Programming Electric Scooters for 10-Setting Variants (P0-P9)
Vložit
- čas přidán 31. 05. 2019
- NEW 13 July 2019 Update
Full translation user guide here:
drive.google.com/open?id=1c0H...
The start of the video makes me look like I have the shakes, it's just a flaky camera!
This is a quick explanation of the 10 parameters available on most of the current Chinese scooters, especially the T11x range.
Care should be taken when changing any parameter and make a note of your existing settings.
P0 Wheel Motor Size for speedo calibration inches 0-99 (11)
P1 Low Voltage Cut-off 12.0-56.0 (520)
P2 Motor Pole Pairs 0-99 (16)
P3 LCD Display On/Off 0 or 1 (0)
P4 KPH or MPH 0 or 1 (1)
P5 Kickstart 0 or 1 (0)
P6 Cruise Control 0 or 1 (0)
P7 Power Start 0 or 1 (0)
P8 Power Level Dial Back 1-100 (100)
P9 Regenerative Braking 0,1 or 2 (1)
The P9 option is well worth investigating. You need to find the right balance here; if used in mode '2' you will lose the benefit of freewheel riding but gain battery trickle charging and if you ride in a very hilly environment, will save brake pad wear. But the electro-braking can snap in hard and unpredictably as soon as you release the throttle. If riding mostly on flat terrain, best to turn off completely. At the moment I use mode '1'.
Extra LCD Info:
TIME:Means Time from switching Scooter on
TRIP: Means single trip mileage (can be reset by holding MODE button)
ODO: Means accumulated mileage
DST: Means range of scooter in real time time with remaining battery
VOL: Means battery actual voltage
CH 2：00 : Means after 2 hours scooter will sleep if not used
Please share your thoughts... - Auta a dopravní prostředky
without a doubt, the most comprehensive guide on the whole internet right now, thank you dear sir!
Very kind of you Ollie, cheers!
@@marcusorobertsp1 max 445 help me
Helpful video ...excellent explanation , thanks for sharing 😃
Cheers!
I have an Ultron T108 1600WX2(5400W peak) 35Ax2controllers 60V 17ah 100A discharge (old battery) , May you please elaborate further on P2(motor pole pairs)?
This is used to tweak the timing, similar to advancing or retarding the ignition in a car..
As well thank you for you video. Very informative!
Cheers Cardwell!
Hello, can you tell me how to display the battery on the LCD sceen?
i have my way quick 36v any suggestion for this settings to and more speed and safety of baterry hope you can give me some advice
This helped a lot thanks 😊
Thanks Alessio
Hello. My display shows a lil box blinking and I can’t run the scooter? Had empty battery signal also but I lowered they threshold to about 33V. Can you help on that lil box and why is it their ?? I’m exhausted and can’t get my bike to run.
Based on the new infos, i wnated to test out and set the P6 to 1, so I wanted to have cruise control, but surprisly it did not go off when I pulled the brake but still accelarated like hell without pulling the throttle...was quite frightening...
the other interesting experience that if I am riding around 25-30 km/h and want to speed up from that speed, it doesnt allow me to do so, even if i turn on turbo and 2 wheels on. But if I start from 0 km/h and accelarate continously without braking or pausing it can go to higher speed too.... Do you think it is because I change turbo/economy mode during riding or? thanks a Mate!
cruise control worked,but braking not disable it. it accelerate it back. who need cruise control when its this dangerous.and who need over 25kph max speed limit anyway. you need ride scooter on bicycle lane. and road you cant ride it.every youtube post violate it lol
hey I have this exact lcd throttle. it was working fine but the display slowly fate off and I can't see anything from the lcd screen now. the throttle still works. just the lcd. do you have any idea how to fix?
Hi, does the scooter still have full power and the throttle reacts as expected, or is it just the LCD that cannot be seen? The LCD appears on normal brightness then dims naturally or when you apply the throttle?
Hi I have a 52v 18.5 scooter and I had a question for the p1 setting I have it set to 43.5v cut off but it seems to cut off at 52.8v it was weird because the scooter felt like it still had full power right until it turned off plus my battery on the controller displayed 3 bars left
Great video bro appreciate it how do you set it to the fastest mode I saw a CZcams video about removing the speed limit and leaving it on dual Drive will that be the trick that was On PO8 set to 100 on the d+6
Yes p8 set to 100 as default, but removing the speed limiter cable will only remove the cruise control and in other scooters, the electronic gears.
