The Infernal Craftsman
The Infernal Craftsman
  • 66
  • 185 473
Bauer one year update. Would I buy it again?
Just an update on the tool since no one does long term updates on new tools.
Link to my Amazon wishlist if you want to support the project.
www.amazon.com/hz/wishlist/ls/3U6AS7Z2KAY9G?ref_=wl_share
zhlédnutí: 551

Video

Things didn't go well in the shop today..
zhlédnutí 1,7KPřed 3 měsíci
That didn't go according to plan. Started off as a decklid prep video and a bauer SCT new brush video. Ended in anger and destruction. Link to my Amazon wishlist if you want to support the project. www.amazon.com/hz/wishlist/ls/3U6AS7Z2KAY9G?ref_=wl_share
Interior painting the 66 mustang. Two tone color
zhlédnutí 351Před 4 měsíci
My preferred paint supplier www.clarkswholesalepaints.com Link to my Amazon wishlist if you want to support the project. www.amazon.com/hz/wishlist/ls/3U6AS7Z2KAY9G?ref_=wl_share
Making the 8.8 rear one piece again
zhlédnutí 208Před 5 měsíci
Welding the 8.8 back together and lots of info. Link to my Amazon wishlist if you want to support the project. www.amazon.com/hz/wishlist/ls/3U6AS7Z2KAY9G?ref_=wl_share
Cutting an 8.8 axle with the cheapest bandsaw on Amazon
zhlédnutí 329Před 7 měsíci
Using a Silvel bandsaw to cut down a ford 8.8 axle. Link to my Amazon wishlist if you want to support the project. www.amazon.com/hz/wishlist/ls/3U6AS7Z2KAY9G?ref_=wl_share
8.8 narrowing for a Mustang
zhlédnutí 409Před 7 měsíci
Part 1 of narrowing an explorer 8.8 to go into a 66 Mustang. Link to my Amazon wishlist if you want to support the project. www.amazon.com/hz/wishlist/ls/3U6AS7Z2KAY9G?ref_=wl_share
Back in the shop. 8.8 rear axle, electric power steering and delay wipers in the works.
zhlédnutí 329Před 9 měsíci
Lots of projects in the works. Electric power steering, 8.8 rear axle delay wipers etc. Link to my Amazon wishlist if you want to support the project. www.amazon.com/hz/wishlist/ls/3U6AS7Z2KAY9G?ref_=wl_share
Cheap easy DIY body cart for a Mustang
zhlédnutí 1,3KPřed rokem
Super simple body cart for Mustangs and similar Fords and other cars. The Mustang is finally off the rotisserie... Link to my Amazon wishlist if you want to support the project. www.amazon.com/hz/wishlist/ls/3U6AS7Z2KAY9G?ref_=wl_share
Custom Coat bedliner undercoating on the 66 Mustang
zhlédnutí 753Před rokem
Black bedliner as undercoating on the Mustang. Custom coat 4 quart kit. Barrys application of tinted bedliner on a bronco czcams.com/video/gLVdEmM-mC8/video.html Link to my Amazon wishlist if you want to support the project. www.amazon.com/hz/wishlist/ls/3U6AS7Z2KAY9G?ref_=wl_share
Welding the last pieces on the car and talk of coming off the rotisserie.
zhlédnutí 423Před rokem
Welding the last two pieces I know of that I have forgotten then just put off. Next up is bedliner on the bottom of the car before it comes off the rotisserie and onto a shop made body cart for 2K primer. Link to my Amazon wishlist if you want to support the project. www.amazon.com/hz/wishlist/ls/3U6AS7Z2KAY9G?ref_=wl_share
No weld camber plates for 65-66 Mustang
zhlédnutí 1,4KPřed rokem
I didn't want to buy camber plates but I did want the extra adjustability if I need it. So I made my own. These would also be an option for other Fords like Falcons that use a similar system. Link to my Amazon wishlist if you want to support the project. www.amazon.com/hz/wishlist/ls/3U6AS7Z2KAY9G?ref_=wl_share
