Video

Is it just a normal magnet, and the sites that you have link say they don't have it posted anymore, thanks would be very cool to build

Dear I have problem with SImpleDymo 6.5. SimpleDyno has writen "error reading com" Can anybody help me? I am using WIN 10.

Hello.can u explain the setup for the coil and audio jack.i dont get the signal

Link to the software is not working is there another link Thanks

Hi DamoRC, I hope this message receives you. I'm looking for your original sourcefiles for SD. But the google sites link doesn't work anymore. I'm using simpledyno a lot, but id like to change it from hp to ps and make pin value 5 into dedicated AFR input. I hope you can help me

Hi how are you doing I was looking at your video and I couldn't find the link what the title app I have built me a Dino and I was trying to find out how to put the electronic links and stuff to it if you have any ideas could you share them with me please

Hi I can not find the software at your link below. May you add the new link please ? Thanks. Mario

Very nice , as simple as it gets. Thanks. The link is no longer working . Is there a way to get a copy from you.

Brilliant

is COM communication not supported on win10? i really need help

what a shame that all the information on the forum is lost 😩😩😩😩

Hi! Great work! Pls advise where to get a ardyno pcb or something similar. It seems 2stroke isnt selling them anymore. My email is charles@titan.co.th Thanks a bunch!

please make graphic rpm to 20000 rpm

Love this. Going use this with ardyno shield + arduino to build a dyno for 2 strokes and save me $8000. Thanks a lot sir. I will be most likely be using rpm1, rpm2, temp1. Again thanks.

remove the diaphram from the headphone, it will no longer act as a microphone but the coil will still react to the magnet

i got Ver 6.5...where can i get manual? want to clarify some terms. so stuck up due to that. thanks.

How do you get the program to download to computer the dyno

Thanks a lot it's a good eye opener

Use 18650 battery my shits a beast!

DamoRC1 im not able to download your software. Antivirus is stopping download and removing Trojans afterwards?

You should make a Mac version

Hi ... I'm sorry. I really hope to you to make you have a device like this. Can you make it for rc 1/10.

Used the software and logged 17.2 seconds of data. When we try to look at it on the "Data Analysis" screen, the X graph at the bottom stops at 10 seconds. The graphed lines go past that. How do I set the X to go to more than 10 seconds?

Hi...I want to make it that way. can you help me. where can I get software

Sorry I ment pipe covers

Hi what kind of pie covers did u use n what type of bearings?

this programs a joke and doesn't hardly work

hi, nice work there. could you give the link of software?

Can i get a list of things you used for this. I wasn't able to clearly take note of the things since your voice was vibrating much..also i noticed that there is like a silicon like circle near the axle..what wast that

The graphs and gauges are configurable to whatever range you need. Yes, the software will handle 35K RPM. But if you are thinking of building a flywheel dyno for a nitro engine, you won't be making the flywheel out of plastic and you will probably need to use a one-way bearing so that the flywheel doesn't drive the engine on run down. Look at the X-Dyno setup for more ideas on the hardware required.

In this prototype I used plastic or PVC drain pipe. OD 60 mm, ID 50 mm (or 5mm wall thickness and approx 150mm length. However you should construct your roller to match the vehicle or motor your are going to test. The diameters and mass should give a moment of inertia that is appropriate for your vehicle. The software (new version 6.3 just released) can help you with this.

i`ll try to.

I am not sure I fully understand your question. Can you start a topic on the SimpleDyno forum and post a picture?

what should i do if the graphic just goes straight up?

lol, thats pretty thought full and beast, koo shit bro

@RemoteHelper Can you post this question at the forum. Include pics and information on exactly how you made the coil and which version of the software you are using. I am sure we will get you up and running.

@hothful Almost all of the ones I have seen were built by folks for themselves. Try searching for McPappy brushless dyno, they have just come out with their chassis version. Also check out "Land and Sea" dynos and "DynoMax".

Any one no where I could by one like that

I made my coil, but it is not picking up signals unless I hit the magnet against the nail head. (I;m using a magnetic core). Please help!

@sheilstar12 I posted a tutorial at the forum site for winding your own coil. The smallest coil I have tested is 6 layers of 10 turns, 26 AWG magnet wire. I get a pretty good signal with it.

what coil awg do u hav to use to attach the headphone ?

@KreyNeeUhm Thanks!

Nice work man! Keep it up!

@DamoRC1 Thaank You very much! Ill see how it goes and if anything ill message you with questions! Thanks!

@MrChevyman1996 Have you tried going to the forum site listed in the "more info". There is a lot of helpful information there. Software is simply a matter of checking that your computer is runing the current .NET framework (4) (there is a tool on the website that tells you what version you have=. Then just download the version 5 ZIP file and run. If you are having problems at this stage, just post a question to the forum and I will do the best I can to help you get it working. DamoRC

Can you messege me saying a couple of things needed to this? to actually make it work in your computer? would realli apreciate it man! Thanks!!

@rccarmods It's a 2S3P pack of Li-ion cells 7.4V and about 1500 mAh

what is the output voltage of the battery,that is how many volts

@rccarmods Nope - t is a heavily modifed Radline 1:24, Masters Series

and is that a homemade rc car and how did you made it