After 20 minutes of going through these steps, I found I needed to press the button on my garage door opener head twice (once long to get a solid blue LED) and once quickly to blink purple. Only after this was the final step possible. Hope this helps for others also struggling!
Perfect instructions - I tried everything, Genie manual, Toyota owners manual, numerous forums - nothing worked. Followed this exactly and was up and running in less than a couple minutes. Well done.
Thank you. This video is much better than the one on the Home Lnk/Ford site. After 2 frustrating days, 30 plus minute attempts, I was finally able to complete programing my 23 Ford Edge.
When I looked up this video I was in customers garage delivered their car (Lexus driver here) lady asked I fi can help her w the process. I followed official Lexus video with no success, then I called my bud who owns a garage door repair business, and told him I have trouble programming their opener to "car mirror " remote buttons, as soon as I named Genie brand he said : good luck the worse garage door opener to program pain in the ass, sometimes its a matter of a distance and it must be not to far and not too close and tell em to just buy a decent garage opener ....lol.. thanks for the video, spent 40 minutes in a bit garage w no luck. I had a feeling that if I was to reset their remote and then program both of succeed. But I wasn't about to spend another 40+minutes there... Anyway to all you hitting dislike here : get a new garage door opener system! Lol
Thanks so much for this! I have a 2014 Ram and I couldn't get it programmed using the instructions that came with my new Genie. I realized that my issue was that I was not pressing the "program" button as outlined in the second half of this video. Note that Homelink started working for me after making 2 more presses of the homelink button (it did not need the third that is outlined in the video). Two long presses (1 second each) did the job.
This worked for my 2022 Ford F150 tremor. I had the genie remote with only 1 button. Thank you so much! I also was trying to program with my truck fully on. I should have realized to put my truck in accessory mode by hitting the start button without holding the brake. Thank you again!
Works with Genie StealthDrive Connect Model 7155-TKV. Make sure after you trigger the remote to Red... press and hold that same button 10 seconds to see the red/green LED on before holding the button in the car.
I followed the instruction and I was able to pair my Subaru Outback Homelink with the Genie garage door opener in my new home on the first try in 2 minutes. Thank you for posting this video.
I have the model 1028..... could never get my homelink in my Ram or Jeep or honda systems to work.... and after 3 years of using the stupid remote I finally got it to program from watching this video..... 3:48 is what I needed on how to program my system.... thanks !!!
Very glad to hear that this video helped you Jon. Anytime you need any assistance with your garage door opener, feel free to visit us here, or by calling us at 1-866-599-4995.
Thank you very much for the video. Nothing else I found worked, but this enabled me to get my wife's HomeLink working. It is good to watch all the steps before you start, or you will be running back and forth doing steps over again :). Also, once setup is completed, take your Genie remote out of programming mode again by repeating the steps for "preparing your remote for programming" that starts at 2:46. This gets your Genie remote back to green lights when you press the button. This security feature on the remote should probably be secured again after you've set up your HomeLink.
A couple of notes: 1) you don't need to hold for 10 seconds garage remote, just press and hold both simultaneously 2) keep remote very close (1 - 3 inches per my user's manual) to the mirror 3) once you turned on programming mode on the opener press and hold desired button on the mirror for 3 seconds(again per my BMW manual) with those little tweaks it finally worked for me
I had trouble programming my homelink with my new genie(model #3055) garage door opener. My issues was my led shop lights were blocking the signal. Turned them off and followed the recommended program directions and in ten minutes my issue was solved!
Yes LED lighting can cause radio frequency interference with a garage door openers signal. I am glad to hear you figured out that was the cause and are now working :) let us know if you need anything else.
If anyone else is having problems with a Genie opener (rolling code) and setting the Homelink in a 2016 Ram 2500 the truck actually had to be on and running before it would work. I tried multiple times with the key in the on position and not running with no luck. I did the same procedure found in this video but with the truck running and it worked the first time.
