Video

Hi Ingus, I have been following your CZcams for quite a long time now. I have a challenge recently on Yaskawa v1000 vfd. It was initially on source mode and was later changed to Modbus when the machine electronic board got burnt. The owner of the washer(Atoll 350) sent the vfd to Germany for reprogram to a new upgraded electronic board. Now, the upgraded board and the vfd came and it was installed but it is not working as it should, the motor rotate very sluggishly and pausating as if there is serious friction but when rotated by hand it's very free. I tried to gain access to the inverter all to no avail, only A1-01 and A1-04 could be accessed. What can I do and what parameters will I adjust as there is no handy manual. Thanks.

can you explain the power wiring as well. I am bit confuse as my powerflex has single phase input and three phase out but I don't have the three phase load to test. How I can test with single phase load????

Thank you for your clear explanation...

Это лучший ПЛК в классе микросистем

Hi Which parameter is it to enable the TA-TC normally open relay function so I can power a contactor for a holding brake? Thanks in advance.

Thank you for the video. I’m completely new to VFDs, and I got one of these second hand. The instructions are good, but going back and forth is sometimes confusing. This is a great how to set up guide, wish I’d googled earlier!

I HAVE a question about the choosen telegram 3 . as i read from siemens help the telegram 3 doesnt support the IRT it only support RT but why you choose the isonchrounous mode in the paramaeters ? i think you should select telegram 5 or 105

Hello, can you provide me a link for E-Designer V6

I have the error OI AC could you plz for this

Thanks sir

Sir for simatic manager how to do the incremental encoder homing program And how to reset the encoder value please help me

Parameter not set with error

Parameter not set with error

Parameter not set with error

If I stop the drive the fan will still on

Thank you Sir...

When I followed all this. The motor won't start it just comes up F0001. Any idea what's wrong

Hello, I would like your help, I need to do a project. The PLC, an FX3U, will send the MR JE C servo to rotate to one side a certain amount of pulses entered into a register on the Sankoom HMI, when it reaches the count, the servo returns to the value of 0. Could you help me with the pins of the CN3 connector and the configuration parameters in mr2?

What solution of spi test ok on ?

When I upload to the device it is encoded with cl what is the problem

When I upload to the device, it is symbolized by a letter CL

Thank you for video,i i have V1000 connected to the fan touch panel controler,but when i am trying to run the fan from the control panel it is not working even i can see/change controls on the touch screen and on v1000 drive i can see that freequecy is matching the input on the touch panel/controller...but fan is not working...the only possibility is to run the fan by pressing/changing V1000 the local and then change frequency....is there any video that may help me please?Thank you!

What meaning spi test ok??

Really interesante

The estop set up you have shown is not appropriate .Power supply This typical installation using CFW500 with Safety Functions fulfils requirements for safety performance SIL 3/ PLe and Cat. 4, according to EN ISO 13849-1 and IEC 61508, Stop Cat. 1, according to IEC 60204-1. CH1| CH2 6001 PBWTY + BESG (self-monitored emergency push-button) CSW-CK2F45-WH 國08 CFW500 with CFW500-SFY2 plug-in module

What what?

Hi good vid thanks .. how dou you set to rdy from inh as I'm unable to do this.. I tried p5 on pad to run manual indicator light on bottom right but unable to run? Cheers

I need help bypassing a Schneider 3 phase Vfd. It’s on a new unit under warranty and Vfd is bad. I need to jump out the L1 L2 L3 to the T1 T2 T3- any help?

Am falling to program this type of to work on R/F, please hey me on how to program this

Good day, Sir. Thank you for the informative video. I just wanted to ask about an issue I'm having with a .FX file. My GX Developer can't open it. I hope you can help me with how to open it.

Hi mate, I was just watching your video on the Mitsubishi PLC from 3 year ago, is it common for them to completely stop working on 1 output, it just will not produce 110v when pressed

If you want to display Commanded Freq select b002. Default b001 displays Output Freq.

Can we able configuration digital input to fault reset with drive relay? Is it possible? When fault accoured does configuration do reset automatically?

Thank you for this video and for sharing your knowledge and experience. I'm just trying to understand whether or not this will work for my project. I need 4 inputs and 4 timed outputs which will operate separately and one at a time. seems simple enough.....thanks

Hi what kind of potentiometer did you use ? Is it 1kOhms or 10kOhms ?

Great video, what about if the PLC has a red led turned on in SF and there is no card on the slot, do you think could be possible to get a backup from the plc under the conditions described above? , sorry for the akward question but I am new with Siemens PLCs, thanks for your support

I'm using a CB 1241 - 6ES7241-1CH30-1XB0 (Rs485 module) which firmware version is 1.0. I cannot find an update firmware for this does this mean I need to buy another rs485 module to get this to work?

I enjoy the information, thank you for the swift way you're doing it... I have a question about password usage... Or how to get around it... Waiting for the machine getting to my workshop and I was told that the plc is "stuck' (???) and the "guy" that did first diagnosis said it's password protected... (???)

Is the program for a real machine and what is the name of the machine?

The transfer mode not working if use to the same but a new PLC, keep blinking (TIA Portal V18) with password and Know-how Protection, any suggestions to solve that matter?

Very clear tutorial, many thanks.

can this drive be run on 0 - 3.3v? Eg. putting it in 0-5v mode using Al1 and com and somehow making the drive run at 100% when it reaches 3.3 and hold all the way to 5v?

COOL. Im thinking of buying a second hand 0BA5 off eBay but Chat GTP tells me it wont work with version 8 software. Apparently i need to V6 or lower.

What is "positioning axis1"? Where does it come from?

Hello, I have beijer E200 version 6.04 with boot 4.13 Does anyone know E designer that supports that version? Thanks in advance

BICO PLZ Sr

🎉🎉🎉 Great my Lord

where is the download link ?

Awesome DVF🎉

Thanks very much, great tutorial. Your video is much easier than reading the manual.