My method for filling leaded joints on quarter panels
zhlédnutí 1,2KPřed rokem
My method for replacing lead with filler products. May not be the best but it's how I do it. Link to my Amazon wishlist if you want to support the project. www.amazon.com/hz/wishlist/ls/3U6AS7Z2KAY9G?ref_=wl_share
My take on basic seam sealer
zhlédnutí 1,9KPřed rokem
Simple single part seam sealers that the home shop guys will be using and comfortable with. Two parts are great but pricey and IMO overkill for many classics that will never see rain and see very little sun. Link to my Amazon wishlist if you want to support the project. www.amazon.com/hz/wishlist/ls/3U6AS7Z2KAY9G?ref_=wl_share
CPP Mini subframe and Viking coil overs install part 2
zhlédnutí 5KPřed rokem
CPP mini subframe kit install and rambling about odd old suspension designs... www.classicperform.com Link to my Amazon wishlist if you want to support the project. www.amazon.com/hz/wishlist/ls/3U6AS7Z2KAY9G?ref_=wl_share
CPP Subframe install in 66 Mustang
zhlédnutí 4,4KPřed rokem
Subframe install didn't go a planned. But is being taken care of. An overview to my Rotisserie build. czcams.com/video/vOG8DZCgjzs/video.html Link to my Amazon wishlist if you want to support the project. www.amazon.com/hz/wishlist/ls/3U6AS7Z2KAY9G?ref_=wl_share
CPP Front suspension Mini subframe kit for 66 mustang overview
zhlédnutí 6KPřed rokem
CPP Front suspension Mini subframe kit for 66 mustang overview
Back to work on the Mustang (finally cooled off)
zhlédnutí 501Před rokem
Back to work on the Mustang (finally cooled off)
Update on the 66 Mustang project
zhlédnutí 434Před 2 lety
Update on the 66 Mustang project
4 methods for media blasting at home
zhlédnutí 762Před 2 lety
4 methods for media blasting at home
Finally paint on the belly of the 66 Mustang
zhlédnutí 1,2KPřed 2 lety
Finally paint on the belly of the 66 Mustang
66 Mustang prime day an intro to epoxy primer.
zhlédnutí 1,7KPřed 2 lety
66 Mustang prime day an intro to epoxy primer.
Basic paint stripping tools for prepping for paint.
zhlédnutí 1,2KPřed 2 lety
Basic paint stripping tools for prepping for paint.
Media blasting and Putting the Bauer SCT to work on the mustang.
zhlédnutí 1,2KPřed 2 lety
Media blasting and Putting the Bauer SCT to work on the mustang.
Harbor Freight Bauer SCT review
zhlédnutí 16KPřed 2 lety
Harbor Freight Bauer SCT review
66 Mustang Torque box braces
zhlédnutí 2KPřed 2 lety
66 Mustang Torque box braces
Wiper motor bolt locations in a 65-66 mustang
zhlédnutí 5KPřed 2 lety
Wiper motor bolt locations in a 65-66 mustang
Shop built Rotisserie for the Mustang overview
zhlédnutí 1,8KPřed 2 lety
Shop built Rotisserie for the Mustang overview
Cheap Mustang rotisserie leg build part 3
zhlédnutí 777Před 2 lety
Cheap Mustang rotisserie leg build part 3
Cheap Mustang Rotisserie 2 C/G balancer build
zhlédnutí 1,1KPřed 2 lety
Cheap Mustang Rotisserie 2 C/G balancer build
New shop air hose reel from Walmart of all places
zhlédnutí 4,9KPřed 2 lety
New shop air hose reel from Walmart of all places

Komentáře

  • @stevepope5484
    @stevepope5484 Před 2 dny

    Looks good though

  • @stevepope5484
    @stevepope5484 Před 2 dny

    Deadner? Its metal snd and it isnt complete. Dont hit on your fender. The other sounds like 1/2 of bondo.

