Possibly the Greatest Tenoning Jig Ever
Vložit
- čas přidán 25. 10. 2022
- Possibly the best table saw tenoning jig ever. With this simple yet clever jig, you can cut tenons of any angle, cut slots for picture frame splines, make low angle raised panel cuts, and more.
TOOLS USED IN THIS VIDEO:
Standard Matchfit Dovetail Clamps - amzn.to/3FzbV3t
Matchfit Dovetail Router Bit (1/2" Shank) - lddy.no/1cmae
Matchfit Dovetail Router Bit (1/4" Shank) - amzn.to/3S2ssQD
Matchfit Starter Pack - amzn.to/3DxG81I
My Dado Stack - lddy.no/qe5i
My Miter Gauge - amzn.to/3TkyIUi
CHECK OUT MY TAPER SLED VIDEO HERE - • Unlimited Possibilitie...
CHECK OUT MY WORKBENCH UPGRADES HERE - • Workbench Upgrades / G...
HOW TO MAKE A MITERED HALF LAP PICTURE FRAME - • How to Make a Mitered ...
Looking for DISCOUNTED HIGH-QUALITY PEC COMBINATION SQUARES, DOUBLE SIDED TAPE and overall great savings ALL THE TIME? Shop where I shop! lddy.no/go67
YOU CAN SAVE 10% ON STARBOND CA GLUES AND ACCELERATOR!
Use the code “INSPIRE10” at checkout! www.starbond.com
SAVE 10% ON OLIGHT FLASHLIGHTS, TACTICAL LIGHTS AND HEADLAMPS!
Use the code "INSPIRE10" at checkout! www.olightstore.com/?streamer...
BANGGOOD WOODWORKING TOOLS: www.banggood.com/marketing-Wo...
MY HAND TOOLS, POWER TOOLS, CAMERA GEAR AND MORE:
www.amazon.com/shop/inspirewo...
VISIT THE INSPIRE WOODCRAFT SHOP: inspirewoodcraft.com/product-...
Adjustable Box Joint Jig Plan: inspirewoodcraft.com/product/...
Multipurpose Shooting Board Plan: inspirewoodcraft.com/product/...
All Purpose Tapering Jig Plan: inspirewoodcraft.com/product/...
EMAIL: inspirewoodcraft@gmail.com
WEBSITE: www.inspirewoodcraft.com
PATREON: / inspirewoodcraft
INSTAGRAM: / inspirewoodcraft
If you appreciate this content and would like to help give back FREE OF CHARGE, simply give this video a “thumbs up”, leave a positive comment, subscribe to Inspire Woodcraft’s CZcams channel and SHARE THIS VIDEO with someone who you think would enjoy it. Some of the links that we’ve provided above are affiliate links. That means that when you make purchases through those links, we earn a small commission of the sale at no additional cost to you. While we do use affiliate links where we can, we only endorse products or services that we believe in. That commission is a big part of our income, which also goes back into making more videos, so by using the links you help support what we do and for that we are very grateful. - Jak na to + styl
![I'm fully satisfied with this VERTICAL HOLDING JIG that I use most frequently [woodworking]](http://i.ytimg.com/vi/xrT5hdw8i9I/mqdefault.jpg)
![I'm fully satisfied with this VERTICAL HOLDING JIG that I use most frequently [woodworking]](/img/tr.png)
One of the most appropriately named woodworking channels around!
100% agreed!
Right?! 💯 concur
holy crap best unspoken tip ever - reverse the mitre gauge for wide material on crosscuts ! needed this!!!
Thanks for sharing those tips and the make!
That's a very satisfying closing shot, the angled bridle joint sliding into place.
That is a superb design, as always you deliver , great job!👏👍😀
With a shop as small as mine, this will be a space saver. Thank you for sharing
Your jigs are awesome...thank you!
Yet another jig with multiple uses and simple to make ... I especially like that you've used parts of your other jig with this jig ... fantastic!
That is a great design. I've been looking at redoing my tenoning jig and I've found the design I'm going to use. Thank you!
Thank you. I picked up the Matchfit Starter pack. Looking forward to making use of it like your awesome jig!
Another impressive video, Jody! You have really been knocking them out of the park since returning form your extended hiatus! Keep 'em comin' brother!
Another home run!! Love your channel!
Looks like the next jig that I'll be building for my table saw. Thanks Jody~!
Outstanding. This will be the one. Thanks and really, nice job all around.
Jeeze what a simple design and so flexible. This will be made in my shop this weekend for sure. Many thanks!!
Great concept on the jig. Lots of maneuverability and options, love it! And the "you can make things without math" theme is wonderful, as always,🤣🤣 . Great video.
This is a great jig! I never thought of using a jig like this to make spline joints on picture frames and the like. You have come up with a way to make a tenoning jig much more versatile and quick to adjust to angles, etc. Thanks for sharing this idea.
Perhaps the greatest indeed! Keep 'em coming.
Good morning always good to wake up to see you have posted!! You make the best jigs hands down!!! Thanks for sharing
Those Microjig dovetail clamp systems are great. Wow, those were some tight angled saddle joints. Nice! It’s on my list o’ things to make this jig and to add dovetail grooves to my workbench.
I'm right there with the rest of the viewers. This is a great concept that you just brought to life.
Great way to set up for angles and being able to put in splines. Thank you for sharing it`s a great lesson learned.
Excellent idea! Thanks for sharing.
Well done. Like the dovetail clamps.👍👍Thank you for sharing. Have a great day and stay safe.🙂🙂
Beautiful! Thanks for sharing this.