Unreal... Two weeks ago I bought a 2017 Ford Fusion. I drove it home and in 15 seconds had the Homelink connected to my 25 year old Genie garage door opener. I had a brand new garage door and Genie opener installed today and just about blew a gasket because neither of my Ford cars that have Homelink buttons would work with the new opener. All I had to do before was hold the remote next to the Homelink button and hold the buttons at the same time. Why are there now 15 steps to make this work, including getting a ladder and pushing buttons on the actual opener? Why is this so complicated 25 years later? Sheesh!!
If you have additional issues or "its just not working for you", try this after I experienced an issue of a lighting induced corruption or loss of codes in 1 of 2 identical Genie Belt Drive units. 1.) clear all button assignments on the individual remote fobs (instructions on the Genie website). Do a "Divorce Clear😂 - their term not mine!) by going into program mode and then holding both the + & - buttons at the same time. Now restart the Homelink programing process with the correct remote fob in each car followed but the "rolling code" procedure at the opener head. Best of Luck. There's an hour I'm not getting back but what a new skill. Maybe I should advertise and pair the neighborhood.
Awesome video I almost had a coronary trying to program my 2005 Lincoln town car as soon as I put this video on did it exactly as the video tells you to do it and it worked perfectly one try thank you very much
it will work with software version 2.0.3. mine did. make sure you clear out any codes already programmed into the home link first. also, it is best that your car is running (according to tech support). That is what I did and it now works...
My 2008 S500 would NOT take the code from a Genie Excellerator II "fob" (as pictured in this video) - software version 2.0.5. My son-in-law had one with Software 2.0.6, and THAT was accepted by my Mercedes' Homelink!
Can confirm a 2016 Chevy Tahoe will NOT work with 2.0.3. Had to go buy a new $30 remote (v 2.0.7) and it took the programming in about 3 seconds. I now keep it in a drawer for reprogramming in case I have to pull the battery and it gets lost.
I could not program my Homelink buttons in my 2018 Suburban with my small 3 button remote like shown in the video. Fortunately I remembered I had another style of remote in the drawer, generic version. I programmed, one of those buttons and then used that to program first to the car, which produced the fast flashing LED for the first time, then I did the Program button the Opener, followed by the double-press and then on the 3rd press it worked!!! Took me a good 45 minutes to work it out :/
It is a possibility that your three button may have an older software version (mentioned in the video), very glad to hear that you got it working, reach out with any questions
The instructions are confusing. It breaks down like this: Homelink needs to copy the handhelds code so it can masquerade as the handheld remote. Then you program the homelink to your door just like you would program a handheld remote. Here are the steps: Erase homelink in vehicle first by holding outside buttons for 20 seconds. Copy handheld remote code to homelink by holding handheld remote button until red and green lights light up. Release handheld button and press twice, light will be red. Hold homelink button until it starts blinking slowly then hold handheld button along with homelink for 20 second and release both. Now your homelink sends the same codes as your handheld and you can proceed to program it to your door. Now go to your garage door opener and press the square button for 3 seconds. Go to homelink and press desired opener button twice. Garage door should now respond to homelink
Do both the remote and homelink work in tandem after this process, or does the door opener only work with homelink? Thank you for your breakdown. What I’m wondering is if a rolling code (I’m assuming it uses a rolling code) needs to be transmitted and programmed on the remote from the opener, then transmit and program the rolling code from the remote to the home link, then transmit and program the rolling code obtained via the remote from homelink to the door opener while the door opener is in program mode. I’m assuming that the remote and home link will both work if successfully completed, within the specified timeframe and if not completed in that timeframe, the rolling code will change and the process will need to be started over. Do you have any insight? I’ll be attempting this setup soon.
I just programmed my homelink and found that the instructions in the Genie manual and the vehicle are confusing. I was able to do it with the new 7055 Genie. 1. In the vehicle - clear all the prior codes - Press the two outside homelink buttons at the same time and hold for 20 to 25 seconds, you know they are clear because it will fast flash. 2. In the vehicle - hold the desired vehicle homelink button and the garage door remote opener button both at the same time for about 5 seconds, you will know it linked because it will fast flash. 3. On the garage door opener itself (in the garage) - there is a button labeled SET, push it for exactly two seconds, it will color change from green to blue on the dot and purple flashing on the bar. 4. In the vehicle - press the programmed button for exactly two seconds, then again for two seconds, and then press it once for about a second. The garage door will open or close. The button is now programmed. The opener will have a green light again.
