Video

Yeah me too

Which three buttons are you pressing? The top three or bottom three? Are you pressing all three at the same time?

@@TheDavidPerich Which three buttons are you pressing? The top three or bottom three? Are you pressing all three at the same time?

@@rjracing38 I tried the top three I tried the bottom three I can’t get anything to work. It doesn’t beep or flash or do anything.

Some of them are still running these or they used to?

Great question...short answer, not very easily. Because the lightbar connects to this device via ethernet connection which comes off the circuit boat, there is a possibility with adding grille lights, etc but there would be a lot of reconfiguring and wiring involved to make it happen. Now, another option could be depending on the switch panel system you have that would control the SIM (Serial Interface Module). What controller/switch box/panel are you using in line with the SIM to control your lighting?

Does your Freedom lightbar have all the wires from the light heads to the mother board in the middle and controlled by the long control cable with about 18 different wires or do you have the style that is controlled off of cat5 ethernet cable to a wecan setup?

Thank you! Cheers!

Thank you! Cheers!

My apologies for the delays, I do not unfortunately make or sell the lightbars currently. I used to repair and fix a lot of them and still do from time to time.

I presume you are referring to the jumper wire bundle that has like the yellow, violet, white, green, etc multi-color wiring correct? If so, that will get power from the brain unit that you are using to activate certain patterns/modes. So for example, if you are activating you take-downs on he white/black wire, your switch box you have power to already will send power from the switch to the lightbar to activate that option for you. The only power you are putting directly from your power source/battery would be the power and ground wiring that is directly from the bar but the bundle wiring will be supplied power from your brain/switch box.

As far as I can tell, Code 3 offer a few new models, their Covert series Matrix, 16 series, 27 series and matrix along with heir Pursuit models currently. As far as official models available for sale in Brazil with regards to distributors, that I unfortunately do not know that market and area. Best thing you can try is visit their website and select your region/country and see if you can search for a dealer/distributor.

Depending on how yours is setup but there are a few wiring diagrams that you can find online on google that ill be available for download to show the wiring and what goes to where on your bar or at least a good start. This link here is one version I found for you, hope it helps gives you a good start and baseline for your bar; www.fedsig.com/sites/default/files/resource_library_document/2561340.pdf

This will work for the Valor lightbars as I have tested a few of them on the lightbars.

It depends on how the lightbar is setup. If the boards are setup with different color LEDs on each board, then you should be able to change the colors also depending on programming.

@@rjracing38 hmm ok thank you

Yup, that is the correct name, hence the correct title.

There is a way yes, I have done it with the Federal Signal software and plugged in my 6 button and 3 button controllers, used the software to reset each button and utilize the flashing takedown option.

@@rjracing38 thanks! Do you know how to make the control box beep when the lights are left on?

@@michaelf8500 , yes, in the Federal Signal program, there should be a section on the left hand side for button control that you can set the beep enabled and reminder for a certain amount of seconds that you would like.

@@rjracing38 unfortunately, the control box is installed in my vehicle. I was hoping there was a way using push button programming.

@@michaelf8500 , if you have a spare cat5 cable, you can unplug the cable from the control box and then plug in the new cat5 from your laptop to the head unit and program it from there. Setting up that kind of programming is only seen with the computer program but the push button programming in the vehicle gives you the option to change what pattern setup or what buttons will turn on or off a pre-programmed options within the head unit itself...

What Whelen controller are you trying to use with your Federal Signal Vision SLR and Serial Interface Module?

@@rjracing38 core/wecanx

Are you referring to lightbars in general, traffic advisors or which model? Most do require some sort of control box to tell certain lightheaded to activate, by what pattern, etc. Some of the old old lightbars could operate by a switch to activate power to a halogen bulb, small motor, etc.

Are you wanting to have the entire lightbar set up in cruise mode or just the standard corners that is normal?