This is a great jig! Any jig that has multiple purposes is a winner to me. Thank you for sharing! Take care and GOD BLESS 🙏!
Simple flexible and effective!! I’ve been planning to build a splint jig, this one looks great!! Also I like your comment on less stuff=more space
Simple, elegant and versatile. I'm going to make one, I do like the use of dovetail slots, got some spare 18mm MDF around too.
Great design
Brilliant as usual!
Great jig! Thanks for sharing 👍
This is great. Thanks for the inspiration.
Fantastic work
Great jig!
Really brilliant jig, dude! Fantastic work! 😃
Thanks a bunch for the tip!
Stay safe there with your family! 🖖😊
Another great knowledge bomb! Thanks as always
Wow, that bridle joint was awesome. There's usually a whole day doing that...
I haven't even watched all of this video yet but let me just say this. I subscribe to a lot of woodworking YT channels, and this is the only channel where when I see "The Greatest..'insert tip here' ever"...I actually believe it before I even click on it. And fyi, use the Paul Sellers "knife wall" for the shoulder lines and you wont need a backer to prevent tearout....
Great video brother
Excellent!
Smart and easy - one of those applies to me!
Wow! Nice!
Nice! Love how fast you dialed in the 45 deg. I have some ideas on incorporating parf guide dog holes to do what you just did. But I want to see if I can put the clamp handles on the other side of the board. Great video
Nice! Just nice.
Nice jig! I built a quick and dirty version to make some angled bridle joints, and screwed a toggle clamp into the backer piece so I didn’t have to deal with the clamps.
Nice, works better than my miter jig!
Great video. I especially appreciate how you refrain from always grabbing the tape measure (or other measuring device) to determine a needed dimension (e.g. the width of your saw fence) and then transferring that dimension to your work piece. As you have explained in other videos, this usually is easier and quicker and ends with a more accurate final result. Your videos have almost always provided some new information to me that has helped me in my work. Thank you.
Amen to those words!
@GF 937 That's awesome! And thank you for the kind words!
Yes, measure nunce, cut once. :)
Very cool…… I’m going to make this jig! The metal jigs you buy from Grizzly and Delta have limited range of adjustment across the table saw top whereas a table saw fence has tremendous range.
Sweet jig. I like- now to get that crappy bit loose from my router that has been in there for ten years...
Hi. Thanks for this vid.
How do you keep the piece from being too tight to slide on the fence? I used 1 strip of masking tape on the fence but it was too loose and too tight without it. I think it's the screws that pull it too tight and also why it throws me out of square. How do you do to keep it just tight enough?
@Alvaro Burbano It might depend on the material that you're using, but the screws shouldn't compress the material enough to make a significant difference. I don't like using the masking tape trick with stuff like this just for that reason. That being said, if it's too loose, you can just take it apart and trim down the top pieces one very small amount at a time until it fits.
Pertama kali lihat miter gauge dipakai terbalik.😮
Pura vida mi amigo great design I want to use one this in my shop.what are the name or brand of your clamps? Thanks pura vida guys
Thanks a ton again for your videos. I find your tips the most useful. Can I ask, what to do if the tall piece is out of square? It was square but when I put the screws it went out of square.
@Alvaro Burbano Could be a few different things. Like something as simple as the cuts not being close enough to 90 degrees. As long as it rides the fence smoothly though, you should be able to adjust the fence itself to 90 with the tenoning jig on it. Just don't forget to set it back when you're done!
Why have I never before seen someone use their miter gauge backwards?!? 🤯
Great jig! Any thoughts on how to adapt this for use with my Incra TS-LS fence? With the T shape of the fence, I can't slide the jig if there is a back side. Would it be stable enough without that?
@5055hunter I don't have experience with that setup, but I wouldn't think it would be stable enough, simply because of the height. If I'm not mistaken, that fence has accessory tracks on top though, right? Maybe you could incorporate those somehow.
@@InspireWoodcraft yes! forgot about that. Add a couple of t-bolts to the jig to give it stability. I think the height would still have to come down some, but might be doable.
What blade are you using to cut? Is it the flat top ripping blade?
@Rich H For the MDF I used a triple chip grind, 84-tooth Diablo blade. For the joinery I use a Forrest Woodworker II #1 Grind, which is a flat grind joinery blade. Interestingly enough I used the flat top grind for MDF yesterday and it worked great there as well.
That ended quickly...
How about making a push stick and using it! Bad example for any rookie out there !
I’m not even a minute into this and am watching you with your fingers mere inches away from that whirling blade w/ a GRRipper sitting right there in the camera front unused. What are you thinking, man? Seriously, use the safety tools you have, if for no other reason than to be a good role model for people watching this stuff. I know you’re good at this but accidents happen. That’s why they’re called accidents. Btw, I am a subscriber. That just freaked me out. Ok, back to your video. ✌️
@ms22401gal I use the GRRipper all the time. Generally speaking, table saw rip cut are perfectly acceptable and safe with your hands within four or so inches from the blade. Especially when working with a straight, flat, stable material such as MDF and using a riving knife. As for the cuts with the miter gauge, the GRRipper wouldn't have done me any good there as it can't be used in that situation. A good rule of thumb is anything outside of the throat plate on the fence side is safe, or the same distance on the opposite side, which I was on both accounts. Another good rule of thumb is that if you don't think it's safe for YOU to do, don't do it.
Not your fingers…not your problem.
@@jeffw8611 Disagree.
Mehaaa