So annoying that it was a comment that held the secret! I really wish folks could take the time to explain to people what they are doing - before they tell them how to do it. In this case - these instructions can be summarized as: 1) Copy your good remote's *certificate* into the new remote.. 2) Pair the new remote with your garage door opener. I'd completed step 1 many times successfully - without realizing there was a second step. Had they mentioned this in a clear and short fashion before getting into the weeds, I bet a lot more people would be using this.
This is incomplete. What you have to do I found, is program your car first with the remote, then go to the Genie and press the learn button, then go back to your car and press the programmed button on your car twice. Viola! It works.
I chose model 3120 and it took me here, which has nothing to do with my model. The written instructions are not helping at all. We have 2 cars that have always used Homelink and we cannot get this new opener to program. And of course, try calling the 800#. You will never get through. I am really sorry we didn’t spend more on a better Liftmaster.
I programmed the 1st button of my remote to my Homelink using this method. However, the 3rd button on my remote (which is programmed for my community gate via the internal dip switches) cannot be put into "program" mode (where both red and green LEDs turn on). Instead, when the 3rd button is pressed, the red LED just flashes rapidly indefinitely no matter how long it is held down. I called support and no one seems to know about this issue. Any help?
Hi We would need to confirm the model of remote, the Genie Master remote sounds like the remote you have. If the 3rd button is programmed to a gate opener with switches, then you wouldn't need to flip from red to green, that is for Intellicode 1 and intellicode 2 technology. What are you trying to reprogram the 3rd button to? HomeLink as well?
There are some different things that could be causing the red LED light. If this is a new installation, the limits need set before programming the remotes. If it is already set, please contact Genie customer service at 1-800-354-3643 for assistance.
Hi Bill - If you need any assistance with programming we are happy to help. You can reach out to our customer service at 1-800-354-3643 for assistance.
Are you talking about the keypad? Please use the keypad video for reprgoramming, this video is for remote and homelink. If you need help contact us at 1-800-354-3643
Hi, If you would like to send us a direct message here, on anyone of our Social Media platforms, or our live chat on our website, we would be more than happy to assist you. overheaddoor.custhelp.com/app/home
Hi Nath, It would depend on your model number. If you have an operator with a learn code button, you would press and hold the learn code button until the led next to it quits flashing. (then you would need to reprogram everything back in). If you have an operator with a PRO/SET button you would 1. Press and hold the program button until the round LED turns blue, then release. 2. Press and hold the Up(+) Down (-) buttons at the same time, until the both LEDs flash blue and go OFF.Then you will need to proceed with programming. Here is the link to programming this remote: czcams.com/video/Yx--M-tvqtg/video.html
So you have to have one of the remotes for the genie garage you can't just use the normal program button on the actual garage door opener. Seems really redundant and annoying.
You do have to have a Genie remote to program your HomeLink. The first step is training the HomeLink to know what brand, and technology garage door opener, it is being programmed into.
Hi Rangel, Some vehicles have additional/special programming. We can walk you through the programming if you are in need of further assistance. 1-800-354-3643.
2022 silverado will not progam to this opener. I have spent 2 days trying every way under the sun. The rolling code method doesn't work. Brand new truck and 1 year old garage door opener shouldn't be this fucking hard.
Sorry to hear of the trouble with programming your vehicle. We would be happy to help you resolve this. Please contact Genie customer support at 1-800-354-3643 for assistance.
@@johnstuart3851 I apologize for the hold time you experienced. If you would like to email your contact information to reviews@geniecompany.com I can have someone reach out to you.
Only 5 steps and combinations?? You should have at least added a step where the user has to spin clockwise in circles three times while depressing all buttons. Your engineers need to get it together!!
We would be happy to help you resolve any issues you are having programming your remote. Please contact Genie customer support at 1-800-354-3643 for assistance.
I agree that the instructions are confusing.Maybe you need to watch this 50 times.The online chat is even worst.They send you a link then they disappear.I should have chosen a better brand.THAT'S how disgusted I am.
