Video není dostupné.
Omlouváme se.
Vizio TV IR Sensor - Remote Control Won't Work - 3637-0022-0189 Replacement Tutorial
Vložit
- čas přidán 20. 04. 2017
- How to fix your Vizio IR Sensor
CLICK HERE for replacement parts: www.shopjimmy.com/catalogsearc...
TV Models:
Jvc
JLE32BC3001
JLE47BC3500
JLE47BC3001
JLE42BC3500
JLE42BC3001
JLE37BC3001
Vizio
M470SV LAUKJYAM
M420SV M3D651SV
M3D650SV LAEAMEAN
E3D470VX LATKJZEN
E3D470VX LAUKJZAM
E3D470VX LAQKJZEN
E3D420VX LAQKJXEN
E3D420VX LAQKJXAM
E3D420VX LATKJXEN
E3D420VX LAUKJXAM
E3D320VX LAUKJRAM
E3D320VX LAQKJRDN
M550SV LAUPKAAM
M550SV LAQPKAAM
Try all repairs and troubleshooting at your own risk.
In this video we will show how to replace the components in this Vizio IR sensor, component replacement kit.
We have already removed the board from the back of the TV.
I will not start by adding a little bit of solder to these three points on the board.
Flip the board over and turn the IR sensor up, so that you can hold it with one hand.
Run the iron back and forth over the points to warm them up and help remove the IC.
As the points are heated, the IC should fall out of the back side.
Use the iron and solder wick to clean the remaining solder off of the pads.
Insert the IC legs through the holes on the board. Line up the IC and bend it at the appropriate spot.
Add a little bit of solder to the iron and then begin to solder the legs on the IC.
After you have finished soldering, trim the legs.
Clean up the pads with some isopropyl alcohol and a brush.
Next, we will replace the resistor on the board.
I am using a hot-air tool, but you can use a soldering iron if you do not have a hot air tool.
I will begin by heating up the resistor and then lift it from the board with my tweezers,
Add a little bit of solder paste to the pads.
Set the replacement resistor on the pads.
Begin to heat the component until the solder paste melts and then properly align the resistor in the correct position.
Clean up the area with the isopropyl alcohol and a brush.
There you have it, we shown how to replace the two components in this Vizio IR sensor, component repair kit.
TV Repair Made Easy™
© 2017 ShopJimmy.com, LLC.
Very clear, great instructions. Thanks so much!
Hi, why you need to change the small resistor together with the onboard sensor IC
Hi I have a question my philips tv model 32HFL5860D/27 doesn't turn on it just keeps blinking a orange red color what should I do
Put a brand new IR Sensor in the TV, and it's not responding still. the remote seems to be fine, could it be the IR is defective?
does anyone that's completed this fix by chance know value of the smd resistor at RR1?
How do you know which resistor to fix ? There a few that look the same.
Can you share the values of the resistor and a part number for the ir sensor?
70 years old,,hands shake like a vibrator.this isn't a fix that I'm going to do!!
dude - spend $20 and get yourself some clamps or a vise or something to hold the piece while you work it..
..and while you're at it, buy a solder sucker!! It's a wonder you didn't wreck those lands! EDIT: This was the worst technique I've ever seen.
Not a very good job on the surface mounted resistor. Blind man could see that!