I have this hammer, i used it with long drill bits (maybe i stressed it too much) and now when i use the rotary drill function i can see the the tipping point of the drill bits swirling around. What do you think i need to replace, what can be broken? The hammer function works fine, but as a rotary drill (without hammering swtiched on) i can't make precision holes when the tipping point doesn't stay firm on his axis! Thanks you very much in advance for every suggestion and help!
@@riccardograsselli9465 I think the main tube is bent unfortunately when you buy the parts and fit them it wouldn't be worth doing. I would suggest buying the same model again and keeping the old one for parts or as a back up
Thank you for your comments and verbal support on every single thing that you did. Especially concerning the sheared crank assembly and proper push back action of piston when the right O-ring was asserted. The replacement items, lubrication links and transcript were also very helpful.
I really like this one doc!! Very detailed and helpful. I'm fairly confident that I can do this same repair after watching and learning from you!! Thanks again doc!!
Great job lad..the only thing I would comment on is when you are prying the hammer tube up and out of the case... Keep your hand away from the back end... I have had ones before that have broke the c clip holding the gear and spring on.. it can come out like a bullet... But that was well done and we'll explained... Take care my friend.
Use light grease inside the tube in the sliding parts Heavy grease on the cogs Ebay for the o.ring www.ebay.co.uk/itm/386435103102?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=ctxmdqtptf-&sssrc=4429486&ssuid=cjPn_ZfdQLW&var=&widget_ver=artemis&media=COPY
Very detailed video, thanks Doctor. Just wondering where can I buy a spare 3 pin connector at the bottom of the drill for D25303DH dust extractor? I have checked everywhere but can't find it.
Got the brushed version so while giving it a clean up i checked an seen someone's been in it and the grease looks green, not sure if it's the right stuff but the machine works fine only problem is hammer drill and hammer mode makes a really loud clacking when you pull the trigger more than half way.
@@doctorlefthandthread the insides seemed fine, nothing out of place from what i saw, didn't take the hammer assembly apart though so maybe its in there
Likely the washer down the tube on the striker number 37 or 41 on the parts diagram that's where the issue is www.partshopdirect.co.uk/dewalt-dch273-rotary-hammer-spare-parts-s15448/
To order Grease for servicing the hammer see link below
amzn.to/3JzRYdG
I have this hammer, i used it with long drill bits (maybe i stressed it too much) and now when i use the rotary drill function i can see the the tipping point of the drill bits swirling around. What do you think i need to replace, what can be broken? The hammer function works fine, but as a rotary drill (without hammering swtiched on) i can't make precision holes when the tipping point doesn't stay firm on his axis! Thanks you very much in advance for every suggestion and help!
@@riccardograsselli9465 I think the main tube is bent unfortunately when you buy the parts and fit them it wouldn't be worth doing. I would suggest buying the same model again and keeping the old one for parts or as a back up
Thanks very useful information. 👍
Thank you for your comments and verbal support on every single thing that you did. Especially concerning the sheared crank assembly and proper push back action of piston when the right O-ring was asserted. The replacement items, lubrication links and transcript were also very helpful.
Thank you for commenting it all helps
Cheers! 👍
Thank you sir
I really like this one doc!! Very detailed and helpful. I'm fairly confident that I can do this same repair after watching and learning from you!! Thanks again doc!!
Thank you Branden Hope you are healing well
Great. Very helpful video.
That was my intention to make a proper helpful video of this model thanks for your comment
It's always good, and doesn't hurt, to replace O rings, rusty nuts & bolts etc.
That O ring nearly always gives trouble it is usually sensible to replace it when you are in there
Good video Paul
Thanks Kevin it might help some man out
thank you so much
You are welcome
Great job lad..the only thing I would comment on is when you are prying the hammer tube up and out of the case... Keep your hand away from the back end... I have had ones before that have broke the c clip holding the gear and spring on.. it can come out like a bullet... But that was well done and we'll explained... Take care my friend.
Good man Darren thank you
Awesome video can I just use synthetic grease for everything and where would I order new o rings ?
Use light grease inside the tube in the sliding parts
Heavy grease on the cogs
Ebay for the o.ring
www.ebay.co.uk/itm/386435103102?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=ctxmdqtptf-&sssrc=4429486&ssuid=cjPn_ZfdQLW&var=&widget_ver=artemis&media=COPY
Very detailed video, thanks Doctor. Just wondering where can I buy a spare 3 pin connector at the bottom of the drill for D25303DH dust extractor? I have checked everywhere but can't find it.
I can't see a listing for it online
Got the brushed version so while giving it a clean up i checked an seen someone's been in it and the grease looks green, not sure if it's the right stuff but the machine works fine only problem is hammer drill and hammer mode makes a really loud clacking when you pull the trigger more than half way.
Is there anything broken in yours the brushed version has the same hammer mechanism?
@@doctorlefthandthread the insides seemed fine, nothing out of place from what i saw, didn't take the hammer assembly apart though so maybe its in there
Playlist
czcams.com/play/PLduybcJ2nSYXXBHkOIucDmbFs2GrrnwOm.html&si=RIXZdGfrt6-W8Um2
A large syringe with a little bit of tube on it would make a handy little grease gun
Big syringe is good for that job yes
Where are you based pal do u do repairs I've the same problem
I am Co Tyrone I do repairs for people that ask I still don't refuse much.
My dch273 making horrorable knocking sound on hammering, what will be the problem???
Likely the washer down the tube on the striker number 37 or 41 on the parts diagram that's where the issue is
www.partshopdirect.co.uk/dewalt-dch273-rotary-hammer-spare-parts-s15448/
Thanks a lot.
Can you use a beef and tomato pot noodle tub?????
Absolutely the parts will taste more of beef though but this will not adversely affect the performance of the drill
Beef and tomato would probably be better for milwaukee
And original curry for a Makita
Koka noodles for parkside 😂😂
Hi link to parkside repairs as promised czcams.com/video/PnJpKVJNhvY/video.html
Thanks Dave