Are these for all scooters with the finger throttle display with p settings or for a particular scooter
i tried disabling the electric brake with p9 because in my scooter is busted and is quite useless to be honest
sadly that didnt fix the problem my scooter still wont accelerate :(
any idea where i can get parts for it??
im from chile so is nightmare to me ill have to import but even that is being dificult to find
Thanks for the video share this helps alot i have the 36v but my settings only go to p6 just wondering why? Only to p6
Thanks. Is yours a dual motor? The best thing is to use the p9 guide and just subtract want you need. Things like under voltage protection will be different ie lower, but the rest might be similar. Cheers.
Is P5 a kind of 'power delay'? if it is set to 1 it gives you instant reaction/power when you pull the throttle, and gives kinda delay if you set it to 0? thanks
P5 is a setting that ensures you 'push' the scooter before the power cuts in. I set to '0'. P7 is the power setting for quick start. I set to '0'.
Also, just to let you know I have a dual 2000w 60v scooter. When fully charged it reads 68.1v on the display, what would you set P1 to?
Hey I have worked it out, I have set it to 52.0 as this is the highest it can go actually, makes sense as to why it died on me earlier!
@@electchick_ Yes that's good. 520 (52.0) is the correct setting.
Hello Marcus. Great Work. I do have one of those Chinese scooters received two days ago with very similar controller to yours. I do have problem. Back engine stops working after few km. I am wondering if this is a matter of settings or electrical fault. Controller does not show any faults.
Back engine goes back working after a while. What could cause it. Thank you for your help.
Hi and thanks Sebastian. What happens when you switch on dual motors, does the rear motor still stop and the front motor continues to work? It is not a matter of a settings. The best thing is to place the scooter on a block and run it and see if it cuts out after a while. I know it is not running under load. If it doesn't cut out, then it's probably a loose connection caused when you ride under load in a real environment.
@@marcusoroberts Thank you. I hope So. I Tried to elevate the scooter and run for a while but as you wrote it would take a while. When on twin engine only front works and speedometer freezes. When only on front engine it works a bit slow seams half the power only in front wheel. Doesn't spin that much when it does when both engines are ingaged like it worked in some emergency Mode. I Will do Another test this evening and make a movie. Otherwise this is hell of a scooter. So fun and comfy. Awsome maschine
Hey mate my d6 wont fully charge to 58v it only reach 54v do i need to change my p1? Please help me and how many v should i put to fully charge?
Hi marcus roberts...
I've got the speedway mini 3
48v 15.6AH
electric scooter,
what should i set it???
Hi Petra, does this have 10 or 20 settings on the LCD? It should be set to default by the manufacturer, are you having problems with a particular setting that makes the Speedway not behave correctly?
Hey mate my d6 wont fully charge to 58v it only reach 54v do i need to change my p1? Please help me
I have a bs 13 and when i went to that mode my speed meter does not go up even when im drivibg with the scooter
Hello, good job with the video - very helpful. Do you have any information about usb data connection/software and its possibilities?
Hi and thanks. Unfortunately I don't have that info. I tried many contacts and went to the manufacturer of this LCD throttle, but they very protective of that.
They say me the usb is usless only for manufacturer use
Thank you, very helpful.
Rated voltage 48v has to have a caution approx 42 ISH? Or is about input voltage? Your scooter example has a 60v rated? And can you ride it on last drop voltage as Xiaomi for ex.?
Hi Radhu, that's correct. For a 48v scooter you could probably safely set to 32V. This is to protect the battery and the BMS. I set my 60V to 52V but could be anywhere between 43-53V.
@@marcusoroberts Thanks Marcus, a 50-80% of rated power will keep my travel shorter but battery healthier-correct?The customer service said 41.5... Hope my BMS automatically limits for my langfeite l8s. Plus is the winter low battery charge damage too...never had so many concerns with my previous Xiaomi! 😁
@@radhuchristian8406 yes, correct. But maybe the Xiaomi had the voltage limit preset, perhaps, and not user adjustable..?
Hello Marcus
I have a 48v scooter with 10 inche wheels and i set it down to 36v it is ok to set the volts down from the regular voltage if the scooter???
Hi Jonel, I guess you mean the setting for undervoltage protection, in this case P1? I would reckon for a 48v scooter around 38v-41V is fine. You would also get away with 36v but it's pushing near the low end of the battery tolerance before damage may occur.
Hi Marcus, what low voltage you would set for a 29Ah 60V system? Now it is set to 52V...is that fine? Thanks a lot!
Hi Balazs, yes for a 60v scooter it should be around 52 or 53 for added undervoltage protection to the battery. Cheers!
Marcus Roberts thanks Marcus. Do you think I bought a weak battery to an 5700W dual motor setup? 29Ah and 60V...so either I should buy a bigger battery or I should lower the motor power from the menu P8, lets say to 70?
Hey man , thanks for the video, I was wondering about P1 , I’ve got the T11, 52V scooter what should I set it?