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 2 dny

      Yup sound deadener makes for a far quieter car. And easy to put in while the quarter is off. Nearly impossible later. The factory used a spray on material similar to 3m shutz

  • @stevepope5484
    @stevepope5484 Před 2 dny

    I'm thinking I'll patch my inner fenders too. I bought new outer. Innerspring ain't great either?

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 10 hodinami

      The rear wheel houses are really hot or miss on fitment. The dynacorn ones tend to fit well. But the cheap ones out there seem like they are using the old 1980s stampings and don't fit much anything.

    • @stevepope5484
      @stevepope5484 Před 7 hodinami

      Thanks. I'd allmost screw this stuff together for the next sucker/guy. Same them the extra work to get apart. My rockers are barley there on the end. Oh well. The inner wells when they arrive//guess I allready said/probably a waste of money /but the inch or 2 or 3 where it's welded to the flat trunk thing/ then ea.end. My friends think I'm an idiot for fooling with this junk. Probably .Ha!

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 6 hodinami

      @@stevepope5484 You will get there. Spend the time to replace the stuff deeper in. Sometimes you can repair it with new steel but if you don't you will know what's hiding in there and it will come back to haunt you. But do it right and you will be happy with the end result and sleep well at night knowing nothing is hiding in there

    • @stevepope5484
      @stevepope5484 Před 5 hodinami

      Thanks again!

  • @stevepope5484
    @stevepope5484 Před 2 dny

    I made a ruff cut with my sawzaw

  • @benharper1682
    @benharper1682 Před 8 dny

    great job. How much would you charge me to build me one lol

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 2 dny

      I wouldn't build it for anyone else just due to liability reasons. It's fit for my purpose but may not be for someone else.

  • @gc1979o
    @gc1979o Před 12 dny

    How do you find what the new output rate is dont you need to know the new efficiency or how do you estimate it ? Thanks

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 10 hodinami

      I would estimate you would loose around 2500 watts when running off propane and a little more off of natural gas. But just a guess going by other brands that have numbers on it. That said I don't know if the numbers anyone lists for output on any fuel can be trusted. Kind of like air output of air compressors. Who knows ...

  • @RotarySMP
    @RotarySMP Před 15 dny

    It has been really nice here in Naxos again. They are doing some serious work with barges and big crane in the harbour after that collapse you talked about. The sun beds have increased dramatically in price (€25-40 a set now), but the restaurant prices have not changed much. We do our daily walk from Prokopios to the bottom and of Placa beach. 11km round trip. Then I did a 90 minute swim in crawl out to the northern tip of Prokopios bay in the afternoon. If I did this much exercise at home I would be in much better shape.

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 15 dny

      Awesome. If I come up with anything to give you I'll drop it off with my friend over at Xenia hotel close to where waffle House used to be. We havent bought our plane tickets but are getting close. Late September. Holding off cause one of our cats has had some issues and want to make sure he is ok. We never did the sun beds we usually get an ATV and check out the villages etc. I want to stay in mountsaona or somewhere else this time. My friend lives on the north end of the island 300 meters from the water and may stay up there instead. No plans till we get plane and ferry tickets. Prices are much lower this year.

    • @RotarySMP
      @RotarySMP Před 15 dny

      @@theinfernalcraftsman We are real beach bums. We always stay in Prokopios. We have been here about 10-12 times in 22 years, but only ever rented a car once, for one day, and drove up the north , then north to south down the middle of the island and back up the coast to Prokopios. We do tend to take the bus to Chora one time each visit. We did that a couple of days ago :)

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 15 dny

      @RotarySMP There is a cool corundum mine in Koronos that is wide open. Just walk in. I'll see if I can find an email for you and send pics . Lots of cool places to go on the island.

