How To Remove Crash Data GM Airbag Module Reset.

How To Remove Crash Data GM Airbag Module Reset. 2010 and newer GM vehicles. GM Airbag Module SDM VIN Write Crash or Internal Fault Hard Code.
In this video i show you how to write new vin in the sdm airbag module or clear crash or internal malfunction fault code. I show step by step instructions what tools needed for this job and how to do it on or off the car. GMLAN connection how to.
Chevy black box also known as SDM. GM Airbag Module SDM VIN Write Crash or Internal Fault Hard Code same black SDM box ( airbag control module ) is located in Chevrolet ( chevy ), Cadillac, Buick, GMC. Same Black SDM airbag module is found in 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020 cars, Trucks and SUVs.
If you dont have the tools here is a link where you can get this service done karmanauto.com...
#Vehix411 #CrashData #AirbagModule
What is airbag Module? What tools to clear crash data? How to clear crash data?

[@phillipspeegle7663]

Good to see not just a awesome mechanic but also using some electronic troubleshooting skills as well 👍

[@SALMANDER33]

Even after clearing any idea why dash light is still illuminate and may require srs scanner to reset ?

[@ivangarcia9318]

Where can I get one of those pin out break out box?
Thanks in advance

[@manuelvera8321]

Hello how are you, I have seen your video and it is very good, I have a problem in a 2010 buick module, but with my car prog it does not read it, see in the video that you use a box with k line, or can bus, you can give me the information where you sell it or if you have them for sale please I need one thanks for your attention

[@RuvimAbaras]

Thank you

[@josuehernandez-pg8dv]

Hello Dan , we're can I buy a breakout box like yours? Thanks

[@vehix411]

This one I make my self

[@dionisabreu9840]

How do i doi it through the obd port? I have it and the computer still in the car

[@tahergharbia2605]

Witch type of power supply you have ? Can I connect it direct without power supply?

[@omegay32se47]

Woo very good thank you

[@albertorangel2940]

Hi would you be able to reset my module? It's for a 18 spark? Please let me know

[@772777777777777]

How do you read gm sealed srs modules ie 2011 gmc 1500 truck

[@danieljimmydominguez1939]

donde conecto el pin 1 del obd2? gracias

[@Madafakris]

If you do it straight to the OBDII the process will be the same? Meaning, you have to use Carprog and do it the same way you do in this video?

[@edgarasededed6624]

did you try obd?

[@772777777777777]

please explain what in you breakout box you say its serial data port....please explain

[@772777777777777]

the break board your using is simply a external 12v power supply? required for srs , your using a1 multi adapter with straight threw connection to SDM /SRS module
as seen below correct?
OBDII pin1 GMLAN in A1 MULTI adapter------------------>>>> to pin 15 on SDM/ SRS module
OBDII pins 4,5 GND--------------------------------------------------->>>>to pin 19 on SDM /SRS module
OBDII pin 16 +12V----------------------------------------------------->>>> to pin 9 and pin 17 SDM /SRS module

[@RangeK1D]

Hey I have the same module. Roof airbags went off (passenger + driver). Will a OBD2 clear the codes or are they hard coded and need carprog?

[@alanleon6124]

Do you have a link or where i can buy the carprog?

[@radekradecki3187]

Hello its nessesery when air bags was exploid ?

[@vehix411]

Necessary on most makes and models

[@IYT865]

What is name of this programmer?

[@claudionanico9463]

Bom dia vc tem para vender

[@Tulitaratch]

Must be a way to do it without sending it out .

[@nihilisticpunk24]

It’s even worse than that. Contacted these dudes and they are saying this very SAME EXACT module can’t be programmed unless on car, yet this dude is showing them doing it on bench. Just BS. Scamming ass company…

[@canakbas3783]

thank u for sharing... carprog is original or clone?

[@vehix411]

original

[@arekw4339]

Hello Mate, Very good video. I have similar airbag module 13578320 and 13503645. Cant communicate via carprog on bench. I'm getting message" not response from ECU". I have connected via a1 multi same to pin1 obd and power supply with current 160mA. Can you help me?

[@elwooddean187]

hi i need some help can you email me please [e-mail] thanks

[@erickmarquez3365]

To fancy

[@davebrown4699]

I'm getting code U1016 is this my problem?

[@randybryant8087]

So you say it can be reset using just the vehicles obd2?

[@juanportillo2201]

Hi would this process erase B0052(deployment commanded) code?

[@vehix411]

You have to remove and clear that crash code off the car if you don’t that’s tools www.Karmanauto.com

[@alexk77ae]

Can you make me a breakout box? I will pay

[@edgarasededed6624]

Did you managed to read it ?

[@edgarasededed6624]

Я сейчас не могу найти виход