brushed motor wont last long time, but like the simple build! If you want it to work, keep it simple, great engineer once said. water seal on motor shaft holding up well? computer fan blowing positive pressure into the pvc pipe may keep the water out?
Do you know what motor he used and where I could get one a bit larger like it? I'm gonna try to make this for a rowboat. I would like to get some good speed as well and any suggestions on motor size would be a huge help. I want to get good speed maybe 9-10 nots if possible. I don't know how to find the propeller either. Is this design going to last? what should I be watching to keep it in top condition? Any information would be much appreciated!! (:
Im going to make a very important suggestion. Use PVC glue, not that stuff you were using. Silicon sealant is needed as well. And while I'm at it, definitely a bigger prop
Actual pvc glue holds better than simple weather strip adhesive. BUT the problem using pvc glue is this--- what happens if you're out and need to make repairs? With weather strip adhesive you can pull it apart.
Yeah I would not be very efficient prop too small motor too small be okay for Putting around a small pond maybe let's just say I wouldn't lose sight of the dock
Maybe try using some rubber cement glue to glue the rubber seal to the motor and put grease inside the rubber piece so it stays still while the shaft spins freely
I dont mean to be off topic but does any of you know a tool to get back into an instagram account? I stupidly forgot my password. I appreciate any tricks you can give me!
Looks like it worked. Not sure if it's water proof enough, but if you keep it turned upside down when not in use to let any accumulated water drain out, it should be ok. My minn kota 40# leaked for years(damaged shaft keep eating seals) before corrosion finally killed it.
greta idea. i would use a brushles in runner motor that does not care if it gets wet. a firmer prop with metal spindle and a lipo battery of 5000 mah at 11.1 volts.
Thewater seal probably wont keep water out but thats okay because keep in mind people intentionally run these motors under water to break them in for use in an rc car. Great video!
Not as fast as a jetski. But hay i say that is really well made. The build was very well thought of. But you went lazy on the finishing part. As you only used wires to attach it to the boat. You could have made a better system for that.
I would like to know if I made a boat like the one you did with 12v engine if I put a brushless motor 1000kv battery 4s it will work or I should make changes
Shut the music OFF and do some talking in it's place. Also, play the sound track. I want to hear the machine running when you are working it. I want to hear you explaining it in progress. See this old house,
I mean you don't have to use the same components that I he used inside the video you can actually find like more powerful components that are actually use them both to increase the speed more it's my own opinion
That’s very creative on a budget type of rig. What size is that dc motor by the way? After this video I did look up on dc motors and I see they have other motors that are much more powerful in terms of torque and rpm. You should upgrade your version by putting quad motors not just that but a more powerful motor with a custom made 5 blade aluminum propeller. Have it into the water 6 to 8 inches down in the water. Swap the battery out to 24v. If u want to be more creative use solar charge and see if you can get that inflable to plane over 15miles per hour all electric. Super light and powerful.
It's half true title of the video so come with 2 comments: 1. Good video on how to make electric motor for boat 2. It not about make "Electric Boat" video... However you earn my "Like"
Verdammt coole Lösung und noch dazu fast Umsonst die Röhre mit Kleber & Bögen Kosten nicht mal 10€... der Motor und die Batterie natürlich je nach Leistung. Werd mir so ein Ding für mein BellyBoat bauen, allerdings 2 strahlig und mit Metall Schrauben. Das Plastik Ding überlebt bestimmt kein Tag, ein mal Grundkontakt dann war's das. Gerade für BellyBoate eine Spitzen Lösung weil man die Halterung angleichen kann wie man sie braucht und es das Ding kaum Gewicht hat!!! Gruß Marco
Ignore the other reply. Yes, some people who do cocaine do not trim their pinky finger nail, but in this case, this is a traditional thing, it doesn't have anything to do with cocaine.
