Great video ! No one has information! I called Suzuki I called Lowrance. They didn't know if this was possible. You did a great job with the video thank you so much!!
Thank ya sir. There’s a whole lot of non information out there for this nmea setup. That damned adapter cable got me. Bought the single engine adapter instead. A mistake made for my 250 2020. I learn that hard way every time.
Great video, I had it all wrong. I thought the hds would automatically read the engine. I was about to take it to the dealer to stnc them. Again thanks
What do you need to get fuel burn and fuel tank level? Thanks…great vid. I’m setting up a lowrance Fs9 elite on a brand new 220 excel Baypro w 200 suzuki
Great video I am wanting to set this up on my Suzuki DF70ATL2 outboard motor it’s a 2019 model. I am unsure of how to set up the interface cable to the engine and the adapter I have never been a mechanic.Any advise is greatly appreciated thank you.
Dear Sir, This is the only video that shows exatly how to connect..Thank you so much! I have got only one question.I have got a small boat where the nmea2000 end is really close to the engine.I would like to save cost if possible..Is it possible to connect the engine interface, directly to a SUZUKI DF25Atl or I also need an adapter cable. I mean if its so close can I connect the cable without the adapter? Is it only a task to lengthen the cable in case of longer distance, or possible to use if long enough the only interface cable with one end at the NMEA2000 and the other end at directly the engine connected? Thank you so much in advance!
great video. my interface cable has 3 connections. one for the NMEA the other two go on the engine. you only have one connection to the engine, where does the other connector go?
Hi there could you please help me now and tell me the part numbers of the interface cable and the connecting Cobo I’ve got a Suzuki 80 hp 2019 and I’m really struggle with finding the right equipment I did send another message from my friends phone because mine wasn’t working sorry for inconvenience having to messages with the same questions thank you
Hi, the suzuki engine interface is just to buy the cable connect to a nmea2000 line and connect and operate or do you need any more cables? I have a suzuki 115 hp 2018 greetings
@@RIVERCITYOUTDOORS where does the other end of the Suzuki interface plug into. There are 3 connectors one plugs into the nema 2000 one goes to the diagnostic port but where does the last one plug into
![[ВИДЕОУРОК] СЕТЬ NMEA 2000 на ЛОДКЕ. ЧТО ПОКАЖУТ LOWRANCE и GARMIN на лодке FISHPRO x7 и HONDA BF150](http://i.ytimg.com/vi/VpzB5zjePTQ/mqdefault.jpg)
![[ВИДЕОУРОК] СЕТЬ NMEA 2000 на ЛОДКЕ. ЧТО ПОКАЖУТ LOWRANCE и GARMIN на лодке FISHPRO x7 и HONDA BF150](/img/tr.png)
Thank you so much. Can’t believe there is nothing else online. You are the man!
Great Video, really informative and to the point. Thank you.
Great vid. This vid and one other vid are the ONLY vids explaining this! I like the color of that excel as well!
Thanks Sam
Great video ! No one has information! I called Suzuki I called Lowrance. They didn't know if this was possible. You did a great job with the video thank you so much!!
You must have spoken to some ignorant people because its literally a main feature of these units and they sell the nmea2000 adapter
Thank ya sir. There’s a whole lot of non information out there for this nmea setup. That damned adapter cable got me. Bought the single engine adapter instead. A mistake made for my 250 2020. I learn that hard way every time.
Cheers mate very helpful
Great video, I had it all wrong. I thought the hds would automatically read the engine. I was about to take it to the dealer to stnc them. Again thanks
What do you need to get fuel burn and fuel tank level? Thanks…great vid. I’m setting up a lowrance Fs9 elite on a brand new 220 excel Baypro w 200 suzuki
Great video I am wanting to set this up on my Suzuki DF70ATL2 outboard motor it’s a 2019 model. I am unsure of how to set up the interface cable to the engine and the adapter I have never been a mechanic.Any advise is greatly appreciated thank you.
Thanks for the video. Do you get trim position on your graph with this setup?
Thank you for sharing some good info!!! Do you happen to know if this is the correct adapter cable item number 990C0-88136 ?
Hi, can you help me with some guidance from where have you brought the interface cable and connector cable. I have a Suzuki 80 hp 2019 .thank you ☺️
Dear Sir, This is the only video that shows exatly how to connect..Thank you so much! I have got only one question.I have got a small boat where the nmea2000 end is really close to the engine.I would like to save cost if possible..Is it possible to connect the engine interface, directly to a SUZUKI DF25Atl or I also need an adapter cable. I mean if its so close can I connect the cable without the adapter? Is it only a task to lengthen the cable in case of longer distance, or possible to use if long enough the only interface cable with one end at the NMEA2000 and the other end at directly the engine connected?
Thank you so much in advance!
great video. my interface cable has 3 connections. one for the NMEA the other two go on the engine. you only have one connection to the engine, where does the other connector go?
Hi there could you please help me now and tell me the part numbers of the interface cable and the connecting Cobo I’ve got a Suzuki 80 hp 2019 and I’m really struggle with finding the right equipment I did send another message from my friends phone because mine wasn’t working sorry for inconvenience having to messages with the same questions thank you
Hi, the suzuki engine interface is just to buy the cable connect to a nmea2000 line and connect and operate or do you need any more cables? I have a suzuki 115 hp 2018 greetings
Adolfo Sanchez Yes you need a adapter cable. Here is the part#
990C0-88136
SMIS Adapter to SDS
@@RIVERCITYOUTDOORS where does the other end of the Suzuki interface plug into. There are 3 connectors one plugs into the nema 2000 one goes to the diagnostic port but where does the last one plug into
@@17ikester that is for trim Gauge up on the console but pretty sure you won't be able to trim motor on the side if you use that port
@@RIVERCITYOUTDOORS got it I appreciate the reply couldn’t fine anything on line except you video very helpful
Next time ask somebody to hold the camera!!!!
No one said you had to watch it. Next time figure it out yourself dick
@@RIVERCITYOUTDOORS no need to be rude. I wish I haven't seen your video! Dick yourself. Good day
@@koalajs wow way to come in a year later tough guy... 💪 😂
@@jasonhuggins8944 not the same person, ignorant twat !