Good God this is the most confusing video I've ever seen. Is this showing me how to program my Genie remote, or my vehicle? If I can use a Genie remote button with a red light (which I assume means it hasn't been assigned yet), how does my vehicle get programmed with the correct unit? Feedback for Genie: Just put a "pairing" button on the opener; push the pairing button, then press and hold whatever it is you want to pair (vehicle button, Genie remote button) and you're done. None of this Clearing, red light/green light, hold for 10 seconds nonsense
Hi - Since HomeLink makes the in car vehicle system, you have to train the system to know you are going to use it with a "Genie' branded garage door opener. So yes you are training the system, and then programming the system into our unit. If you need assistance contact us at 1-800-354-3643 we will walk you through the programming
Been trying for a half an hour - it’s a good thing I don’t have any place to go at the moment.
i realize Im quite off topic but does anyone know a good website to stream newly released series online ?
It’s all a mystery…. Yippee
Shit doesn’t work
Did you fix it? Also are you using a different remote or a genie remote? I’m thinking it only works on specific remote?
After 20 minutes of going through these steps, I found I needed to press the button on my garage door opener head twice (once long to get a solid blue LED) and once quickly to blink purple. Only after this was the final step possible. Hope this helps for others also struggling!
Thank you thank you. This did it finally. Thank you kind sir.
Thank you! This was the step that was holding me up and not letting me finish this frustrating process 🙏
Yes! After 3 nights after the 2 year old went to bed, this is the secret! Thank you!
This worked for me also. Thank you so much!
I don’t know who you are but you are my new hero. Thank you!!! I was about to give up.
Perfect instructions - I tried everything, Genie manual, Toyota owners manual, numerous forums - nothing worked. Followed this exactly and was up and running in less than a couple minutes.
Well done.
Thank you glad it worked!
Thank you. This video is much better than the one on the Home Lnk/Ford site. After 2 frustrating days, 30 plus minute attempts, I was finally able to complete programing my 23 Ford Edge.
When I looked up this video I was in customers garage delivered their car (Lexus driver here) lady asked I fi can help her w the process. I followed official Lexus video with no success, then I called my bud who owns a garage door repair business, and told him I have trouble programming their opener to "car mirror " remote buttons, as soon as I named Genie brand he said : good luck the worse garage door opener to program pain in the ass, sometimes its a matter of a distance and it must be not to far and not too close and tell em to just buy a decent garage opener ....lol.. thanks for the video, spent 40 minutes in a bit garage w no luck. I had a feeling that if I was to reset their remote and then program both of succeed. But I wasn't about to spend another 40+minutes there... Anyway to all you hitting dislike here : get a new garage door opener system! Lol
Thanks so much for this! I have a 2014 Ram and I couldn't get it programmed using the instructions that came with my new Genie. I realized that my issue was that I was not pressing the "program" button as outlined in the second half of this video. Note that Homelink started working for me after making 2 more presses of the homelink button (it did not need the third that is outlined in the video). Two long presses (1 second each) did the job.
This worked for my 2022 Ford F150 tremor. I had the genie remote with only 1 button. Thank you so much! I also was trying to program with my truck fully on. I should have realized to put my truck in accessory mode by hitting the start button without holding the brake. Thank you again!
Works with Genie StealthDrive Connect Model 7155-TKV. Make sure after you trigger the remote to Red... press and hold that same button 10 seconds to see the red/green LED on before holding the button in the car.
I followed the instruction and I was able to pair my Subaru Outback Homelink with the Genie garage door opener in my new home on the first try in 2 minutes. Thank you for posting this video.
I have the model 1028..... could never get my homelink in my Ram or Jeep or honda systems to work.... and after 3 years of using the stupid remote I finally got it to program from watching this video..... 3:48 is what I needed on how to program my system.... thanks !!!
Very glad to hear that this video helped you Jon. Anytime you need any assistance with your garage door opener, feel free to visit us here, or by calling us at 1-866-599-4995.
