Video

Do this thing got and air filter or is it just a air vent/port

I’m fixing up one of these myself anyway I could connect with you? My shut off valve is leaking just wondering how you hooked yours up? Parts are not available.

Where can you get pars for these? Looking for fuel valve and gas cap that doesn’t leak (open close vent cap)

Is the mixture knob the idle pin for the carb? My engine seems to bog out at idle unless I give it throttle. I’m guessing it’s my idle pin

It did help me , but at the same time you need to know there are two sizes of bushing, I ordered both but the beefier one came first and my brother & I had to pound it from underneath to get it to dislodge fron the frame. I wish it came out the way yours did. We used the one we had but needed to go to Ace hdwe to get a 20 threaded nylok nut to stop from it coming loose while riding because the thicker bushing left fewer threads to fasten to end of shaft and used blue thread lok to help insure. it woul not come loose. All in all Thanks for the video 5 stars buddy.

do you guys know what engine you used?

Impact is your friend

What ratio should i mix the coolant at? Would only be summer use but dont want to ho straight water.

Have to manually unlatch it from underneath

I have one that the trim stays locked

Just wondering why not clean the old one sure there's nothing wrong with it .

I got the same exact one I’ve had if for 21yrs and runs really good. The weed less prop chews through everything. Just picked up a 74 for $25 going to try to get that running worst case I’ll have spare parts for the one I already have

an absolute beauty, look after her !!!

I know some people disagree, but, you can use an impact driver to remove the flywheel (on the center bolt of the puller.) Some are easy to remove, some not. Same with most magnetos and flywheels on these engies, motorcycles, atv's, dirtbikes, etc.

So that's all salt water if you're on the ocean?.. going right into the cylinder?

Thank you. Off to check mine...

Can you make a video on how to run it after you change your spark plugs

Thanks guys. This was an easy task that I had no idea on how to do. Now I do!!!

Cool video! I just scored one of these the other day! About to change the oil and replace the lines and clean it out a bit, do you have a video on servicing these?

Where can i buy the carburettor?

about how much fuel does is use?

Mixture adjustments would be on the needle on the carb slide you can move it up or down a few knotches, that screw in the side is an adjustment for the idal/slide height

良い色だ

Probably the mount break damage was the same thing that bent all the prop blades

Thank you for sharing your experience. You may want to work on your technique. Put yourself in the place of your audience. This could help increase your viewership.

Thanks for the guidance, nog I feel totally comfortable to service my Dt5! Also supercosy with the chicken sound in the background! / Johan

Great review and nice car!

How do you replace the fuel tank

U have to sale

Mine doesnt have tgat scrrw

Asshole....how about doing another video with better sound. I'm def and can't hear a single word but at the end..... that's what I think. Not many videos on these rare stihls 010 av.

People keep saying this is new technology.

I have a 1937 Johnson LT37 and needing the same two items you stated, ... the handle and the spark plug cover. Would you please tell me where you purchased these from? I would be most grateful if you did. Thanks

Elektronika za 7.5 nabavka

brilliant. fewer moving parts

I hope you didn’t charge him extra for that air filter because I watched you squeeze the shit out of that air filter and broke it. I never had an air filter be that hard to come off. This is why I do my mechanic work.

Thought maybe I accidentally clicked ahead in the video. Everything presented was correct but would be better if video showed the actual replacement of the new parts. Tip: After the flanged hex steering bushing was removed, I threaded a length of string trimmer filament up the hole until it cleared the engine bay. Put the new bushing on the line and let it slide down to the hole. A little pinky finagling got it seated properly. My old pinion gear only had wear close to one edge so I was able to flip it over and reuse. Fortunate as the replacement bushing was not bundled with a new pinion gear.

Please where can I get a complete hand control knob for the same engine Can you point me to a place to sell these things?

Thanks, bud!

Does anyone know the correct fuel mixture for these 2 strokes? 1:50 seems to be smoking quite a bit. Should it be 1:100 or 1:50?

Why won't Honda acknowledge this motor exists? All they talk about is the BF5 not THE BADS HP5

But what type of grease? Poly?

makes it sharp

Cripes man trim your house wives fingernails! Looks creepy!

Are these the best engines for small boats ?

Thats the coolest thing ive see all month. This makes me want to get my 12hp viking and 12hp elto on buddy's 16 footer even more. Ha ha

Do you want to get in a Wreck in that. Good Luck.

We just did my sons motor.Without seeing your vid.We got it,but I wish we would have this first!,👍

Short post sucks and long post blows/returns to tank 😊

And...what you think about the conversion of a model year 2004 9.9hp in a 15hp?? The displacement is 255cc... Should be easier...or not?? Ciao dall Italia, and forget my terrible english please...😇