Hi, I would recommend 385. The battery's internal BMS might kick in sooner or later, but be safe and set as that. Cheers
Marcus Roberts are you sure mate? It’s set as default as 450, my scooter is 52.4V and when it’s fully charged it’s 60V.
@@TriggeredScream So, is this a 60v battery? If it's fully charged at 60v when measuring off load it' must therefore be a low 52v pack. A setting of 450 would therefore shut down the battery too soon. I would take the risk and set for 385 still. I assume this is a lithium battery.
Hi Mate, please I've got similar thing for Janobike t85 which is 60v, please what should i set it to? I would appreciate if you could help out on this.
Thanks man 👍
any settings here for battery level because battery gauge of my scooter is not accurate
Hello thank for you this video,,How do I reset my odometer?
Hi, unfortunately you cannot reset the odo, same as a car. The total accumulated mileage is stored in non-volatile memory on the the LCD control. You cannot change that if you want to zero the mileage. Much the same as a car. You can change the LCD control unit for a new one if you want 0 miles. How many miles have you done?! Do you mean the trip counter by any chance? You can reset this by pressing and holding the MODE button whilst the TRIP setting is displayed.
My scooter doesn’t go the speed limit on the third gear ? Any idea why
my darkknight power button won't turn on remote key chain beeps but it won't come on I was changing my settings to mph I think I dialed something wrong do you know if a setting could make the power button work
your reply got erased could you tell me again I think you said something about p3
Can you get more kph out of dragon v2 gtr flat out on flat ground is 23kph need more speed???
Battery capacity, motor power and controller won't allow more.
Setting for e-bike 24V?
Thank you very much.
Do you know what I can do to shut off the permanent lightning of the rear light
Unfortunately you cannot do that without physically disconnecting
@@marcusoroberts will have to disconnect then, thanks
Hi, the power on my scooter is set to 54 only, can i set it to max or 100? wont that damage the motor or should i just leave it at 54?
Hi, no this setting is intended to 'dial-back' power and usually scooters are shipped on that setting. If the settting has a maximum of 100, then it can be set to that. If you don't feel confident enough to ride on full power, perhaps your scooter has an 'eco' setting which helps to attenuate the power - and increase range.
Thank u from California
Cheers dude!
may i ask question
im from indonesia
my speedway turn off when i ride
the indicator battery is full
it so dificult to turn on
but if i hub to the charger
it can turn on
please give me a solution sir😊
Hi Rahmad, sorry I am not fully understanding the question; the scooter only works and powers the motor when it is connected to the charger. Is that correct? And if you disconnect the charger, the scooter will not work? Normally it is the controller, but this sounds different.
What setting for e-bike 24V 350 watt. 26.5
Hello Friend. great video.. I wanted to ask you something if you can help me. I have the display of my scooter that stopped working. But now when I want to find one, I see that there are many models that look alike on the outside. However, the AliExpress sellers told me when I sent them the photo of my controller, that they were not compatible... I imagine it was due to some software issue, because as I said, they are identical on the outside. round with the throttle trigger... like the tf-100 series. So I wanted to ask you, how can you know if it is compatible or not? What do I have to pay attention to? my controller is 18a.. 48v The problem is that I can't show you photos or anything here. Thank you.
Hi i have an 36 volts njax throttle can i adjust the voltage to 48 volts??
Hi Dennis, is your scooter 36v? It is a common OEM throttle. You can't set it higher than the battery voltage, you can set to 100% power and a power start. Also limit the voltage before the battery is damaged from under voltage. I'm not sure I understand, but I'll try to help....
is this for the maike kk4s scooter
Hi, it applies to any scooter with 10 settings as the throttle is generic.
My e10 scooters charging indicator is blinking without any reason how can I fix it
whats P2 for Janobike x10 2400 watt? 15 ? 16? 17?
hi, i bought a janobike dual 2000 w and I did a top speed of 50 km / h. then I found out that only the rear engine is running and the front engine does not start, does not respond at all to switching the red button (eco limits me to about 35 / h) in the setting also does not want P3 to let me go to 0, is it related? can you advise please
i just got the Quickwheel explorer 2x2700w and have the same problem, only the rear motor engages. yesterday the dualmotor button did let me engage the rear or the front motor only, but not both at the same time. now only the rear works and i did nothing since then.... ;)
I have 48 v scooter what should I have mine on
when you are in the main page when you hit the mode button there is a page which says instead of the speedometer it says CH and bellow it says time and 2:00 always what does that mean ?
If the LCD has that function, it means that after 2 minutes the scooter will time out and shut down. I've also seen scooters with this programmed to hours, so could also mean 2 hours!
