Had to pause four minutes in and comment. Well done, love how you jump into specific detailed breakdown of the existing harness and it’s functionality. This helps so much given most vids are specific to the new mod or item installed, whereas I’m reverse engineering my own setup to do fresh rewire. Being able to confirm my ideas and understanding with your video is great. Thanks 🙏🏽
I just finished up redoing my 1994 wiring harness with the help of this video. Thank you for posting this. I’m down to Vehicle Speed Sensor to run my factory speedometer. I’m not using the 4L60E wanting to use the 10L90 Or 6R80. Either way I’m not seeing a straight forward solution for keeping the factory speedometer.
I found this video just in time I have a 90 SS454 I’m going to install a 4l80e transmission with a USShift controller and keeping the big block but using a Holley Sniper fuel injection setup for fuel and ignition this definitely gave me a direction to go excellent videos
The 88-94 obs main wiring bulkhead has teeth and GM monkey snot inside. I just heated it with a propane torch, pull it apart and remove all the wires. Then I die grind out all the teeth and monkey snot of bulkhead and reuse the wiring bulkhead to pass new wires from engine compartment to the cab.
I want to swap my 1190 C150 obs with a 5.3 with 4L60E trans, why don't you do a video #2 with the stand alone harness with all the connection to the obs wiring...
Hey I’m having some issues I have the blue wire coming out of my starter loom that’s supposed to be the knock sensor harness right And then I have a smaller grey wire with the same exact connector as the knock sensor Any clue what that might be? 1990 k1500 obs
Had to pause four minutes in and comment. Well done, love how you jump into specific detailed breakdown of the existing harness and it’s functionality. This helps so much given most vids are specific to the new mod or item installed, whereas I’m reverse engineering my own setup to do fresh rewire. Being able to confirm my ideas and understanding with your video is great. Thanks 🙏🏽
Excellent video... Finally a detailed explanation. Now if only a video detailing a GM 1996 and newer.
Thank you guys.
Ah the 96 and newer is terrible to do
@@swaptimeusa Can you please briefly explain why, I have a 96 Impala SS stripped down that I'd like to swap. TY
Do you sell the harness and pcm setups for gen V ??
@@izq4991 yes, Swaptimeusa.com
My truck is a 95, would this work
I just finished up redoing my 1994 wiring harness with the help of this video. Thank you for posting this.
I’m down to Vehicle Speed Sensor to run my factory speedometer.
I’m not using the 4L60E wanting to use the 10L90
Or 6R80. Either way I’m not seeing a straight forward solution for keeping the factory speedometer.
I found this video just in time I have a 90 SS454 I’m going to install a 4l80e transmission with a USShift controller and keeping the big block but using a Holley Sniper fuel injection setup for fuel and ignition this definitely gave me a direction to go excellent videos
The 88-94 obs main wiring bulkhead has teeth and GM monkey snot inside. I just heated it with a propane torch, pull it apart and remove all the wires. Then I die grind out all the teeth and monkey snot of bulkhead and reuse the wiring bulkhead to pass new wires from engine compartment to the cab.
I have a 94 regular cab with a 4.3 v6, I want to do a gen v l83 swap. Is there any difference I should know about as far as the v6 goes? Thanks
What about tuning? You guys do tuning on the 17 and up lt engines?
I want to swap my 1190 C150 obs with a 5.3 with 4L60E trans, why don't you do a video #2 with the stand alone harness with all the connection to the obs wiring...
Hey I’m having some issues
I have the blue wire coming out of my starter loom that’s supposed to be the knock sensor harness right
And then I have a smaller grey wire with the same exact connector as the knock sensor
Any clue what that might be?
1990 k1500 obs
Is this wiring the same for a 95 k1500 thanks
im thinking about getting a short box 2wd obs . might have to put a 5.3 in someday
How about all the a/c functions? Or they just need power from that big red wire?
Ac runs threw Mitches new harness I believe
What is the email to ask him questions about purchasing parts for a swap
Have to heat it up
Who else came back to find where the flush cuts go.. 🤚🤚