Video

Mate this is how a how to video is done. Perfect!

rush 'n attack that carbon!

That alternator still looks brand new and it went out?

How many miles had this car done before you cleaned it?

Thanks dude🤘

Once I saw that that’s a v6 I know why he has taping issues. That’s the valves because that’s a direct injection. Also those motors are piles of junk. Take the intake off and look at the valves you’re gonna cry. Trust me…..

I got quote of $1,400 for replacing power steering rack at dealership. It's rusty and leaking. Is that too high. On my 2010 Subaru Forester

Did u have to get new torque converter or fly wheel because that’s what my mechanic told me I’m going through the same problem I really need ur help I tried dm you

What is the cap you removed from the intake?

How tight should VVT be in? Is there any specific nm that it should be tightened? When i tighten it a little, the magnet is getting stuck. On 1.5rmp, engine sounds like there is not enoguh air for it. Past 2.5rpm it works fine and on idle it runs fine. But on 1.5 rpm, engine shakes and misfires. Misfire sometimes on cylinder 1 sometimes on 3. I got my VVT broken when tried to remove it to replace timing chain. Had to order new VVT from amazon and i think it is low quality. I did timing job pretty good and checked everything multiple times. So how tight should VVT be?

Im finally in permanent limp/2nd gear on my c32, the most common issue seems to be the conductor plate but i have a slight feeling it can be my tcc solenoid bc it was slipping horribly on load before it limped . Does the tcc usually go bad?

Great find. Very clean

Hello. What are the symptoms of a bad oil separator?

YOU JUST SAVED US

You said you would add a link to a tool that removes the oil filter, can’t find the link

Why did you use RTV and not a factory gasket? Also what is the torque specs for the oil drain plug, I had my oil changed at jiffy lube and they tighten it with a impact gun and stripped out the threads on the oil pan. $700 later I’m going to change my own oil from now on.

How do i install mercedes benz software i bought the icarsoft from the link and the 38 pin connector. It says check memory card yours said mercedes immediately

Thank you!!!

Ok, I bought the loop and tested on the amp and the Sirius satellite and it didn’t fix the problem. Does that mean it’s not an issue with either of those?

Think you can use it on Chevy Colorado

Este video funciona para una audi q5 2010 2.0 ?

Thanks for the help brother! 🤘🏼

Sir I have this car and have the same issue with the tranny. Can you list the links for the car plz 🙏🏼 😭

I like the way you explained it very simply, about how do you know, about all that stuff 😂

Surprising that there isn't a wire connector on each fastener

Thank you save me $1400 dollars 😢

I just replaced my turbo... so it was already OUT!!!

Does the cam girdle seal come with the valve cover gaskets?

Best Audi tech on CZcams

Topdon 500 wont work.....for w140

God glees you 🫡

What would happen if you were to not replace the mount ans use that plate on a worn out mount

Can you revive my dream car please

Model number blaater thanks

I had same problem exactly you cannot open the oil pan. There’s a screws behind it so I had to broke the flywheel.😅

I replaced it and every light came on

Сначала прогрева двигун, потом заливают промывка в горячее масло.

Ima do that on my quatro

The video is short, concise and straight to the point. I actually bought this bar but the manual was useless so I had no idea how to use it, especially on where the rubber legs are supposed to sit. Now it makes a whole lotta sense that they seat on the fender. Somehow I thought they sat on the shock towers but some cars have recessed shock towers so that didn't make sense. I'm breaking it out tomorrow since I gotta do a rear main seal job.

Only 12 minutes.

Another job done on my IS 350C thanks to this video. I had to watch it in conjunction with another video to get the full picture. This is perhaps the most annoying repair I've done thanks to those hard to reach nuts and clips. About 5-6 hours total, including time spent having to go shopping for long extention bars. Someone else commented on a left-handed back-reach for that nut in the far back, this tip helped a lot. You gotta take off your gloves and feel it with your fingers. I bought the mirror that he used in the video, thinking it was a stupid purchase, but I ended up using it a lot. Another tip I would give is that when you finally get the new alternator in place after dragging your balls through a mile of broken glass, don't be tempted to screw in all the secondary nuts. I made the mistake of saving the two primary bolts for last (not intentional. I forgot about them until everything else was screwed back in), and thus the Primary-short bolt was crossed, I had to use a long wrench to really screw it in. If i had to do it again, i'd definitely put in the long and short-primary bolts in first, then the last nut in the back, and then all the secondary nuts after.

Yo I'm in Vegas also. My 2017 c43 clunks whenever I left off the gas and I think it might be this. Can you check mine out? Thanks in advance

Nice work man, with all the fun doing that stuff, it’s always interesting doing it 😂

Thanks a lot Cole . I am a retired Motor technician and am used to changing items like this . However the IS 250 is very awkward and your video is excellent, particularly explaining where the hidden rear braxket is. Thanks very much . James Perriam Exeter U K

Great video, I am attempting to do mine today

God damn. I hope this works for a 2003 outback vdc

Is there a way to reset the inspection light on a 2022 Q5 PHEV?

I owned a b5 a4 AEB qnd did coilcovers, the nightmare of my life🤣 pinch bolt sheered and broke in the knuckle and i had to drill it out, blowing so much money on cobalt and titianiam bits to trill it out

My vw golf 7 gti in the cold start I feel some tremors and hiccups then in progress all normal but if I put it in D or N stopped I feel again will it be from the magnet covers or the valve?

Do I need to change de spark plugs when I replace the ignition coil ?