Video není dostupné.
Omlouváme se.
Reviving the Power: Dewalt DCH273 Hammer Repair & Maintenance Guide
Vložit
- čas přidán 29. 03. 2023
- Welcome to our CZcams channel! Explore our comprehensive guide on maintaining and repairing the Dewalt DCH273 hammer drill. From basic upkeep to complete rebuilds, our tutorial covers it all. Learn to disassemble, diagnose, and troubleshoot issues with step-by-step instructions. Whether you're a pro or a DIY enthusiast, optimize your tool's performance by watching our must-see maintenance guide.
Subscribe for more power tool repair guides and don't forget to thumbs up and share if you find this helpful. Revive the power of your Dewalt DCH273 with our expert tips! Join us as we shine a light on service lights, blinking lights, and maintenance tips for Hilti tools. 🚀 #power #dewalt #hammerrepair #maintenanceguide #toolrepair #handyman #diy #tutorial #hammermaintenance
👍 Don't forget to like, share, and subscribe for more valuable content! Leave your comments below if you found this guide helpful: / @powertoolsrepair
✅ Stay Connected To Us.
👉 Instagram: / powertoolsrepairchannel
👉 Facebook: / powertoolsrepairyoutube
👉 Tiktok: www.tiktok.com...
=============================
✅ Recommended Playlists:
👉 Makita Repair:
/ watchv=p9my80wyope&lis...
👉 Dewalt Repair:
• Ultimate Guide: Cleani...
✅ Other Videos You Might Be Interested In Watching:
👉 Dewalt Drill chuck replacement:
• Dewalt Drill chuck rep...
👉 How to change melted Makita 18V:
• Step-by-Step Guide: Re...
👉 Milwaukee M12 battery not charging repair:
• Milwaukee M12 Battery ...
👉 How to repair Bosch GWS 20 230:
• Bosch GWS 20 230 Big A...
================================
✅ About Power Tools Repair:
This is where the Power Tools Repair Intro begins!
Power Tools Repair is your ultimate destination for everything DIY and power tools! If you're a fan of Makita, Dewalt, Hilti, Bosch, Milwaukee, Hitachi, and more.
You've come to the right place. Our channel is a haven for tool enthusiasts, DIYers, and professionals alike, offering a treasure trove of content dedicated to the world of power tools, repairs, and restoration.
If you want to send your power tool for repair please contact via email.
✅ Email: powertoolsrepairchannel@gmail.com
🔔 Subscribe to the channel: / @powertoolsrepair
#diy #toolrepair #powertools #repair #toolrestoration #tools #dewalt #handyman #dewaltdrill #dewaltpowertools #dewalttools #dewalttough #dewaltrepair #dewaltfix #flexvolt
=================================
Disclaimer: We do not accept any liability for any loss or damage incurred by you acting or not acting as a result of watching any of our publications. You acknowledge that you use the information we provide at your own risk. Do your research.
Copyright Notice: This video and our CZcams channel contain dialogue, music, and images that are the property of the Power Tools Repair. You are authorized to share the video link and channel and embed this video in your website or others as long as a link back to our CZcams channel is provided.
© Power Tools Repair
Hello.
That spring that goes on the rotating ball axis that keeps the ball seated on the rotating plate, what would be the part code?
I'm referring to the spring at the minute @14:14
By the way, the video is very good
hello, thank you. Part number 490286-00
Thank you for the video!
Is the ram supposed to be pushed into the piston that far?
I’m having trouble with my Dewalt dch273, when chipping/hammer mode when you release pressure the chisel pushes out to far and it sticks so it doesn’t hammer, so you have to put a lot of downward pressure on it to push it back into place so it starts hammering again. I just replaced the the ball, spring, washer, piston, ram, and o-ring, but it’s still doing it. It seems like it’s the beat piece that’s sticking, because I can push the beat piece back in with a screwdriver, but it could be something else slightly jamming. I have some videos on my CZcams channel showing the issue. Do you have any ideas?
Thank you again!
I think you need to try replacing hammer, don't forget to grease it - I usecMakita yeallow grease. From your videos tool looks like new, its not under warranty?
@@powertoolsrepair
Thank you!
Unfortunately it was bought about 4 years ago and it was only used 2 times in the first year. It looks different now, because it’s been used a lot in the past year. It’s had this problem since I first bought it. I thought it was normal until it became annoying to use and I figured something has to be wrong.
So you think I have to replace the whole front piece(spindle), part number N477771, or all the parts inside that spindle piece?
Thank you again.
My hammer had the clip #35 distorted and off the spindle. How do you finish the final assembly of the spindle so the spring is compressed enough to install the clip? The washer, Item 34 is too large for the clip to retain. Since the washer is the same one that was in the unit, I was wondering if the clip was supposed to retain it or go directly on the bearing. I would appreciate any assistance in this. A great instructive video.
I think clip must retain washer and I fix all parts in a vise to press spring and make assemble easy
I need to reassemble that as well, could you provide more details on how to compress it with a bench vise? Did you use a custom tool like a holow socket to push the retainer all the way in? A video about that would be cool 😅
@@tornecro I press one side with vise and gently hitting other side with hammer to get it pressed all tha way
Can you make a video disassembling of spindle. Will be great helpful.
I have this drill and it hammers but feels like it is not hammering as hard or fast as it did, think it might just need cleaning
It can be that its need to be cleaned,but change o-rings and grease, check motor if its good
My dch273 is horrorable knocking sound on hammering, what will be the problem??
Need new o-rings and grease
Thanks you very very much for helping and nice videos.
This one oring N114827. ??
@arifqureshi9928 part number 37, 41, 44 and grease
Thanks
Bonjour, ou à tu réussi à avoir les roulement s'il te plaît. Tu a un lien internet des pièces. En te remerciant.
I purchase them in retail store, you find them in eBay
Could you please mention what grease you used on the SDS?
I used Makita grease part number 181490-7
What grease can I use ?
I use Makita grease code 181490-7
My dewalt dch273 too noisly on hammer, what will be the problem??
Most of time its o-rings,hammer and grease need to be replaced
Thanks a lot
Is there a lot of broblems with this model? Seem to be in repair all the time🤔🤔
Not a lot problems, its very common model thats why they are more in repair because they are use offten. This model is good and durable
Where i will find that piece
If you need parts try to search for local Dewalt service parts dealer or ebay, amazon etc...