Thank you very much for the video. Nothing else I found worked, but this enabled me to get my wife's HomeLink working. It is good to watch all the steps before you start, or you will be running back and forth doing steps over again :). Also, once setup is completed, take your Genie remote out of programming mode again by repeating the steps for "preparing your remote for programming" that starts at 2:46. This gets your Genie remote back to green lights when you press the button. This security feature on the remote should probably be secured again after you've set up your HomeLink.
A couple of notes:
1) you don't need to hold for 10 seconds garage remote, just press and hold both simultaneously
2) keep remote very close (1 - 3 inches per my user's manual) to the mirror
3) once you turned on programming mode on the opener press and hold desired button on the mirror for 3 seconds(again per my BMW manual)
with those little tweaks it finally worked for me
Wow the only directions on youtube that worked for me, thanks. Works well.
Yay. Confirming this worked perfectly with a Genie Excelerator II. None of the other tutorials were working. Gotta go to the source sometimes.
Was having trouble but after watching this video my problem was solved. Thanks
awesome, wasn't in the instructions, couldn't have got this working without these steps. Thanks.
Thank you! No way I was going to figure this one out in my own. Other videos/instructions do no cover the specifics of these newer genie models.
The 3rd method worked for me even though I have a new 3 button remote. Thanks!!
Took three presses of the button but worked like a charm.
I had trouble programming my homelink with my new genie(model #3055) garage door opener. My issues was my led shop lights were blocking the signal. Turned them off and followed the recommended program directions and in ten minutes my issue was solved!
Yes LED lighting can cause radio frequency interference with a garage door openers signal. I am glad to hear you figured out that was the cause and are now working :) let us know if you need anything else.
You are correct sir! Thanks!
Thank you so much
Your video shows crystal clear instructions
Great job
You're welcome
Very clear and simple, got my garage program to my car. Thank you very much.
If anyone else is having problems with a Genie opener (rolling code) and setting the
Homelink in a 2016 Ram 2500 the truck actually had to be on and running
before it would work. I tried multiple times with the key in the on
position and not running with no luck. I did the same procedure found
in this video but with the truck running and it worked the first time.
Yahtzee. Holy shit, did the same. Ignition on but not running 20X (22 Ram)
I can’t even tell you how many thing a I tried to get it to work and nothing prevailed. Thank you so much for this video!
Unreal... Two weeks ago I bought a 2017 Ford Fusion. I drove it home and in 15 seconds had the Homelink connected to my 25 year old Genie garage door opener. I had a brand new garage door and Genie opener installed today and just about blew a gasket because neither of my Ford cars that have Homelink buttons would work with the new opener. All I had to do before was hold the remote next to the Homelink button and hold the buttons at the same time. Why are there now 15 steps to make this work, including getting a ladder and pushing buttons on the actual opener? Why is this so complicated 25 years later? Sheesh!!
Rolling codes to prevent robbery.
@@zdwade So folks just break into the car to open the garage - EZPZ.
To prevent others from opening. Also it would get mixed up with neighbors remotes. That’s why.
This whole time I had the wrong software version in the remote. I was ready to go thermonuclear on this thing. Saved my bacon.
Let us know f you need anything further!
This is the one. Very well explained and steps
You saved me. Thank you. 2021 Mustang Mach E and 2021 Jeep Gladiator.
If you have additional issues or "its just not working for you", try this after I experienced an issue of a lighting induced corruption or loss of codes in 1 of 2 identical Genie Belt Drive units. 1.) clear all button assignments on the individual remote fobs (instructions on the Genie website). Do a "Divorce Clear😂 - their term not mine!) by going into program mode and then holding both the + & - buttons at the same time. Now restart the Homelink programing process with the correct remote fob in each car followed but the "rolling code" procedure at the opener head. Best of Luck. There's an hour I'm not getting back but what a new skill. Maybe I should advertise and pair the neighborhood.
Awesome video I almost had a coronary trying to program my 2005 Lincoln town car as soon as I put this video on did it exactly as the video tells you to do it and it worked perfectly one try thank you very much
it will work with software version 2.0.3. mine did. make sure you clear out any codes already programmed into the home link first. also, it is best that your car is running (according to tech support). That is what I did and it now works...