Hi, thank you very much for the info, I got my 48V scooter today, I noticed that the Regenerative braking is not working, No matter the setting I choose, What I noticed is that when I slightly apply the brakes then an Exclamation sign appears. Surely it means a fault in the Regen Braking.
It's a "Shengte" Dual suspension similar to the Emove of Voromotors. Maybe they upgraded the controller because the original manual only describes 6 P's and the display actually have 10 P's. The P9 shows 0,1,2 levels so it corresponds to the manual you have in the description. I will send it back to warranty as the store provides 3 months
That's interesting to know, thanks for the share. So it's the usual OEM throttle/LCD you have with 10 settings and it conflicts with what's stated with the manual. The exclamation mark you describe does normally indicate an e-brake issue. I have also just encountered the same exclamation mark and am in the process of stripping it down. Again!
@@marcusoroberts Thanks for the reply, I will report back the answer from the store here at Chile. Meanwhile, trying to find info about the scooter I found this:
www.zjstcy.com/id-19.html
Is that one but 48V instead of 52V, the charger output is 54.6V 2A and the battery is 13Ah instead of the 23Ah stated in the page.
I think they sell older hardware with newer Controllers to try to keep low the prices and break the market or something... We will see.
How do I know when my scooter is actually gunna give out my scooter always surprises me but I get paranoid is there any eco mode is it better to go in single motor but I’ve heard daul balances out the battery anyone know anything?
Hi Quaid, I know that feeling. The only thing I can say is to treat the Mosfets as 'mechanical' switches working very hard in a daisy chain scenario. Heat is the enemy so keep them as cool as possible. The controllers are usually built cheap and manufacturers economise on heat sinking, so that is something you should consider modifying. In terms of riding, just don't go full power all the time. Share the load between both motors will make you use less throttle for sure, as will eco, as you correctly say. I mean, I have only had one controller go, so don't get too paranoid about it!
Hi, I have a question, is it going to somehow turn off the side led light? Or at least set one color? Thanks
Yes there is a vid on my Chan on this, I think under T112+ Dual. It's quite easy to work out, but I installed a waterproof toggle switch
But unfortunately it is not possible to change the side lights from the settings.
How do u go down on the modes not up
Nice
I have an issue where my scooter got stuck on cruise control. Then I felt something kind of snap or dislodge in the throttle lever. Now, the throttle doesnt work and the scooter only runs when I push the single or dual button. As well, there is on the screen a picture of something like circles or an "ooo=" symbol. Please, help...Lol, thank you
Cardwell, sorry to hear. There are 4 fault codes. An exclamation mark in a circle means electric brake fault. An 'M' means motor fault. A cylindrical thing that looks like a throttle grip with a couple wires going around it means throttle fault. A box shape means a controller problem. I'm afraid it's almost certainly the LCD throttle. They can't really be repaired. Best bet is to get one from Alibaba or AliExpress. Cheers.
Hello, good work.
I bought a scooter very similar to this. Brand new, turns on but doesnt accelerate at all. Do you know why this could be. Thanks
Throttle doesnt work
Is this for both motors or just the rear. It already sounds like a controller issue. What happens when you engage both motors?
@@marcusoroberts both mate, nothing happens
Trent it must be bad connection or a wire has detached. You might have to remove the footplate and really just inspect. Those Molex connectors are temperamental
When i got to this setting my speedmeter does not work anymore its always on 0 km/h now. How do i fix it
I am trying to find this out as well
I'm having the same problem, did you solve it ?
Hi sir ,, i own a kaabo 8 ,, is it working to change this LCD?
Hi, if it has 10 settings, it should be almost identical. Sometimes the settings are reserved or not used, but it should be the same for all 10 setting versions. Cheers.
As soon as I hit the throttle on the wide wheel, it will takeoff very fast and stay engaged. How do I take this function off and only go when I choose pulling the throttle more or less.
i put p0 in 25 is it ok?
Can I please confirm if you have the 60v 3200 watt chinese clone?
I think my motor poles is incorrect at 12 because the mph is about 10mph too slow. I increased the wheel diameter to compensate to 11.5 inches.
ThankYou great video
Thanks Chris, I have the 60v 2 X 2800w version. Hope that helps. Cheers
@@marcusoroberts you think trying to set poles from 12 to 15 will damage anything ? I can't get any info from the internet or the manufacturer. Thx for the reply it is appreciated.
@@docmortal yes I would have thought it should be set to 15 by default. It shouldn't do any damage. Most of the larger hub motors are set to 15. Safest thing is to stand the scooter on blocks and run off load, see if there are rumbles or jerky vibrations. Then take it outside, gently to start. Let me know how it goes. Good luck!