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 15 dny

      @@RotarySMP Couldn't find an email for you. Send me one on my channel name and I'll send you a link with the pics of the places around the island we go to. The hike up to Zeuses cave is a tough hike for us old folks. The first time we walked from the bus stop in town down the wrong road then up to the caves. I can't make that hike anymore.

    • @RotarySMP
      @RotarySMP Před 15 dny

      @@theinfernalcraftsman Where the hell have YT hidden our email addresses? they used to be on the channel "about" page, but that is gone, then there was a "business inquiry" button, and that is gone.

  • @stevepope5484
    @stevepope5484 Před 28 dny

    Who does the axels?

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 22 dny

      Ford. You just use 2 short axles from the explorer. This rear was bought primarily for the 3.42 gears and the short axle.

    • @stevepope5484
      @stevepope5484 Před 22 dny

      Wow! Thanks!

  • @stevepope5484
    @stevepope5484 Před 28 dny

    That piece of foam and the staples is correct! Just like mine.

  • @stevepope5484
    @stevepope5484 Před 29 dny

    Squeegy

  • @dm7097
    @dm7097 Před měsícem

    I am at the end stages of my project ‘66 coupe, and I believe the wipers were the only item not removed from the car! lol I believe that I did replace the shaft gaskets, but that doesn’t require the whole apparatus to be removed.

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 22 dny

      Awesome. They are often not removed. There are two different gaskets for them. A leather one and a rubber type one they used. It's a question of which do you trust more to not leak. I'm Ok with either style.

    • @dm7097
      @dm7097 Před 22 dny

      @@theinfernalcraftsman I honestly don’t remember which ones I used. I would tend to believe I would have went with the rubber ones, but not sure.

  • @cjhoyt9876
    @cjhoyt9876 Před měsícem

    Nicely done Rick, were did you come up with the numbers to set the height to? I used the BCI floor joists with 2x6 and the Ford datum sheet to set the height to

    • @theinfernalcraftsman
      @theinfernalcraftsman Před měsícem

      Made them up out of thin air. All just a guess on what I thought would work. Now I wish it was a little higher for working underneath but then would be too high to work on the top .

  • @shawncoffin1153
    @shawncoffin1153 Před 2 měsíci

    Best video I’ve seen for a Mustang quarter and keeping the entire seam. Awesome job!

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 2 měsíci

      Thanks. Sadly I didn't start filming until later in the project. I wish I had filmed when I replaced everything forward of the firewall including the floor supports.

  • @FINfinFINfinFINfin
    @FINfinFINfinFINfin Před 2 měsíci

    Is the subframe chicom?

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 2 měsíci

      US made just a easy to miss alignment issue when it was jigged for welding. It's a nice heavy piece and looking forward to getting the car off the body cart and on the ground.

  • @donthompson2188
    @donthompson2188 Před 2 měsíci

    So let me get this straight, it just works? 😁😁😁

  • @dfhetzel
    @dfhetzel Před 2 měsíci

    Got mine last year to help with my own 66. You're right, its damn useful

  • @blueheeler2053
    @blueheeler2053 Před 2 měsíci

    Thanks Robert, good follow up review. I bought the M12 die/90 grinder on your recommendation, very happy.

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 2 měsíci

      Awesome. I'm a big fan of the m12 stuff too. Even my oldest stuff still works though I did wear out my first impact driver. It works but not as well. And my first batteries are still usable at well over 5 years old

  • @JoDaddysGarage
    @JoDaddysGarage Před 3 měsíci

    I feel your pain....

  • @mavmo192
    @mavmo192 Před 3 měsíci

    Get past it.

  • @dakel20
    @dakel20 Před 3 měsíci

    Pretty great video honestly! And yeah, I feel ya on the GoPro crap... Insta360 makes a decent camera for a good price, but these days I'm actually using a used Sony Handycam, ha.

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 3 měsíci

      Thanks. The Insta360 ace would be primarily what I'd be looking at buying but I have decided not to invest in another camera as there is no return on investment for me.