Same question. Entire lightbar set up in cruise mode is what I want

I have a link in the description that has the direct download to the wiring diagram for the modules and which wire controls which function

@@rjracing38 thanks

Unfortunately I don't sell them myself but I have worked with a couple vendors to purchase them or have run the risk of locating them online used.

@rjracing38 would it work with a ss2000sm?

@@08_crown_vic, the 6-button controller or your Legend lightbar? Your lightbar has a cat5 wire/connection coming out of the bar along with obviously power and ground so your lightbar will connect to a 3/6/9-button controller like you have or can also connect via a serial interface module or even some of the new smart siren platinum controllers but the older ss2000sm I do not believe will not connect to your Legend light bar as that does not have the right connections. Let alone the 6-button controller you have wont hook-up to the ss2000sm either

Do any of the lights on the display of your controller light up? For example, when you have the toggle level in the off position, does the display light next to the number three illuminated and lighting the lightbar code 3?

Also, do you have your lightbar connected to the 6-button controller directly or do you have it connected in any other way?

​@@rjracing38Only the number 3 light turns on. The buttons stay on normally and work correspondingly. This is in mode 6 and each button performs the functions when I turn it to Off.

It turns on mode 3 and when I put it on mode 3 it turns off. Modes 1 and 2 work fine

​@@rjracing38Yes sir, you are connected to a legends bar

That they are, Federal Signal has been innovating since the early 1900's and their commitment to safety drives them to design better products each and every year.

Easy way to describe this is if you have the wiring schematic for the serial interface module so you know what wires activate what patterns that you are looking for and then hook those corresponding wires to the switch box for which ever switch or toggle you are looking to activate.

Thanks got working

The switch box I was able to locate one locally but you can find them online as well I'm sure. Most of them will have wiring extended out the back that you can tap into for the different setups of the lightbars. This particular one I was using I also modified slightly and added an extra switch.

I would double check how wide the top of your vehicle is to make sure. This particular one was installed to a Chevrolet Tahoe and fit perfectly so more than likely. Federal Signal makes the Valor lightbars in 44" and 51" as this model showcased in the video was the 44" model.

Thank you for watching, greatly appreciate it :D

@@rjracing38 You're very welcome

Yes, depending on how the departments would like their bars setup, you can put the takedown setup in the middle/center of the bar or slightly outward to give a little more light. Some of the new bars now give you the option you can make the entire front of the bar be the take down lights.

@@rjracing38 RCMP did use this setup on the wider versions like on a Tahoe, Silverado, Suburban, Econoline, Chevy Express and Ford F Super Duty and rarely on the Police Interceptors like the Explorer and Taurus. Sometimes it setup in the middle

@@GRC6401 Yup, long as there is good lighting for everyone's safety, that's what matters.

@@rjracing38 It currently applies for the Whelen Century for the newer units

@@GRC6401 yup, the Century Elites and legacy, the low pro versions of the Liberty 2 and Freedom 4 bars, are in the center and the Cenators are almost to the edges of the lightbar similar to the Edge 9xwhile the Justice has them towards the outer edges. Whelen for their take down lights and their alley lights still utilize their LR11 led setups.

At the time of filming this, I was using the 6-button controller but since has been upgraded to the Smart Siren Platinum series controller.

Nice, the Century lightbars felt like they were a combination of the Liberty style and Justice light bars just about but I know a majority of their newer style bars are going that way in looks/style.

There’s a longer variant for the pickups and vans

@@GRC6401 yup, they have the 50" models which work well for the wider SUVs an such.

2:01 RCMP uses this when they are parked at some scenes

2:42 2:52 5:24 6:10 It did use those patterns while responding

That will require different LED modules and more LEDs, a control board to handle that and programming to tell the board what LED color to activate on what model, etc. I have gone through this on another lightbar I custom made for someone and not super difficult but timely and can be expensive to setup.

If it is just the one corner side not functioning or powering on, there could be a few things that could be an issue. There could be a faulty board that went out, faulty wiring/connection, lack of power to the corner board, etc. Another thing that could be that I have seen a few times on repairs is with the corner modules run them as a "master" and a "slave" driver circuit board and if the "master" board or the rear board is not getting power, it will not feed power to the "slave" driver circuit or the front board using the white master/slave control wire.