@@docmortal BTW I have my wheel diameter set to 10 and seems quite accurate
@@marcusoroberts Last question I promise lol
I was thinking of adding a steering damper. On the neck portion near the front wheel SHOULD be 2 set screws for removal to add the bracket. On my scooter no set screws. Do you have these set screws on your scooter?
Thanks!
Hello... I'm in the U.S. and have a nanrobot D4+ 2.0 and my throttle is malfunctioning part of the time, sometimes the throttle does nothing till I click the eco/dual mode buttons on and off sort of rapidly, and after riding for a bit I may be stopped or in the standing awaiting to proceed manner & the scooter will engage the throttle wide open completely on its own, yet this occurs totally at random. It's like being in a dunking booth at the fair... you know its gonna happen you just can't tell when or be prepared for it no matter how hard you try. Have you heard of these throttle symptoms before..? (Thank you for the videos by the way very informative.)
Hi Buxtro. First off, are there any orange warning symbols on the throttle display? There are 4 error condition codes. It might appear briefly whilst the 'drunk booth' thing happens. Does this happen only on rear drive or both? Any more info please. Cheers.
@@marcusoroberts no warning signs and it can happen in either dual or single mode Eco or non eco mode and I have the EBS disengaged at zero no kick-start no cruise control engaged voltage set at 43 and everything else is set to default. Have accumulated 539 miles total, I have driven through about 6 inches of water over 50 yards or so but did not start these symptoms till long afterwards and rinse it and wipe it down after every ride.
@@marcusoroberts and just to clarify I was referring to a dunking booth like where you sit on the bench and they throw the ball at the Target and when someone hits the the target the bench gives way dropping you in the water clarifying because you typed "drunk booth" which is the area where they put you in holding to you to sleep it off in the local jail big difference...
@@marcusoroberts matter of fact I'm going to take it for a spin right now and wait for the symptoms to occur and keep an eye on the throttle display I often keep it covered due to the blue light affecting my night vision lots of wildlife where I live in Virginia Beach also the six inches of water is due to Tidal flooding we get that alot in Virginia Beach so it was on asphalt it's just the entire Road was submerged with fresh water...
@@marcusoroberts just realizing if you're in the UK it's probably 1:30 a.m. whenever you get the moment let me know the time difference and I will respond respectively don't want to disrupt you're sleep or anyting.
How do you change the powers in the 3 modes? I have a 36v scooter and I am interested how can I change the speed and power limits in the 3 settings. The first lets me give with 15km/h the second 25km/h and the 3rd lets me go with 35km/h. Can I modify these settings? I would lower it to 15-20-30. I bought it for my wife and would be safer 😂
leave it on powermode2 or just dont go full speed?!?
What voltage it should have minimum to ride comparing to fully chrged?
A fully charged 60 V battery should read about 67 V when fully charged. It can be considered to be 'empty' at about 50 V, so it could be damaged if used below that threshold. For protecting the battery it's best to set the lower limit just above this, at 520 (52.0 V). Hope that helps.
@@marcusoroberts sure mate, thanks ;)
He my scooter is 60v and it's dying at like 64v
Hi, you might want to lower the setting of P1 Low Voltage Cut Off to around 520 (52v). What is it set to at the moment?
Hi there, I have an Emove cruiser I think the max speed is 25-26mph is there a way to get a higher top speed with these settings?
Hi sadly not possible. There is no room for a higher capacity battery, and even if there is room you'd have to upgrade the controller, then the motor. New scooter. You can't upgrade by parameter settings alone. Despite what others say, totally impossible.
Also, the T112 can do 40+ mph with dual motors, but weighs a lot more. But too heavy to carry around.
On the Emove Cruiser the P1 settings recommendation is 430 and I set it to 385 and before I was getting 24-26mph now it’s 27-30mph is that possible by changing that settings?
@@ushercozy sounds like the battery protection setting. You can lower it slightly at the compromise of the battery but the internal battery BMS will buffer issues
Marcus Roberts so should I leave it at 430 or at 385 ? Because the battery is a 52V 30AH
my display meter is fading out, some of the lines are not so clear. how to fix this?
I think you answered your own question, change the LCD throttle unit. No fix for that. Is it similar to the one on my vid?
Hiya nice content but i was wondering i have the laotie ES 18 60v 38 ah controllers 2x 2600 motors = 5600 total ,when fully charged it reads 67v what should i set the P1 setting much respect thank you in advance xD
Hiya. I should ideally be in the range of 430-530 for a 60v battery. The Ah of the controllers is irrelevant , just the voltage. Then it gives good balance between range and battery protection.
@@marcusoroberts so mine reads 50.5 i guess i can just leave it as is then ?
