Video

Thanks! Solved my issue 😀😀

I think I got the same problem with my v8 soft brush. After cleaning everything it only spins for a few seconds and than stops. I don't have the professional tools to check, but this also sounds like a wire problem right?

Show about if the motor is spinning very strong and the little chrome cross-bar seems to be spinning with full strength…..until you place the brush head into the holder and then the motor balks and gets hung up? Anyhow have experience with this scenario?

Thanks a lot for the video, I managed to fix it as well.

I removed the motor. Now i cant attached it back as the wire is deep in the holder

Very helpful video. Only difference is that when i pulled out the motor with the gear it had the 3 other gears that go around it stuck there as well, and it was a pain in the ass to get it back innside with the right gear position. Ended up pushing the top part with the 3 rods for the 3 gears down and out so i could mount it before sliding the whole thing back into the casing and secure it. recommend running it a bit before full assembly to listen for gear whine. Mine was off by 1 notch and made a grinding whirring sound so i had to repeat the whole process ^^

Worked perfect ! 👍 thx

My problem is that not only does the brush not turn but I can’t even get it out. I have the little cap off, but can’t get the brush to come loose, even pulling with a vice grips. I have the belt off but can’t go any further without getting at that last screw, since the brush won’t come out. Any suggestions?

I when0 had the Mega S never had any problems. Whereas with the Kobra Neo I do and now when I insert the filament it comes out perfectly melted. But during the spampa nothing comes out. I got fed up with the standard insignificant extruder and put the one on the Kobra2 hoping for success but in this case the motor refuses to work. I ran the 'firmware update ...... . Solutions ? Thank you very much.

Thank youuuuu.

watch?v=GhabJc13_Ok 🙂. Though granted, your film quality is a lot better than mine.

Hello sir, I have v15. LCD screen broke by itself. Can you have any part number for only screen replacement

How do you copy the data from the old chip to the new one?

Thank you

Excellent video thank you very much

Please let me know how to open the part ( the one that was taken off camera ) , I am stuck there .

My V8 just died and has 4 Flashing Red lights on the battery pack... I'm reading things that it might be a motor issue, can you confirm?

Hiii what would your recommendation be for when the cyclone motor body gets wet. For context my bf vacuumed beer up on a Saturday night so Monday night I made sure to clean my Dyson parts and dusted off the cyclone body, also let it rest our side so that any moisture could dry. This morning I woke up to it drizzling, I haven’t tested it out as I’m waiting for it to hopefully air dry. So idk I’m just looking for guidance on what to do since warranty doesn’t cover it and they’re out of stock right now. Thank you

Hiii what would your recommendation be for when the cyclone motor body gets wet. For context my bf vacuumed beer up on a Saturday night so Monday night I made sure to my Dyson parts and dusted off the cyclone body, also let it rest our side so that any moisture could dry. This morning I woke up to it drizzling, I haven’t tested it out as I’m waiting for it to hopefully air dry. So idk I’m just looking for guidance on what to do since warranty doesn’t cover it and they’re out of stock right now. Thank you

I have the same problem with my printer, but I looked at the cables and couldn't see anything. What should I do ?

I've changed my dyson v10's trigger but when I put battery on it starts running and does not stop. I suspect that my triggers tail is longer than it should be. Do you have any suggestions?

Got the same issue with a Anycubic Max and have reached out to Anycubic for parts to replace possible broke wires. Unfortunaly Anycubic has not responded to any of my requests. Is there a web page where parts can be purchased that you are aware of? Thanks.

I have One R, and water has entered through charging port. Can you repair it.

Worked like a charm!

Guess I'll return it Costco since it's under 3 years old and just get a new one.

Como se llama el sujetado o torque que va con el motor DC para las puntas

Amazing. I had this on my first unit after one week of use. Dyson support did not suggest doing this, they instead took it for repair and ended up sending me a new one. Well, after two weeks with the new one its done the same thing and I was almost about to get in touch with support... but this two button reset did the trick instantly. Does anyone know why it does this in the first place?

Super Erklärung, ich musste den shit Schalter wechseln wegen der Sollbruchstelle.

Thank you this helped a lot! I was about to return the unit due to broken sensoe - turns out air in Copenhagen is just *that* clean.

thanks for sharing!

Thank you very much

Gracias!

Mine shaft doesn't rotate with loads and without loads, what can it be?

Mine doesn't spin in any case, with brush and without brush, the rotor doesn't rotate What can it be? I don't know how to solve

Dziękuje za pomoc . Bez tego filmiku nie wiedziałbym jak wyciągnąć włącznik . Pozdrawiam

Can this area which you used a bulb air blower be carefully suctioned/vacuumed instead? Can the sensor surface (shiny circle that looked like it had dust smudges on it) be further cleaned with alcohol or like?

This is cool and all but I’m not doin all this lmao

Brilliant. Absolutely outstanding fix.

Do you have any video which gives info about the thin red and white wires? What is the voltage of that and where is it connected? I have to test a dyson v6l motor without other parts just by itself and there is no info, I guess 3.3v or 5v but I want to be sure.

Dzięki super materiał bardzo mi pomogłeś. Pozdrawiam z polski.

Thank you very much. You are the best. Perfect video 👍

Thank you for the helpful video! Unfortunately, the display no longer turns on and the vacuum cleaner is pulsing. Could you please let me know what I might have done wrong?

Thanks a lot for the vid. Funny thing is I looked this up because i was unable to open mine - turned out in my case the big wheel fused to the cover! It turned out that the plastic frame holding the wheel even broke from the strain of it being fused. I swear this shit is made to break eventually :<

Thanks! By the hal magnet test i was able to fix mine! It wasn’t touching anymore

Thanks alot my man!! Worked for me.. saved me a couple of $$$!! 🫶🏻

Спасибо за видео!

Thanks a lot , realy helped me to repair my v8 Dyson with this problem - Aliexpress - 1.2 EUR per 1 MOSFET plus "small" work

Thank you so much for guidance. Within an hour replaced trigger switch. 👍👍👍👍

Do you also have a video for V12?

cómo puedo encender y apagar mi purificador en mi celular no me responde si puedo ver la contaminación y las funciones pero no lo puedo controlar :(