It worked way better than I would have thought, trolling motors aren't made for speed, the only thing I would have done is make it have a reverse which is super easy with a DC motor, just simply have a switch to reverse the polarity
The money spent on the DRONE footage could have gotten you a real trolling motor. Great job but it was not rocket science idea better off making a hybrid from different trolling motor parts.
brushed motor wont last long time, but like the simple build! If you want it to work, keep it simple, great engineer once said. water seal on motor shaft holding up well? computer fan blowing positive pressure into the pvc pipe may keep the water out?
A brushless motor would be better I have a few of them and they actually run faster than the ones with brushes.
what you need to consider is the cavitation rpm for your propeller . faster may not be better @@mysticwolf2842
According to channels like this, if I just own a hot glue gun, I can send astronauts to space....
LOL...you are funny
Pretty much
The now politically incorrect a team used to do it🤣
If you own imagination! Skip games, social media and the couch!
🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣
I give it 5 STARS for simplicity and ingenuity.....
I would use a larger motor, prop, and battery......
Great video
Do you know what motor he used and where I could get one a bit larger like it?
I'm gonna try to make this for a rowboat. I would like to get some good speed as well and any suggestions on motor size would be a huge help. I want to get good speed maybe 9-10 nots if possible. I don't know how to find the propeller either. Is this design going to last? what should I be watching to keep it in top condition?
Any information would be much appreciated!! (:
you inspired me to made similar for my kayak! I'll use flexi shaft and motor will keep out of water! but idea is brilliant!
Im going to make a very important suggestion. Use PVC glue, not that stuff you were using. Silicon sealant is needed as well. And while I'm at it, definitely a bigger prop
Make one your self dip shit
ㅇㅅㅁㄹㄹ
Actual pvc glue holds better than simple weather strip adhesive. BUT the problem using pvc glue is this--- what happens if you're out and need to make repairs? With weather strip adhesive you can pull it apart.
Guy H. rB6
Yeah I would not be very efficient prop too small motor too small be okay for Putting around a small pond maybe let's just say I wouldn't lose sight of the dock
Parabéns amigo inventor,vc certamente seria um bom motivo para ser estudado pela NASA!
Super like!!
Tu sabes escribir😧😧😧😧😧😧😧😧😧😧😧😧😧😧😧😧😩😩😩
Great you made it and you sailed also that what i liked.
Thanks for sharing
Es dinero tirado, en cuanto se gaste (10 minutos) la goma que puso como sello de agua, le va agua al ruleman y al motor y adios....
Looks good in theory, but the shaft seal wont last long.
I will say about 10 minutes, before the water sneak in...
Maybe try using some rubber cement glue to glue the rubber seal to the motor and put grease inside the rubber piece so it stays still while the shaft spins freely
Oh, this is brilliant
I dont mean to be off topic but does any of you know a tool to get back into an instagram account?
I stupidly forgot my password. I appreciate any tricks you can give me!
@Forest Andres Instablaster ;)
The video is very good. Can you give me more specifications of the engine used !? Thank you!
IT WAS A 775 DC MOTOR.
Hi, nice work! where did you get the rubber shaft sealing?
Looks like it worked. Not sure if it's water proof enough, but if you keep it turned upside down when not in use to let any accumulated water drain out, it should be ok. My minn kota 40# leaked for years(damaged shaft keep eating seals) before corrosion finally killed it.
Fine design of boat and motor for calm days. You win the prize for lowest cost motor.
Freakin' genius. Love this video. Way to go man.
greta idea. i would use a brushles in runner motor that does not care if it gets wet. a firmer prop with metal spindle and a lipo battery of 5000 mah at 11.1 volts.
I am afraid. Dat rubber water seal which you used in the front is not going to hold.....
That was what I spotted. Can't be spinning a rubber gasket and expect it to stay waterproof for very long.
It's under slight pressure to keep it sealed and it will be lubricated and cooled by the water so it could last quite a long time.
+Harry
не продержится и минуты.
Это если не обращать внимания на то, что корпус двигателя установлен в пластиковую крышку не герметично.