@@verbsy yeah that's fine. It'll give you more range. The last thing you want is to spend a huge amount on a new battery cos it's too low! Those batteries aren't designed to have the last bit of juice sucked out of them.
@@verbsy I mean you could decrease to 430 if you are using very long distance.
@@marcusoroberts thx Marcus ,so it would be safe to set to 43.0 with no issue ? i guess the discharge is from 67v right
How do u change the time?
The is no clock, only the time since you switched the scooter on.
Can you give some solution why my scooter does not go when i push the throtle?
Is the throttle display lit up and are there any amber warning codes? Have you confirmed that the battery is fully charged? Do the other parts of the electrical system work such as lights, horn etc?
Hello, nice video but on my e scooter there isnt a p8 option any help on how to remove?
Hi, thanks. If there is no P8 power setting on your LCD, it is likely to be hardwired to default setting at the factory. Usually most scooters I have seen are set to 100% anyway, but you won't see an option for that.
@@marcusoroberts so is there any way that i can make it go higher than 20km/h??
@@seimigraal7400 What scooter do you have? These settings relate to the scooters that will typically do 50+ kmh with no modification, such as the T112. There is no way in getting more speed without changing the battery, controller and motor which means a totally new scooter.
How about the CHA? What does it means?
CHA is the time to that the scooter has to automatically shut down because lack of any input or throttle. Normally not used. Usually just ignore it.
hi I have the kuggo m4 do you know the settings for this as I cant find any in English
Hi Richard, if you go into the settings menu and tell me how many options there are, I might help. Does the LCD display look like the ones from my other vids on the settings?
Thanks for getting back to me, its a tf-100 , its starts on p02 p03 p04 p06 p07 p09 p15 p16 p99 od0 im not sure if that's any good for you.
@@richardmonk8957 The settings always start on p0 or p1, but never have I heard them start on p02 go so far as p99! I'm not sure I can help. For the first time I'm struggling. These settings are hard coded and you can re-prog those via the USB on the back of the LCD - if you have the port.
Thats what I've seen on videos but this starts on p02 then after a few jumps to p99, I can find a video of the kuggo m4 settings but as its not in english I don't understand what each setting is doing but I know p02 is kmh into mph and p03 is the battery cut off thats is set to 48, i have a USB in the back but wouldn't know where to start with a re-prog
@@richardmonk8957 Perhaps it is hardwired and not able to be remapped. What is the voltage and Ah of the battery. It really depends, because if it is a street scooter it is restricted to around 15.5mph.
Hello sir what i will do if the display has a fault sign? Because my display has a fault sign and my scooter is not working anymore.
Hi John, is the orange fault sign in the shape of a box? What scooter do you have?
@@marcusoroberts i have blade 10.
the fault is throttle, i dont know how to fix it.
how can i send you the picture of my throttle display?
sorry this is not my account thats why the picture and name is differnt.
im just using this. but im john....
Marcus Roberts yes. Mine does. I can’t figure it out. I changed display and controller. Please help
Can you help me out?not sure how to change my seal up scooter to mph
Hi, on the 10 setting versions, usually changing P4 to 1 will make it MPH. On 18 setting versions it is P2. But remember on some scooters this setting is hardwired to KMH and can't be changed.
Once you set up regen, how do you use it?
It adds additional magnetic force to slow down and acts like a generator, feeds some of the power back to battery. It will cause the scooter to slow down more abruptly every time you release the throttle.
@@marcusoroberts I have a scooter with the same p settings but it doesn't feel like it's working.
@@southpole560 Sounds like there is a fault in the wiring. As long as the scooter works, the re gen braking is a bonus. Just check for loose connections.
@@southpole560 I personally either don't use very much, or only on a low setting for very hilly roads to save brake wear. I generally prefer to coast.
If you set p8 lower does the speed limit also get lower?
Algo para que la aceleración inicial sea más rápida ,más fuerte?
El p7 al 1 ,
Hi there! I have a T113 and don‘t know what setting 2 (P2) needs to be! I now have it on 13, but I don‘t know if that‘s right!
Hiya, if this has 10 settings (P0-P9) then P2 = 16 for both the T113 and T112 scooter. Hope that helps.
It's the magnetic pole in the motor setting
But it appears also to be fine set as '15'
Marcus Roberts ol great thanks! Never had it on 16 before! I will try it out! Because at the moment I sometimes have a problem with the scooter! Sometimes when I pull the throttle(in dual motor mode), one motor shuts done and doesn‘t work as it should! But thank you!
If you have set a totally wrong number, the motor will shudder and jerk a little. That is the Hall Effect sensor feedback saying something is wrong.