My 2008 S500 would NOT take the code from a Genie Excellerator II "fob" (as pictured in this video) - software version 2.0.5. My son-in-law had one with Software 2.0.6, and THAT was accepted by my Mercedes' Homelink!
Why r u doing this to me
Can confirm a 2016 Chevy Tahoe will NOT work with 2.0.3. Had to go buy a new $30 remote (v 2.0.7) and it took the programming in about 3 seconds. I now keep it in a drawer for reprogramming in case I have to pull the battery and it gets lost.
I could not program my Homelink buttons in my 2018 Suburban with my small 3 button remote like shown in the video. Fortunately I remembered I had another style of remote in the drawer, generic version. I programmed, one of those buttons and then used that to program first to the car, which produced the fast flashing LED for the first time, then I did the Program button the Opener, followed by the double-press and then on the 3rd press it worked!!! Took me a good 45 minutes to work it out :/
It is a possibility that your three button may have an older software version (mentioned in the video), very glad to hear that you got it working, reach out with any questions
Worked perfectly for Genie Model 1028. Thanks a million!!
Thank you! This made it much easier to program three cars.
Better than Ford's instructions, worked on first try.
The instructions are confusing. It breaks down like this:
Homelink needs to copy the handhelds code so it can masquerade as the handheld remote. Then you program the homelink to your door just like you would program a handheld remote.
Here are the steps:
Erase homelink in vehicle first by holding outside buttons for 20 seconds.
Copy handheld remote code to homelink by holding handheld remote button until red and green lights light up. Release handheld button and press twice, light will be red.
Hold homelink button until it starts blinking slowly then hold handheld button along with homelink for 20 second and release both. Now your homelink sends the same codes as your handheld and you can proceed to program it to your door.
Now go to your garage door opener and press the square button for 3 seconds.
Go to homelink and press desired opener button twice.
Garage door should now respond to homelink
It wasn't really that confusing. You literally just reiterated the video.
Thanks! That video sucks. Genie sucks. Making this a 20 step process... Lame.
@@RobMarques I found it much clearer but glad to have both.
This comment was more useful than the video.
Do both the remote and homelink work in tandem after this process, or does the door opener only work with homelink?
Thank you for your breakdown. What I’m wondering is if a rolling code (I’m assuming it uses a rolling code) needs to be transmitted and programmed on the remote from the opener, then transmit and program the rolling code from the remote to the home link, then transmit and program the rolling code obtained via the remote from homelink to the door opener while the door opener is in program mode. I’m assuming that the remote and home link will both work if successfully completed, within the specified timeframe and if not completed in that timeframe, the rolling code will change and the process will need to be started over. Do you have any insight? I’ll be attempting this setup soon.
Thank you Slightly different instructions than jeep but it WORKED!! First time.
This is the video that has the right way! Thank you.
Worked great, simple straight forward instructions. 2020 Hyundai Kona Ultimate, Genie Machforce 2HP
Worked perfectly with Genie model 2028 and Subaru Impreza 2015 homelink auto dimming mirror. :)
Thanks for the video, I got my Model S homelink programmed and it’s super cool.
Thank you ! Worked flawlessly. First try
I just programmed my homelink and found that the instructions in the Genie manual and the vehicle are confusing. I was able to do it with the new 7055 Genie.
1. In the vehicle - clear all the prior codes - Press the two outside homelink buttons at the same time and hold for 20 to 25 seconds, you know they are clear because it will fast flash.
2. In the vehicle - hold the desired vehicle homelink button and the garage door remote opener button both at the same time for about 5 seconds, you will know it linked because it will fast flash.
3. On the garage door opener itself (in the garage) - there is a button labeled SET, push it for exactly two seconds, it will color change from green to blue on the dot and purple flashing on the bar.
4. In the vehicle - press the programmed button for exactly two seconds, then again for two seconds, and then press it once for about a second. The garage door will open or close.
The button is now programmed. The opener will have a green light again.
So annoying that it was a comment that held the secret!
I really wish folks could take the time to explain to people what they are doing - before they tell them how to do it.
In this case - these instructions can be summarized as:
1) Copy your good remote's *certificate* into the new remote..