    • @dakel20
      @dakel20 Před 3 měsíci

      @@theinfernalcraftsman totally get it. I only have an insta360 because it's my bikes dash cam in case some lunatic decides today is a good day to hit a cyclist.

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 3 měsíci

      @@dakel20 Definitely worth it for that. I used to ride allot many years ago and got both our bikes out and cleaning them up etc as she wants to start riding on the trail system again. I won't ever be on the roads on one again though.

  • @mjay4700
    @mjay4700 Před 3 měsíci

    What were you even hanging that off of, the ends of a bolt on the garage track? Shortcuts sometimes end up costing you more time.

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 3 měsíci

      The bolt holes in the deck lid were stripped just enough that they seemed ok but on the 3rd time hanging it up one pulled out and the other went as well. No short cuts it's common practice to hang panels on far flimsier stands.

  • @davetyson2331
    @davetyson2331 Před 3 měsíci

    great video dont stop making them thanks

  • @laleena_daqueena3130
    @laleena_daqueena3130 Před 3 měsíci

    Trunk lids MAY have been injured in the filming of this video.😋

  • @edcucchiarella7994
    @edcucchiarella7994 Před 3 měsíci

    Love it, I have also had some parts "fly" out of the garage over the years!

  • @edward09603
    @edward09603 Před 3 měsíci

    We used similar seam sealers on antennas on aircraft when I was in the USAF. One of the things we did to smooth it out without it sticking to our fingers was to spray windex on our fingers. Smoothing out the beads was a breeze.

  • @shannonvaughan4354
    @shannonvaughan4354 Před 3 měsíci

    Door panels and clips are a real pain. I hope you have figured it out.

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 3 měsíci

      Oh those little things just don't like me. But as much as I complain about them they really do an excellent job of staying in place. Just not fun for the next guy.

  • @ronniewortham3260
    @ronniewortham3260 Před 3 měsíci

    Great video. Starting to work on a V-twin, I see the second part though, did it run afterwards?

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 3 měsíci

      Been running like new ever since. That said it was so dry last year I only cut twice. Already 4 times this year and it starts immediately every time. I often use it more for moving the trailer around than actually mowing. I do need an air ride seat for it since my yard is rough enough that it sends painful shocks up my spine every sip and bump. I have the tires as low as I can put them

    • @ronniewortham3260
      @ronniewortham3260 Před 3 měsíci

      @@theinfernalcraftsman I"m gonna start on my today probably, hopefully be as easy as yours was.

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 3 měsíci

      @@ronniewortham3260 Awesome. I wasn't really planning to record it when I did it so... And I didn't show it running because of the weather at the time and other constraints. The point of the video was to show it being done. Now I need to do some mods to it as I really wish it had more power. I replaced all but one of the pulleys recently because the sand I have ruins bearings very fast. One pulley is a royal pain to get to and fortunately it wasn't making much noise.

  • @user-pz1go1nu3r
    @user-pz1go1nu3r Před 3 měsíci

    Nice job…if you cut down an old blade to fit the star and use a bolt to secure it it would be easier to tighten and loosen the shaft…

  • @alexhellenbach8820
    @alexhellenbach8820 Před 3 měsíci

    Don't know you, don't know what your channel is about but I think it would be a blast having a beer with you. You seem like a fun person to hang with. (weird comment to post, I know lol)

  • @franciscogamboa5020
    @franciscogamboa5020 Před 4 měsíci

    Im having so much trouble with the driver side quarter panel. The oassenger sode fit really well, no trouble, but the driver side has me frustrated. 😅

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 4 měsíci

      Drivers side ones are a pain. There are around 4 different ones on the market and some of them are anywhere up to 3/8" longer than the original one. The Dynacorn one and Muscle Car GT ones are the best. But it's often hard to find out what brand you are being sent.