Hi I have a red light with an exclamation sing and scooter won't work?
Breaks maybe any help please?
Thanks....
Yes it means EBC fail (Electronic Break Control Fail). I have just upgraded my controller and have the same message. It is most certainly a wiring fault or loose connection correctly reported by the controller. I'm also working to repair mine and will report back. But your motors should still work. Do you have no power in both wheels?
@@marcusoroberts thanks man !!! Yes no power at all.... tomorrow I'll open and check the controller
@@marcusoroberts hi Marcus I checked the controller and changed new brake sensors but no luck the light is still on. BTW mine has only one rear motor.
@@DKLVE What is the make of your scooter?
@@marcusoroberts it's a generic one sold here in my country Chile. Well I had to disconnect both electric sensors and leave it just with the mechanical ones....works fine now .. thanks
I have a tifgalop thats p0-p9 how do i use cruse control it has the function for it i just can't find nothing on it
If you can't toggle that setting it's not available for you and that's governed by the controller mp ultimately, sorry
Hi could you help me please with an error 8 code on my walburg v2 hamburg scooter
Do u have the link to buy controller?
Hey Marcus, would you say the battery reading is correct on this scooter? Or would you go by your volt meter? As my battery today said it was 1 bar down yet my scooter died on me.. Stupid! Let me know please mate, thanks in advance
Yes the bargraph is not accurate at all. The numeric voltage display is far more accurate and I guess within +/- 5%
@@marcusoroberts thanks so much for your replies Marcus, I've been watching your videos just before I got my scooter, they were really helpful! Would love to see you post some more! Happy New Year btw :))
@@electchick_ Happy New Year to you too Jorgia. I will better videos soon, thanks.
Hey just another quick question, a couple of times my wheels have made like a 'crunching' sound, do you think it could be to do with the setting P2? Help.. My scooter is 60v 2000w dual, thank you
@@electchick_ motor pole pairs? P2 should be 15. That causes rumble and long term damage. Otherwise it might be bearing wear. Honestly bearing damage is very rare though.
What P-10 standing for on Electric Scooter???
This scooter only goes P0 to P9. If your scooter has more settings and goes higher than P10, it is usually PAS pedal assist mode and should be '2' meaning throttle start only.
@@marcusoroberts thanks for reply.
Hi marcus , can i ask you if you could help me with an error code 8 on my walburg urban e scooter the scooter was only used 5 short runs i disconected the throttle cable as it was twisted , when connected it came up with erros code 8 , not been able to get any help from manufacturers at all , where would i get a repair manual to find out a fix for it , Cheers m8
Unfortunately it sounds like the usual Mosfet failure in the controller.
My MoMAs s2 motor dont go when i push the Button and it have charging can it be problem with settings or is the problem with the motor. The scooter drive self when i tried it But when i push the button it not work
When you pull the throttle there's no power? Please give more detail. The motor rarely fails in any scooter.
Sorry I don't know that scooter; I only focus on the rapid dual motor scooters and Dualtrons.
I drive the scooter and Then i think i put in lighter and Then the scooter stooped
I cant take the scooter to a shop
Becouse the scooter is NPT allowed
How can i edit speed mode to be o maximum 24km/h ?
Hi Aly, I don't fully understand what you mean by setting a maximum speed of 24kmh Can you clarify for me please.
you can set P8 to 53 or 50 then you have your desired speed on the gear mode 3. otherwise set p8 to a 100% and change gear mode to 2 and you will have a speed of around 30Km/h. you can tweak P8 more. like 85 or something like that.
@@Drey_Toth Very good advice indeed. I just leave it to 100% but what you say is good. Then I have a the extra power on tap when needed. Cheers!
@@marcusoroberts He is probably in a country were that is the limit.
Mine only has upto p5 and I’m having the same problem. My gear 3 doesn’t go up to 45km as it says it should
my program is from P0to P6 only are they all same program
Hi, what scooter do you have? Does the throttle look similar to this one? It's possible that the programming mode is locked. I have not heard of only 7 modes. Hope I can help when you provide more info...
Cant see any thing besides Px
"I set it to xxx" where, how?
If you press and hold the power and mode buttons for about 3 seconds you enter the programming mode. I'm not sure if this is what you are asking. Please get back to me for more if needed. Cheers.
@@marcusoroberts Hi and thx for trying to answer. I only see you cycle through P0 to P9 without actual setting anything. So I dont know how to set/change a setting. I will get one on monday so hopefully I will get it right at some point :)
@@ibrenecario7357 Here, I will attach a full description roughly translated from Chinese. If you return in a few hours and look in my description of the above video, I'll 'try' to attach it on a shared drive. If after that you're still having probs, get back to me.