2) Pair the new remote with your garage door opener.
I'd completed step 1 many times successfully - without realizing there was a second step. Had they mentioned this in a clear and short fashion before getting into the weeds, I bet a lot more people would be using this.
Try mine , works Great.
Lear System in ‘10 Chevy Tahoe. Was able to program left button, same steps won’t allow center button to open garage door.
Thank you! This was so helpful amazing!
Thanks Adam Corolla
Print the instructions ON THE UNIT! Thank you. 😊
This is tricky.
This is incomplete. What you have to do I found, is program your car first with the remote, then go to the Genie and press the learn button, then go back to your car and press the programmed button on your car twice. Viola! It works.
I could swear that is exactly how it was as I watched this video. Did you see something different?
You are correct sir!
That's what the damn video shows to do.
This was helpful I got it programed!
Thanks working great
I wish I'd never bought a Genie opener..... cannot get the car programmed.... What a pain in the ass!!!!!!!!
Call us at 1-800-354-3643 we can walk you through it.
Awesome I got it done
People go to the next video immediately. This one is way to complicated. Next few I looked at work perfectly.
How can I configure it with my car if I don't have the remote control?
You cannot program the Homelink In-Vehicle remote system without having a working remote for your garage door opener.
That couldn’t be anymore confusing....
Thanks a lot. Easy to follow. It works.
It's not working for me bmw I have the 2028 model.
Will my remaining home link buttons still be able to work with Chamberlain or Craftsman?
I chose model 3120 and it took me here, which has nothing to do with my model. The written instructions are not helping at all. We have 2 cars that have always used Homelink and we cannot get this new opener to program. And of course, try calling the 800#. You will never get through. I am really sorry we didn’t spend more on a better Liftmaster.
thank you!
Anyone know a trick with 2015 ford escape I've been doing it and everything matches up with what he says but it's not working
I programmed the 1st button of my remote to my Homelink using this method. However, the 3rd button on my remote (which is programmed for my community gate via the internal dip switches) cannot be put into "program" mode (where both red and green LEDs turn on). Instead, when the 3rd button is pressed, the red LED just flashes rapidly indefinitely no matter how long it is held down. I called support and no one seems to know about this issue. Any help?
Hi We would need to confirm the model of remote, the Genie Master remote sounds like the remote you have. If the 3rd button is programmed to a gate opener with switches, then you wouldn't need to flip from red to green, that is for Intellicode 1 and intellicode 2 technology. What are you trying to reprogram the 3rd button to? HomeLink as well?
@@GenieCompany it's a GM3T. Yes, trying to program that third button to Homelink. Have tried dozens of times, it won't work.
It took several tries and a lot of persistence to program a 2015 Audi Q5
On my opener the light flashes purple but after about 20 seconds It turns red
There are some different things that could be causing the red LED light. If this is a new installation, the limits need set before programming the remotes. If it is already set, please contact Genie customer service at 1-800-354-3643 for assistance.
WOW that is complicated. Yeesh.
Hi Bill - If you need any assistance with programming we are happy to help. You can reach out to our customer service at 1-800-354-3643 for assistance.
The keyboard is not working when I type the number the garage won’t open
Are you talking about the keypad? Please use the keypad video for reprgoramming, this video is for remote and homelink. If you need help contact us at 1-800-354-3643
What should I do if I only have the button, no remote?
You would need to purchase a compatible remote for both, , program the remote, and use it to train homelink to the unit.
So i have a remote with software 2.0.3 , I have tried everything. Do i have to purchase a new remote to program my 2018 chevy
HI Frank - Call us, we will walk you through it. 1-800-354-3643
calling on a Tues @ 11an pst
"45 min hold time"
screw you guys
Hi,
If you would like to send us a direct message here, on anyone of our Social Media platforms, or our live chat on our website, we would be more than happy to assist you.
overheaddoor.custhelp.com/app/home
Did not work with single button remote with 1028 toyota 2020 Home link
Please reach out to us at 1-800-354-3643 and we can walk you through it.
This has been an absolute nightmare ... geez
We'd love to help you, call us at 1-800-354-3643.