вода опасна для меди?
what sealant do you recommend? i just need it for a project, thanks
wow
good work bro
beats the hell out of rowing all day! good job
Thewater seal probably wont keep water out but thats okay because keep in mind people intentionally run these motors under water to break them in for use in an rc car. Great video!
Not as fast as a jetski. But hay i say that is really well made.
The build was very well thought of. But you went lazy on the finishing part. As you only used wires to attach it to the boat. You could have made a better system for that.
what do you suggest doing for finishing it up? I liked the idea and also thought the button on the handle was lame. foot peddle of some sort maybe?
You need to glue inside those hexkey screws as they loosen very easily over time.
Nice work man. Hello from Turkey :D
A parts list sure would have been nice but still brilliant
How did the rubber seal work out? It looks like a design weakness to me.
Simple yet effective! But I would not wana sit in that tiny boat 👀
not bad considering its made out of cheap materials the speed is great I rate it 10/10
I would like to know if I made a boat like the one you did with 12v engine if I put a brushless motor 1000kv battery 4s it will work or I should make changes
cool vid but the motor wont last you covered the cooling holes and thermally sealed the motor
Shut the music OFF and do some talking in it's place. Also, play the sound track. I want to hear the machine running when you are working it. I want to hear you explaining it in progress. See this old house,
Microphonix Virtual Studio who cares what u want!!!!
The creators of this video is from Viet Nam, I believe they can't speak english very well for you haha
Nice video but it's NEVER A GOOD IDEA to stick your fingers into the solvent of a PVC weld. It introduces skin oils etc.
good job on the motor, but I'd like to see more about the boat!
Hi... that look easy and possible to anyone , top👌
thanks for sharing
can i have the specifications of the motor that you used? the voltage and the current? thank you
I think its better to immerse the motor with oil so no water can get in. It can also provide cooling property to motor without short circuit
..marine grease
but the speed is little slow
no shit sherlock
no shit sherlock
I mean you don't have to use the same components that I he used inside the video you can actually find like more powerful components that are actually use them both to increase the speed more it's my own opinion
Is it really waterproof?
Genial!! Es un motor de ventilador?
Nice I would put some grease in the rubber seal. Can you provide the seal and coupler source- thanks
Olá meu amigo!
Qual o nome desse conector da elici.?
Good nice
Hi, where did you get the piece attached to the end.
can you share the link for the small rubber bushing. thanks.. its hard to find in the market.
Nice now u just need a big bracket with quads and your deep sea fishing in your lake lol
That’s very creative on a budget type of rig. What size is that dc motor by the way? After this video I did look up on dc motors and I see they have other motors that are much more powerful in terms of torque and rpm. You should upgrade your version by putting quad motors not just that but a more powerful motor with a custom made 5 blade aluminum propeller. Have it into the water 6 to 8 inches down in the water. Swap the battery out to 24v. If u want to be more creative use solar charge and see if you can get that inflable to plane over 15miles per hour all electric. Super light and powerful.
excelent, you made a best word with this idea.
u should have used a bigger propeller
Redy Nebam no the propeller is very good because if he used bigger propeller the motor isnt so strong
i dont think the torque produced by the motor is strong enough to sustain a bigger propeller.
...anyway, the rig as is scoots that boat along pretty nicely.
you can add a solar panel so that you can have a roof also to protect you from heat while fishing
Hi guy
Where you buy your componements ?
Thank you
Did u use 300rpm electric motor sir? Pls reply
No, I believe he used a much higher RPM motor because there is no gearbox on his motor.
Very ingenious. Works pretty good
B cho m hỏi mua cao su chống ngấm nước ở shop nào vậy. Cám ơn B!
@1:30 What's the technical name for this magical device?
Ziad Jeeroburkhan That’s the rubber thingybopper that goes on before the brass doohickey
That's a part inside a DVD drive that absorbs the vibration when the disc is spinning.