@@marcusoroberts Thank you very much. By the way, what scooter do you have?
@@ibrenecario7357 More than welcome. Hope you enjoy your new ride! I have 3: UberScoot Citi Hub 800 (road legal), Viper Dual 2000 and of course the T112 Dual 5600 which is absolutely savage - much too fast for its size.
Bro, i have speedway 4 mini 10.4 ah 36v.. please p1 ? 😭🙏
How to reset to the original speed?
Hi there. Sorry I don't fully understand. Do you mean the total mileage accumulated? Or calibrate the speed. Do you have any more detail, thanks.
@@marcusoroberts i mean,my real speed is 90Km and now i ride 47Km only,how to reset to 90km back?
Your scooter does 90kmh? What kind of scooter is this? It must be the fastest scooter in the world! I have dual 5600w and cannot quite achieve this speed. Please share a video of this Have you checked this on the GPS...
@@marcusoroberts not yet,cuz i dont really know.
When I’m on p5 mines on 1 and I want it on 0 does anyone no how to change that
mine is MR-100,dou hv this controler setting?
Hi, I don't know of MR-100 sorry. Who makes it?
@@marcusoroberts this escooter made in china,the controler model MR-100.its has P03,P06,P07,P09,P15,P16,P99 and 0d0 setting
@@varn4591sorry know that scooter
Hola a tod@s,
Tengo un display muy parecido al del vídeo, dónde podría ver para qué son cada uno de los parámetros (P0 al P9)
(Es de un patinete marca: e-town modelo: ETXZE7G)
Por diversas pruebas que hice, ya intuí para que son la mayoría, pero me gustaría corroborarlo con algo más fiable
Un saludo
What throttle is that?
Thanks
It's a standard programmable one that comes with most of the Chinese dual hub scooters now.
@@marcusorobertslike a Name or what they call it???
@@onetanggol9025 if you contact FLJ scooters, they will sell you one.
@@marcusoroberts thank you.
💯🚵🏀❤✈
@@onetanggol9025 cool let me know if you have problems.
Hi how do I get my scooter to go to 30 kilometres per hour ? It’s at 25 Rn do you know bro to change it. V
What scooter? What battery voltage? What is the model? Can't help you with no information
@@marcusoroberts ELECTRIC SCOOTER- DRAGON GT - 350 WATTS - 500W MAX
Unfortunately you won't get that speed ever from that scooter.
can I make my scooter faster just by using the settings? I’m at Gear 3 and it’s slow for my taste :( 20km/h
What scooter do you have? In gear 3, a 60v scooter should do approximately 35mph on average with the rear motor alone, and 45mph+ with dual mode. Tell me the scooter you have. It's possible with a change of controller and battery if you want to go faster....
Marcus Roberts
It’s a 52V20AH electric scooter, I don’t exactly know the brand of it, perhaps I could email you a photo of the scooter? It seems heavy duty however slow :/
@@TheHKZgamer Yes it should go faster than 20kmh as it's 52v for sure. Maybe it's restricted? In which case the limiter is governed within the LCD throttle unit.
@@TheHKZgamer share a pic. That would help mate. Cheers.
Marcus Roberts do you know how to remove it / disable it? + where could I share the photo
Hey man show me how to set the limited speed on p 08 a video please thanks
Press and hold power and mode button, use the mode button to toggle up to p8 then use the power or mode button to go up or down. Most scooters will already default to 100%
@@marcusoroberts not if yours automatically SKIPS OVER p8!! don't ask me why, but i have sets within the p1-p18 or whatever, that get skipped over so you can't get into that setting to change it... SO frustrating. oh yeah i have a joyor X5S any help would be awesome
@@straightciswhiteguy1584 Hi, so what is your question please?
@@marcusoroberts how do i access P08 if my little gizmo automatically skips over PO8 when i'm going through the settings. it's the most important one and on my scooter i cant' access it which means i can't change the speed faster than 15mph which makes it painfully slow. if you know the secret to get into PO8 i would be forever in debted to you
@@straightciswhiteguy1584 It's probably hard coded to not allow p8 to be changed. Unfortunately there is currently no way of changing the non-volatile memory in the controller to overcome this. Perhaps it is already set to 100% by default, but the power is not as much as you would like due to battery/controller/motor limitations...
For speed increase?
Upgraded controllers is the only way. Those standard MOSFETs can only work as hard as their rating. Push them further and they blow.
How do I make it go faster with just codes
Oh I wish this was possible, but it isn't sorry!
It asks me for a code, do you know what is it?
All ppl telling about not messing with motor poles setting but there are no Hall sensors in most controlers.
What's the model name of this scooter
FLJ T112 is the type. But the settings should work for most variants.