@@rjracing38 I switched the positive to another positive and both corners work now.

@@molyoxide164 awesome, sounds like maybe the original power lead wasn't supplying power for whatever reason. Glad you got it working!

@@rjracing38 I got this bar for 100$’s so I’m happy with it tho, as their very expensive…

@@molyoxide164 that's awesome! It's always great to find a good deal on some of these bars.

Yeah, I have seen a lot of officers do that which baffles me.

Easy thing you can do if you would like is just a regular car battery. Or another option you can use is a AC to DC power converter. The one I use for my setups on my displays and test bench is the Tripp Lite PR60 power supply.

Yours is flashing left and right side synchronized before using a jumping wire in the 3-pin plug? Or was it flashing random patterns on each light head but left and right side?

@@rjracing38 yeah flashing left & right b4 using sync wire

@@daverogers7512 Are all the light heads that are flashing on the left flashing together at the same time with the same patterns? If so, I'm wondering if someone had either gone through and took the time to program each lighthead to have the same pattern setup on the entire bare so it was acting like the sync wire was powered up.

@@rjracing38 Thanks for getting back to me t’s always been set to random one day it just synced 🤷‍♂️ tried all the tricks no joy

@@daverogers7512 If everything was random before and then all of a sudden started syncing, somehow that circuit is now getting power. Is yours the LC bar?

What issues are you having and which bars?

This was my very first bar I received that didn't have any wiring in it and figured out how the wiring needed to be, wired it all up and got a harness made and got it up and running.

Thanks :-D

You can dim the lightbar. Depending on how yours may be setup, traditionally the dimming or low power function will typically be on the purple or violet wire. Once you have power to the lightbar and the pattern running, you can activate a switch directly to this wire and should put the lightbar in a low power function making the leds dim down.

There is a way to have the lights be set in a synchronized pattern which I have made a video showing how to wire it up and set everything up. The video link is; czcams.com/video/M5X1kl8aloo/video.html also labeled Whelen Liberty Sync Wiring. Hope this helps out

He visto muchos de ellos como estos, algo genial

One of the best

Hey, sorry for the delays, I have noticed from the address I had for the link had been removed or something but I can get my paperwork scanned in and emailed over to you if you still need.

So you could probably find one online somewhere for probably too much honestly. Best bet in my opinion is you can look up the electronic manual online on Federal Signal's website and just make one yourself with some small gauge wiring. I believe mine has a two pin connector but only one red wire for power.

@@rjracing38 Yeah, I was looking online for it but no luck and I could not find any on Federal Signal website. So there id two pin connector on the controller one is for power and what is the other one for if you don't mind my asking?

On this one, I actually made my own controller but since this video, I came across a good condition Federal Signal SW400SS control box.

Yes, if you have the S2 model with the cat5 connection, that cat5 wire will need to be connected to a control head or any of the Federal Signal devices compatible with the convergence network ports such as the pathfinder sire/light controller, 3/4/6/9 button controllers, smart siren platinum controllers, etc. If you don't have any of those, you will need at the least the serial interface module to plug the lightbar into and then from there, there's a wire harness that you can plug into some aftermarket controllers or even some of the older models such as a 6-button switch box of 4-button switch box with slide switch setup. Then your positive and negative wires coming from the lightbar will connect to your power supply.

@@rjracing38 Wow, that sounds rather complicated. I didn't realize all that stuff went into these lightbars.....All I did was drive these radio cars and take people to jail:).... thanks for this info.....it's a great help.....

@@allenkunihiro9081 haha, it's not too bad but it can be overwhelming at first. I learned everything by tinkering and playing with them, next thing I knew, I had a few reach out to fix their bars and even had some local PD hit me up cause their repair department was falling behind and I was able to get them going with rather quick fixes. You are very welcome. Glad to help.

I am, what question do you have?