Video

Hi don't know if your checking messages on here still but I'm just a Mom with a Dacor Oven that has not worked for 8 months. With holidays approaching I really need to figure this out. A repair guy came a long time ago and quoted me $2600 for new relay board and something else. I about fainted. The oven stopped working when I had guests over with the broil unit on and forgot about it. Think the oven got too hot. What does work is the behind the back 'wall' and so the oven can get to about 260-270 degrees but top and bottom element do not work. Anyway, I tried to reset that red button but dang its in a hard place to reach....do i keep pressing hard on it? I cannot pay the money for the repair so i have to figure this out 😞 Thnak you....Jana

I Had to take off the front cover.. the rear spring is difficult just taking off , can you imagine replacing it.

Hi Todd, Great video!! I have a Dacor MORD230 Double Wall Oven, and recently the lower oven started overheating. Seems like when it reaches the set temperature, it does not stop heating. I can hear a relay click, the element turns off, but then turns right back on again. Any thoughts as to what this could be? The upper oven works just fine. Thanks for your feedback.

How much was the board and where would you get them

Thank you for posting this. I was ready to throw out my oven but you saved me. Thank you so much!!!!!

Do you have any info on replacing the door hinges?

$300+ LOL

Thank you for making the time to do this video. I’ve watched 10 this morning and this is one of the best and most helpful/informative.

Would love to see a video of repairing the door piston/hinge as ours is doing the same thing (now very heavy)

Thanks for this great video! It was exactly the same problem on my DF366 with oven not working. Was one of the soldered connections for the DLB (DBL) breaker/contactor on relay board. Took a couple minutes to re-solder and back up and running. Also had a very dim display and after removing and reconnecting the cable it is bright again!

I have the same combo but it has a different agitator

Why dont you show how to use that tool. Im am lost i cant put the spring back on. I have that tool. But cant do it😮

hola soy de venezuela mi lavadora esta presentando esta falla, se le ha cambiado el acople, pero lo parte, ya se le han cambiado 5, pero vi en el video que también cambiaron el aspa, sera por eso que se parte el acople entonces, claro esta vez tengo que cambiar el aspa porque tambien se partio

Hello! Where can I order this whole set! My washer is having the same problem.

I’m having a very difficult time getting the big nut off of the shaft of the motor.To confirm it is supposed to come off so as to facilitate putting on the new blower wheel?? Any help is appreciated Thank you in advance

I appreciate you posting this because it helped me out! I also had a cracked wheel and had to bust it out to remove. Got the new blower in now. Thanks!

well done, thank you! Just lost my display last night. It died all on it's own. no self-cleaning involved.

Thanks for the video

Todd, awesome videos (part 1 & 2). Thank you! I might venture into fixing ours now, but where are you located? I’d rather have you do it! 😅

How do i get the plastic teeth to line up sounds awful

Hi Todd, mine was moving but the water Keep filling and never get to the wash cycle. It only do drain and but not wash.

What is the part number

Hi Todd, I’m pretty sure I’m having the same issue as there is a loud rattling coming from the top/back of the oven when it gets warm. It’s definitely not the convection fan at the back as that works fine and this noise happens not on convection mode. I have an RSE30B Dacor, do you know the part number I would need? If not I will have to take it apart and look. Thanks!

I have the exact same oven and it went dead after self cleaning. Where can I find the model number, I can't open the door?

I took the agitator out just to clean it and was in shock how dirty it was at the bottom of the washer 😱😱😱, there was so much dirt, how can I clean it? 🙏🏼 any advice?

Great video! I have a 15 year old Wolf Range model #DF364G that the oven stopped working and I went down the line and tested everything before I dove into pulling the board. I was having a hard time finding a board so I decided to take it out and see what the deal was with it and it was a cold soldier joint. I tested the relay and everything checked out. So I dove into it and cleaned it up and resoldiered it to the board and put everything together and it worked perfectly! Thank you!

Hi, Todd. Thanks for video. Can you give your phone ? I have questions about Dacor ( we have error codes U70 comm error and door engaged)

Im having the same problem after running a self cleaning cycle. My problem is the door is on the locked position with no power. How do I remove the oven without having access to the screws that attach the oven to the trim panel?

I got new inverter. Still didn't work. Took it apart again and found one of the wires in the connector was slipping out and wasn't clipped onto the motor. Worked fine after making sure it clipped on correctly.

Bless you! New oven thermal fuse fixed it and saved me hundreds!

Looks like a two stage valve low simmer ring not igniting Need to clean the small pin hole port by stiki g a long pin down the simmer feed chamber

I have the same Dual Fuel Range and my ovens get hot but I have to set them to 400F if I want it to heat to 375F. I wonder if I need a new thermostat?? Any idea?

Why not get someone else to hold the camera?

Thanks

Thanks for this video! I have this oven and problem. Good to know what the problem likely is.

In case you are in NJ, let me know I need similar help. Thanks

hello Todd i hope you can help me here I have a bosch b36cl80sns/07 fridge and my fridge is dead. i have 110 power in and going to the ice maker but nothing else. can you tell me the voltage that is supposed to come out of the power module to the main board. Bosch cannot or does not want to help.the fridge is only 14 months old.any help would be appreciated thanks

Thank you for these great videos. My Wolf DF304 oven stopped working and after walking through all your instructions I was able to confirm that it needed a new relay board. I was able to find an oem board on eBay for less than half what Wolf charges and everything works again.

Hi Todd, I have a dacor double wall oven like you are servicing. For some reason my clock button does not work to allow me to set the clock. I have seen some posts indicating I may need to replace a board. I’m curious your thoughts? Also wondering if it would be the upper board or lower board? Or if there is something else that I may need to replace?

is it normal jennair single upper fan be on when starting unit? Should kick on after oven heats up

Yep. Paper clip did the trick.

Not sure if you kown but your videos are set to made for kids...that limits your reach and also comments. People can't comment on those videos

Good stuff buddy!

At the bottom and inside of the agitator, there is a small circular piece. Mine came off. Can it be put back with the agitator? If so, which side is facing which direction? Thank you.

Would this be the same process for a single Dacor oven? Model ECS130, looks very similar to the one you are working on.

Handling a damaged Wolf cooktop gas valve is serious business. Your video tutorial ensuring both safety and functionality. And remember, we've got all the authentic Wolf replacement parts to back you up.

Thank you ! Restored the fridge to life!

Thank you

I have the same washer/dryer combo I recently replaced the spin bearing (3204405). When I first ran the machine there was a slight squeal. Now after 5 uses the new bearing is squealing annoyingly after 5mins on spin (doesn't do it straight away). I'm wondering if I damaged the new bearing getting the tub down the shaft. What do you think?