@@GenieCompany 2 hour hold time
Will home link work with a Genie model 3060m/l?
How do you Erase & Reprogram this tiny wireless remote ?
Hi Nath, It would depend on your model number. If you have an operator with a learn code button, you would press and hold the learn code button until the led next to it quits flashing. (then you would need to reprogram everything back in). If you have an operator with a PRO/SET button you would 1. Press and hold the program button until the round LED turns blue,
then release. 2. Press and hold the Up(+) Down (-) buttons at the same time, until the both LEDs flash blue and go OFF.Then you will need to proceed with programming. Here is the link to programming this remote: czcams.com/video/Yx--M-tvqtg/video.html
So you have to have one of the remotes for the genie garage you can't just use the normal program button on the actual garage door opener. Seems really redundant and annoying.
You do have to have a Genie remote to program your HomeLink. The first step is training the HomeLink to know what brand, and technology garage door opener, it is being programmed into.
Mr Rogers?
Didn't work , check the manual 7055
Cant get it to work. Ffs shouldn't need a NASA engineer to program a garage remote.
This doesn’t work with a 1055 and a 2019 Nissan Rogue.
Hi Chris! It should, please contact Genie customer service at 1-800-354-3643 for assistance.
My model is 2028 and your tutorial for synching my remote and car to the device is not working!!!! Please post up an appropriate tutorial !
My Lexus is300 won't connect :(
Hi Rangel,
Some vehicles have additional/special programming. We can walk you through the programming if you are in need of further assistance. 1-800-354-3643.
I have the exact same remote shown and it doesn't work. Even the Acura dealer can't get it to sync. What a pain in the ass
Cleveland from Family Guy?
? Nope lol
These steps do not work on genie 2028 model
Call us at 1-800-354-3643 and we can walk you through the steps.
After doing all this, sell your first born child, THEN press the button.....
and do the Hokey Pokey.
This didn’t work. This really is a horrible process especially when the app goes down.
2022 silverado will not progam to this opener. I have spent 2 days trying every way under the sun. The rolling code method doesn't work. Brand new truck and 1 year old garage door opener shouldn't be this fucking hard.
Sorry to hear of the trouble with programming your vehicle. We would be happy to help you resolve this. Please contact Genie customer support at 1-800-354-3643 for assistance.
@@GenieCompany With an estimated 40-minute wait on hold. What a shitshow.
@@johnstuart3851 I apologize for the hold time you experienced. If you would like to email your contact information to reviews@geniecompany.com I can have someone reach out to you.
This is a confusing
Only 5 steps and combinations?? You should have at least added a step where the user has to spin clockwise in circles three times while depressing all buttons. Your engineers need to get it together!!
This process is stupidly complex. I suggest reading lots of comments first because the video doesn't make it simpler.
We would be happy to help you resolve any issues you are having programming your remote. Please contact Genie customer support at 1-800-354-3643 for assistance.
I agree that the instructions are confusing.Maybe you need to watch this 50 times.The online chat is even worst.They send you a link then they disappear.I should have chosen a better brand.THAT'S how disgusted I am.
Don’t work
Good God this is the most confusing video I've ever seen. Is this showing me how to program my Genie remote, or my vehicle? If I can use a Genie remote button with a red light (which I assume means it hasn't been assigned yet), how does my vehicle get programmed with the correct unit?
Feedback for Genie: Just put a "pairing" button on the opener; push the pairing button, then press and hold whatever it is you want to pair (vehicle button, Genie remote button) and you're done. None of this Clearing, red light/green light, hold for 10 seconds nonsense
Hi - Since HomeLink makes the in car vehicle system, you have to train the system to know you are going to use it with a "Genie' branded garage door opener. So yes you are training the system, and then programming the system into our unit. If you need assistance contact us at 1-800-354-3643 we will walk you through the programming
WTF
Total BS doesn't work worth damn
We would be happy to walk you through the programming, please call us at 1-800-354-3643.
This is bullshyttt... should have stuck with a craftsman! 🤬
Instruct sucks
How the fuck in 2024 this an 80 step procedure that never worked. This should be a two step process. This opener running n dos 3?