حداقل باید 80cc روغن اضافه کنی
در ضمن اواپراتور وکندانسور رو هم باید بشوری دوست عزیز
Bass background
you will vacuum again, you will draw back the oil you have given
That’s a dumbest thing you could do to the AC system.