A Gromit
where i can find this watter seal? or something similar? thx
用橡胶圈锁住轴心，增加摩擦力，会影响他的转速 ，
this is very possible, can you list the items used please...and where i can get them...
Muy buena la batidora. Gracias.
Very low tech, but efficient. At least you can use the paddle for backup just in case. Not bad.
Battery box, what he said and heat shrink wire connections.
Badly need this for thesis can i ask for the material that was used in the vid.
It's half true title of the video so come with 2 comments:
1. Good video on how to make electric motor for boat
2. It not about make "Electric Boat" video...
However you earn my "Like"
How did you get the Arial view at the end?
Which motor did u use? How many rpm it has? Thank you
Verdammt coole Lösung und noch dazu fast Umsonst die Röhre mit Kleber & Bögen Kosten nicht mal 10€... der Motor und die Batterie natürlich je nach Leistung.
Werd mir so ein Ding für mein BellyBoat bauen, allerdings 2 strahlig und mit Metall Schrauben. Das Plastik Ding überlebt bestimmt kein Tag, ein mal Grundkontakt dann war's das.
Gerade für BellyBoate eine Spitzen Lösung weil man die Halterung angleichen kann wie man sie braucht und es das Ding kaum Gewicht hat!!! Gruß Marco
Chạy 1 thời gian có bị vô nước ko vậy bạn.
One VC man making an electric boat used in guerillar war against in Vietnam.
U wot m8?
Nice video but where you get that rubber piece from? The one that goes over the motor shaft( spindle)
From where did u get the rubber oil seal for the motor?
This is the best thing I've seen in a long time 🤗👍
Hi, can you advise the model of the propeller that you use?
Great DIY
Clear example why you should avoid to use air fans as screw-propellers.
I built one with an old 6 v heater fan motor lasted long on 12 v.
How??
Maravilloso !!!
where u get all these lil parts at?
What is the rubber piece used as a shaft seal?
Классный мотор получился !!!))))
Good work!
No lube on the seal, it will leak, but before that the motor will overheat with rated load.
Why is your pinki finger nail so long
coke finger
Ignore the other reply. Yes, some people who do cocaine do not trim their pinky finger nail, but in this case, this is a traditional thing, it doesn't have anything to do with cocaine.
BaileyTheGamer it's for cleaning inner ear
I'm legit curious as well. I just assumed he liked cocaine... not judging either way. lol
So you don’t say it but don’t tell when you see his damn finger nail in video, I’m half way threw and haven’t seen it yet
🖕🏻😠🖕🏻
I'm looking for ideas for any better shaft seal designs. Anyone?
It worked way better than I would have thought, trolling motors aren't made for speed, the only thing I would have done is make it have a reverse which is super easy with a DC motor, just simply have a switch to reverse the polarity
Nice but.... Water will get in the motor very fast...
good work
can u give me motor Specifications
Nice Video
whats the referenceof motor? its great! and batery what you use?
So from today, the fishermen do not want Minn Kota anymore ...
... We want the man in the green shirt!
Costs just as much as a used one
Мотор должен охлаждаться, а то сгорит за час))) За изобретения+55 Лайк!!!
Уплотнительная резинка на вале будет пропускать воду.
Est ce que c est adaptable sur un float tube ?
Where can we buy the rubber and connector to propeller??
Yeah, but where do you get the parts at?
Pouvez-vous donner le nom et les références des pièces utiliser Merci . Can you give the name and references of the parts use Thank you
when the boat floats on the water, then the video plays in fast mode
The money spent on the DRONE footage could have gotten you a real trolling motor. Great job but it was not rocket science idea better off making a hybrid from different trolling motor parts.
What's with the coke pinky? If you use threaded fittings you could do repairs/replacements wihtout having to rebuild the whole thing.
Good work ! But very slow. Maybe it's
low voltage?
6:09 his face 😂
WHOW..very good
excellent - where did propellor come from?
A fan
Lots of friction on that seal. Back to the drawing board... good vid anyway