  • @fbombgarage
    @fbombgarage Před 4 měsíci

    How high from floor to rocker for clearance when rotating (I have 67 so I'm assuming to made a few for inches)

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 3 měsíci

      The 67 is about 3" wider at the mod to top of door area. Same floor pan though. I don't know exactly how high it was but if I were to do an educated guess the ponchweld was around 36" off the floor. There are the dimensions of the pivot points in a comment I left for another and you can use that to roughly calculate the flange height. I still had way more than enough room. A 67 wouldn't have really been any different on it from my perspective.

  • @chipjohnson5552
    @chipjohnson5552 Před 4 měsíci

    My 66 does not have ashtrays in the back.

  • @donsmanufactory
    @donsmanufactory Před 4 měsíci

    Betsy did not have ashtrays in the rear panels. Rear seat ash tray was in the console.

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 4 měsíci

      The last time this car was registered was in 82 or so. And I think they were probably jacked in there in the 70s by someone who smoked allot and had friends that did too. It is not allowed in or near anything we own.

  • @robertoruiz7069
    @robertoruiz7069 Před 4 měsíci

    Just found your channel and subbed. I have a 65 4speed that i've owned for 45 years that's sitting under a tarp.With the warm weather coming i 'm thinking of fixing it up. So i will be following you. ALSO thanks for the speech about the paint store that prices all the products. IU fully agree,i WANT to know BEFORE i go up to the counter what the cost ACTUALLY IS.thanks

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 4 měsíci

      Awesome. I appreciate it. I'm not the best at videos though. My goal is to just put out information for others to go off of and to put my rants about things in here and there. That paint store is jam packed full of inventory. Next time I make a trip up there I'm going to ask if they mind if I film inside. They also ship from their website as well. There will be some El Camino content in the near future. I'm hoping to get it over here soon. It's been stored at my parents for way too many years... It'll be a paint some mech work and get it sold.

  • @DirFootball2007
    @DirFootball2007 Před 4 měsíci

    You could turn the ashtray holes in the interior quarter trim into lighting.

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 4 měsíci

      I was also trying to come up with a way that those could be enlarged for speakers. Bad location for speakers but a thought.

  • @franswijnands4022
    @franswijnands4022 Před 4 měsíci

    I don't think you care what others think, but I'm still going to give my opinion......?..........?,,! It looks good 😂😂😂😂😂😂

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 4 měsíci

      That's very true. I also like to troll the purists that like everything original too. Thanks It was just a grab this i think it'll look ok kind of a deal. Yes it's 2:40am... It's soaking humid and the windows are open and I can't sleep. Won't get a good night sleep till winter when I can hibernate.

  • @carguytroy
    @carguytroy Před 4 měsíci

    I don't remember ever seeing ash trays there in a Mustang. I remember ash trays in the arm rests on the convertibles, but not sure on the coupes. I think I have have a set of those that are not cut up somewhere.Like the interior color. Looks great.

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 4 měsíci

      I'll have to do some looking and figure out where those things came from. But really someone needed 2 in the back seat... That said if it wasn't done so badly I would convert them to USB power ports. Thanks I'm pretty happy with how the color turned out.

  • @davetyson2331
    @davetyson2331 Před 4 měsíci

    door card look good i like your color choses

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 4 měsíci

      Thanks. The only sample of the color I had was the one they have at the store and I figured it was close enough and went with it.

  • @davetyson2331
    @davetyson2331 Před 4 měsíci

    good info and tips thanks

  • @rablwo
    @rablwo Před 5 měsíci

    Much appreciated!

    • @theinfernalcraftsman
      @theinfernalcraftsman Před 5 měsíci

      If I find a deck lid I'll post it in the community section. Will be around morning to mid day Friday if I find one there.

  • @JoDaddysGarage
    @JoDaddysGarage Před 5 měsíci

    Good information and nicely done.

  • @troyjustet8315
    @troyjustet8315 Před 5 měsíci

    This is good information for those of us who are wanting to do this on our cars.