Video

I have the Alpine x001 every few months it will not power down doors shut. Only other way was to power down manually. I just tried your technique pulling amp fuse and it powered down I wonder what’s causing this issue

Yes I'm necrocommenting on an 8 year old video because it's still relevant and thanks for making it! WD-40 is awesome. I started using it instead of armorial on molding rubber and plastic as an experiment and got on the CZcams to see if anyone else did it and I found you. I think it looks better than armorall. Less glossy, more classy. I was using WD40 to polish chrome after using degreaser to get some rust-run off and tried it on the plastic and it worked like a champ there as well.

how bout awd cherokee? same?

Can't we do this without a remote, just using the motor? Do you have to be outside the garage to do it? Can't you do it inside the garage? What a stupid system.

My jeep doesn't crank or starts 2005 jeep wrangler 4.0 am trying to figure problems

Wow thanks so Much; Easy Peasy AWESOME 😎

Hey, might be a silly question but the 5v on pin 17. Is that key on or off or both?

Hi bro So, so far so good 6 years after this video? Thanks 😎👍🏼

What?? Face your camera towards it??? How does that align anything?? You didn't move the sensors and they werent out of alignment in the first place!!

Awesome video!!! But us ladies are pretty capable too! 😊

Great job on the install. How has this radio held up since it has been 4 years. Thanks again for the video.

The gasket is in wrong position that is the engine side of carb you figured it out 😊,

I need that on my 2017 jetta

So you're saying that the struggle was real Jerry??😁😁

Question… My rear differential seems to be leaking a little on one side from where the axle goes into it. It’s a brand new axle. Could it be a worn out or busted at the rear differential? Any pointers on how to fix that leak?

Can you anti seize the ball joints?

Oioi Jerry hope your well buddy

Very helpful thank you, I picked up one off marketplace late Fall and just hauled it out now to use.

When checking the atator for ohms. Where were the leads placed? Are there specific leads you're going for ? Like there are one horizontal lead and 2 vertical ones

Thank you too much master

Song name ? 1:40

So I just remove the existing standard spotlight and hook up the LED into the same circuit which I'd put in to run that? Its all in place ready to go but I'm not really all that familiar with LEDS. Just that I'd heard there was a difference in voltage required or there could be differences in voltages? What's that about? I had the same KC as you have for many years before it finally burned out and now just a 100W which is pathetic by comparison so thinking LED would be next choice.

Great video..As for the product I guess I don't get the value of The Eliminator when a crush sleeve is only 10 bucks and just torque it and go and yeah you may have to spend 10 bucks again if you go back in but how many times you going back... Just seems like more hassle than Reward

I have a trans coole twice that size on my 14 tacoma...it cools about 20 degrees here in az hear ....i wont believe that little cooler will drop temps 60 degrees....lets go brandon🤡🤡🤡

3.8 much easier to work on, heaps of space, real simple and a reliable motor, good vid

This would be great for a gym managing lots of basketballs and volleyballs, etc, where portability is most convenient. Maybe for that 1 emergency car tire inflation. But ill keep my cigarette lighter-powered inflator for now. Just need to remember to keep the car running during inflation or it could burn up my alternator later!

If i have 4 sedan tires that are 10 psi below normal, can airmoto do all 4 on a single charge?

nice video brotha it was straight to the pont

Ad to this you have to have the spacing between the coil and magneto, on the flywheel in proper spec. About 10 Thousands. Business card works .

Your awesome bro!💯 thank you!

Can you leave the vct solenoids plugged in after disabling in the tune or do they have to be unplugged

Quick & Easy 🍻 MOFO Beer Time

Wouldn’t it be a good idea to change the top gasket when you happen to have it accessible? And could there be other reasons to excessive oil consumption?

Can anyone please tell me which of the 4 sensors are heated? 07 JKUR. Please. 🙏

Mannnn I’ve been longing to do this! No salvageable hitches near me sadly

I always like your no nonsense approach to working on and fixing stuff.

its so much more fun when done on the machine!

Had the hardest time getting 17mm on the front diff. Try again tmrw, good video. Looks the same as my 2014 550

Great tip Jerry.That is how I normally do it too..

I have a Chinese engine with no small triangle under the recoil starter. How can i adjust its valves correctly?

Great video

So where would I look to chase terminal 30 which is to the constant power feed? I have none on my 97 tj. Where is it fed from?

You don't need to take that plate off that holds the the spring and arm, the bolt to the left is on the carburetor is all you have to take off

Missed the part where the airbox gets removed. Dog shit vid.

Bought mine today exactly the same but in South Africa under the name MacAfrica exactly the same very nice machine good quality love it.

Thank u!

What size do you tap the main shaft with? 3/8 Fine or 3/8 Coarse?

Lesson #1, never use power tools to remove pulleys. It's easier but you can easily damage the pump in doing that.

worked!

So badass 😂love it