Video

You are extremely detailed and very insightful, truly a great help even now!

Sir! You just flagged me with your disassembled bolt! Sincerely, Safety Sally.

Great job

FN FAL. It's far less finicky about ammo, and doesn't ruin your brass (unlike fluted chamber G3)

Jus use ur thumb instead of screw driver much easier

That Toth tool with the squeezer is the best method in my opinion. I’ve used rivet jigs and pneumatic squeezers but I always go back to the Toth tool squeezer. It gives me more control. And as you have shown, it’s quite easy to correct a lopsided rivet head.

Excellent

I served the Mexican army and used the fal 7.62 mm good riffle and very reliable..

30-06 would be 7.62x63 I have a 1952 Springfield M1 Tanker.

It totally different with Brandon Herrera's version which using Tokarev ammo and still using AK chassis

Beautiful work! Thanks for sharing

And I’m amazed at how beautiful the rifle is, I myself served in the Soviet Army with an SKS carbine.

Word of advice when doing your through rivets and forming the tail, try and avoid hitting the center and try and form a dome shape with no flat to the face. The more you form a flat face the thinner the edges will get, may make a pretty rivet but it will form a dome shell because the rivet wont swell properly leading to a weak rivet job

Are you supposed to countersink the receiver into the rivet holes before putting the rivets in? Or does installing the rivets sink the receiver into the dimpled trunnion holes?

Nice 👍 rifle

I used a 1" steel round bar ground flat and to fit, then pressed it with a 20 ton press. But the trigger guard rivets I could not do, so used small bolts and nylock nuts.

This is an excellent video. Not just for its content but for the way it was presented. Absolutely superb. Too often people are so busy just talking they put you off. This was a refreshing video to watch. Thank you!

In a combat rifle it isn't a sniping weapon, however the HK is remarkably accurate. Mine has the polygonal barrel. I have never seen it get dirty. I like the mushy trigger. On rapid movement, I don't want a light trigger. However I like it to break cleanly when it gets done traveling around ! That is easy to modify by anyone at home. The FN Gas operating is fine and tunable, but has a lot more parts to clean. The HK has only 2 main operating parts. They either work or they don't. Replacing the bolt and any part in the action takes a few seconds. And parts are inexpensive and easy to get. They made MILLIONS of HK's. The HK is also easier and faster to strip clear down to all moving parts to replace, fix or modify and has many more spare parts that are cheap and easy to buy. The entire trigger group is interchangeable with several of the full auto, and semi auto guns, and is simply made out of stamped steel. Easier for home repairs, very easy to do your own trigger job. Almost any of the similar models to the 91 can interchange parts. It does have a bit more recoil. I can't tell the difference in a fire fight! It also has much better iron site with the rotating rear drum sight. The HK does throw brass!! No one is going to flank you on the right side ;-) That brass can go 15 feet. It won't pile up in your fox hole. We simply extend the ejection port and glue in a small rubber bumper. It won't dent brass that way and with your dremel tool you can modify it to toss brass from 1 foot away to 20 feet away anywhere from the 2 oclock position to the 5 oclock position. I have reloaded dented brass several times in a row, with no safety or reliability issues. I don't recommend it, but have done it thousands of times during the 10,000 rounds I have put through the model 91's. You can easily put in the machine gun model recoil buffer and significantly reduce felt recoil. You can put on larger hand guards and larger bolt latches and a better magazine release on the side button. And we put a tab in our magazines to hold the bolt open on the last round. You can insert a magazine in the HK with the bolt open or closed, or even with a round in the barrel, it doesn't care. The flash hider on the original is fine but all the other brands needs to be replaced. The FN is a fine rifle. Easy to carry. The HK is simply a much tougher gun and can work in dirt and freezing mud that would stop the FN even with it's tunable gas ports. The HK will probably last forever, or longer if you remember to clean it, or even if you don't. And it makes a decent boat paddle.

Very good

Always make sure of your target .

I had the opportunity to use both rifles during my duty in army. The G3 is a toy, easy to loose the target - specially for inexperienced shooters and gets VERY hot VERY fast. The FN FAL is simple a COMBAT rifle.....the only minus is the long (very long) barrel....

Wow what an awfully misleading title

1. A place for the 308 2. A more reliable platform than an AR10. 3. Still accurate and ergonomic for CQB. 4. Parts availability for maintenance and repair. 5. Better at Armour defeating at close to midrange.

I like FAN❤

You are a god. Thank you so mich

Are you still make video

Foi a minha arma no exercito, G3, tinhamos que desarma-la e voltar a armar com os olhos vendados em menos de dois minutos, e para desrmar o grupo do pin de disparo usavamos a bandoleira, muito mais rapido e muito mais facil.

How about, "Owner Assembled"?! I think the point is you can build/assemble your own rifle from a kit/parts with minimal tools, which is really a wonderful concept.

I have run both extensively. The FAL is a fine piece of ordinance as is the 91 - G3. The roller delay actions require more on the tuning and, as any roller delay system, if you reload - you can forget it on these. Roller delay actions destroy the brass. The recoil impulse is much more violent whether it is felt or not.

I set the assembly up in a vise loosely and used a air hammer that had been cut flat and a dimple made in the end It didn't take anytime really to do it, and came out great. I built two that way.

Minta saj ama pemerintah jika terj perang ribet

I have the same gun with a 36 inch barrel in mod

That looks like it took a round. They aren’t matching? Maybe the original is blown apart. Looks very nice.

Thanks man

Hk

Which is better? Both

Can it also have a wooden foregrip?

Remington?

Talks about safety sally but lives in California. 🤦‍♂️🤦‍♂️🤦‍♂️

I had to replace my Trigger in my HK91 now it's a 3lb clean break trigger, it has a Paddle Release so that's helpful. I honestly love mine. Never owned a FAL so maybe biased lol

I think the SKS is perfect for SHTF, no mags to carry or damage and if you have no clips you can still load it, they have a cleaning kit in the stock and a bayonet

Any idea how to replace the recoil spring on a retractable rod? Its what the pdw comes with.

CETME C3

S&W quality was much better back then.

I have to say, I’ve never seen a better advertisement for grease in my life. LOL

What’s the hk 91 handguard metal hook used for?.

I have an old Mossberg 151K 22 LR I will rebuild from break by a tractor "stepping up" on it. It needs full reblueing, however, i duda note find the SN engraved on it's action. Do You know where it should be?

I have one just like that 31-1 my bottom on handle atarts with ABM what does that mean mine is the same blue how much are they going for I've been Interested in maybe selling mine .

I mean people can do hard drugs and shit on public sidewalks and rob Walgreens but they want to limit your ability to defend yourselves??? I just don’t understand it.

I get trying to be compliant with the law but you guys in California have to do a better job on constitutional rights.