Video

how was it removed? mine is bumping that engine mount and could not be pulled out

Is there another kind of pulley

I know you explained good but my problem is to identify the hoses in the firewall … I would like to send you pictures…

Please Do you have a video showing how to install or how is the positions for all the A/C manifold hoses ? A little help ... i just took it apart but I don't remember exactly. Thank you so much. .

turn off the music maan

i'm not a mechanic i'm very concerned now because last week my air was blowing warm I bought a small can of freon with leak sealer and put it in through my low side my truck started blowing cold again for exactly 7 days I just came from a shop and they said my compressor was bad; is it possible that I could've still put freon in and got cold air again with a bad compressor they said my system was all charged and full of freon they didn't say anything about a leak.

I don't see a pedal control sensor on a 2000 Sentra does it have one?

Where did u get the customer knobs ?

at timestamp 6:13 I paused it to see where and how you affixed the belt to the pully but it is too dark to see what you did : (

I wish you would have illuminated the area where you attached the belt to the pully system. Can you explain how you did that?

Witch section applys to the 06 sentra for the relearn in the description there is 4 different sections with steps ?

Video taken by the makers of The Blair Witch Project.

احسنت

The bottom hose of the cooler is it the inlet or outlet? And which one should flush ?

Do you recommend Castrol CVT fluid for a 2008 nissan Rogue Awd ? Castrol ? Valovoline? Mobil? Oreilys? STP ? Wich is a better CVT fluid?

Dear. Thanks so much for your video. I have a question. The throtle body have a small screw. Do you know what is the funtion of these screw. I saw that I can move the screw. What adjusting these screw. Please your help. My B15 2005 have a problem when a put march the RPM down to 450 Rpm and when I return to parking or neutral the Rpm are in 750 Rpm

What the f*** are you talking about you need to take the compressor off to replace that switch that is the biggest load of b******* I've ever heard All you got to do is remove the cooling fan out of your way or use a pair of 90° snap ring pliers are you smoking something

No

Thank you so so so much I save my self a few hundred dollars here.🎉

With way does the belt goes

Very bad video..

My belt keeps on breaking

Question do you have to use a sealing around the housing because I see you didnt.

This is an insane vid

Good video😊!!! 👍 I’ve done this a year or two ago, but forgot how to open the dang’ thing! I guess I’m putting TOOOOO many heavy, wet clothes in there! 🤷‍♂️ I need to order more belts, cuz’ I “KNOW” I’m going to be doing this again! 🤨 Thanks for the video. Life of Tin and Ed 😊

Trash video

I've built cars and worked on tons more, My 02 Sentra has given me the biggest headache I've ever delt with. I cleaned my throttle body and started having high idle so I cleared the codes, did the relearn process, checked for leaks, check MAF, spark plus, and everything just to realize I damaged the Throttle Botty by barely messing with it 🤦🏽‍♂️

I need to know and understand that all Korean Nissan CVT have clear CVT fluid!! Amsoil or Valvoline preferably has to be NS2 or NS3 compatible!! The red CVT fluid is for Toyota or Subaru remember that not knocking you videos thanks for the video!! Good luck!! Okay thanks just ask any service dealer about for sure!! Okay thanks 👍👍👍😮😳🤯👌👍👍

I have this car. You don't need the to buy the plastic kit shown here. You just need to locate the air release plug and release the air while filling.

QUESTION PLEASE: Where does the other end of the capillary tube go to on an older Kenmore (circa 2002 w/Freezer on top) with the freezer on the top of fridge. Does it go to the Evaporator fan area in the freezer? It would be very helpful if you could please share the information.Thanks. Phil

How did u know it was the fuel pump that need replacing, my car’s misfiring in the third cylinder and someone said fuel pump and someone said compression , but look at the fuel pump would that specifically cause my third cylinder to misfire?

Thanks for the help my guy.

Looks like a CV rubber boot or an auto rack and pinion boot would be an improvement. Those working angles looked extreme. 😊.PS. Some motorcycle fork boots would've probably been a good factory mod on those exposed steering ram shafts

Sir hamare mashin me esahi sound ata he

Very good job

Thanks for the info. Ditch the music please.

Ty sir!

nice video, thanks man

Why are there too sets of slots for the pulley.

thank you .wish I could hire you to do mine but now I know !

whirlpool dryer wgd5300sq0 pulley on motor replacement. Looking for part number for pulley it broke and need replacement

Thank you for the video!!!

Very helpful video. My only suggestion would be to show a little more detail on the tensioner pulley for those that can't see that well. Other than that, thanks for the HELP...

3weeks ago there I sat.. confident... determined... waiting on the spin cyle to sound its buzz of completion, alerting me it was then time.. the time ...to embark on the new mission..the next step..the required procedure that when its completed in the correct order of operations. I knew my desiered outcome was in grasp..unfortunately though, I just recently realized this task is now my sole responsibility to bare and accomplish alone.. at my own detriment.. assuming of coarse that my transition towards my new transformation to this batchlor-ism is now my new lifestyle inwhich I must quickly adapt and over come.. when I realized I didn't have a dryer belt my MacGyver instincts began to take over and since zipties work as a belt for me sometimes I knew I could pull it off the same way with this may tag machine..the pully at the bottom of the belt kicked my ass for about 4 hours and right before I gave up and resided to my sugamammas or local laundrymat I ran across this video and within seconds my ziptie belt i installed and this CZcams pully class I completed I was now ready to move on to firing up this well oiled machine to get this baby spinning like my head is driving right now in the interste.. I hit start and the sob broke after about 2 minutes and 15 seconds so I took a sabaticle until tonight because I finally got a belt.. I though to myself well I atleast know how to put on the pulley and u know what.? It kicked my ass and I had to look it up again.. fml

Very good video thanks

Great video you may want to remind your viewers to use a lil bit of anti-seize thread lubricant on the fill and drain plugs as they are dissimilar metals. Anyway, great how to video.

You helped me over the summer, and here I am again 😢 thank you

Thanks man! You saved me hundreds of dollars!

Great video appreciate the effort

good video very informative. helped me with a job.